[v2,2/5] arm: dts: colibri-imx6: move vbus-supply to module level device tree

Commit Message

Marcel Ziswiler Sept. 28, 2022, 7:33 a.m. UTC

From: Marcel Ziswiler <[e-mail]>

Move USB VBUS supply from single carrier board to module level device
tree. This pin is as per Colibri module family standard.

Signed-off-by: Marcel Ziswiler <[e-mail]>
---

(no changes since v1)

 arch/arm/boot/dts/imx6dl-colibri-aster.dts   | 1 -
 arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts | 1 -
 arch/arm/boot/dts/imx6dl-colibri-iris.dts    | 1 -
 arch/arm/boot/dts/imx6qdl-colibri.dtsi       | 9 +++++++--
 4 files changed, 7 insertions(+), 5 deletions(-)

Patch

diff --git a/arch/arm/boot/dts/imx6dl-colibri-aster.dts b/arch/arm/boot/dts/imx6dl-colibri-aster.dts
index 74e8a6cd8bed..a28e083f29d5 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-aster.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-aster.dts
@@ -99,7 +99,6 @@  &uart3 {
 };
 
 &usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
index 7272edd85a49..a02981d4a3fc 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
@@ -111,7 +111,6 @@  &uart3 {
 };
 
 &usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6dl-colibri-iris.dts b/arch/arm/boot/dts/imx6dl-colibri-iris.dts
index cf77d894f6d7..c5797ff35b71 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-iris.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-iris.dts
@@ -138,7 +138,6 @@  &uart3 {
 };
 
 &usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 3e98b5da0cc6..21c5049bda4e 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -112,7 +112,7 @@  reg_module_3v3_audio: regulator-module-3v3-audio {
 
 	reg_usb_host_vbus: regulator-usb-host-vbus {
 		compatible = "regulator-fixed";
-		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; /* USBH_PEN */
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; /* SODIMM 129 / USBH_PEN */
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
 		regulator-max-microvolt = <5000000>;
@@ -677,6 +677,11 @@  &uart3 {
 	status = "disabled";
 };
 
+/* Colibri USBH */
+&usbh1 {
+	vbus-supply = <&reg_usb_host_vbus>;
+};
+
 /* Colibri USBC */
 &usbotg {
 	disable-over-current;
@@ -995,7 +1000,7 @@  MX6QDL_PAD_SD4_DAT2__PWM4_OUT	0x1b0b1
 
 	pinctrl_regulator_usbh_pwr: gpioregusbhpwrgrp {
 		fsl,pins = <
-			/* USBH_EN */
+			/* SODIMM 129 / USBH_PEN */
 			MX6QDL_PAD_EIM_D31__GPIO3_IO31	0x0f058
 		>;
 	};