| Message ID | 20221102134923.3438022-2-w.egorov@phytec.de (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/2] dt-bindings: arm: ti: Add bindings for PHYTEC AM64x based hardware | expand |
On 02/11/2022 09:49, Wadim Egorov wrote: > Add basic support for phyBOARD-Electra-AM642. > > Supported features: > * Debug UART > * Heartbeat LED > * GPIO buttons & LEDs > * SPI NOR flash > * SPI TPM Chip > * eMMC > * CAN > * Ethernet > * Micro SD card > * I2C EEPROM > * I2C RTC > * LED Dimmer > * USB > > Signed-off-by: Wadim Egorov <w.egorov@phytec.de> > --- > arch/arm64/boot/dts/ti/Makefile | 1 + > .../boot/dts/ti/k3-am64-phycore-som.dtsi | 379 ++++++++++++++++++ > .../dts/ti/k3-am642-phyboard-electra-rdk.dts | 313 +++++++++++++++ > 3 files changed, 693 insertions(+) > create mode 100644 arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi > create mode 100644 arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts > > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile > index 4555a5be2257..79331f16cd4b 100644 > --- a/arch/arm64/boot/dts/ti/Makefile > +++ b/arch/arm64/boot/dts/ti/Makefile > @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb > dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb > > dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb > +dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb > dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb > > dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb > diff --git a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi > new file mode 100644 > index 000000000000..ecd0050a84e6 > --- /dev/null > +++ b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi > @@ -0,0 +1,379 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2021 PHYTEC America, LLC - https://www.phytec.com > + * Author: Matt McKee <mmckee@phytec.com> > + * > + * Copyright (C) 2022 PHYTEC Messtechnik GmbH > + * Author: Wadim Egorov <w.egorov@phytec.de> > + */ > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/net/ti-dp83867.h> > + > +/ { > + model = "PHYTEC phyCORE-AM64x"; > + compatible = "phytec,am64-phycore-som"; > + > + aliases { > + mmc0 = &sdhci0; > + rtc0 = &rv3028; > + }; > + > + memory@80000000 { > + device_type = "memory"; > + reg = <0x00000000 0x80000000 0x00000000 0x80000000>; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + secure_ddr: optee@9e800000 { > + reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ > + alignment = <0x1000>; > + no-map; > + }; > + > + main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa0000000 0x00 0x100000>; > + no-map; > + }; > + > + main_r5fss0_core0_memory_region: r5f-memory@a0100000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa0100000 0x00 0xf00000>; > + no-map; > + }; > + > + main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa1000000 0x00 0x100000>; > + no-map; > + }; > + > + main_r5fss0_core1_memory_region: r5f-memory@a1100000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa1100000 0x00 0xf00000>; > + no-map; > + }; > + > + main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a2000000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa2000000 0x00 0x100000>; > + no-map; > + }; > + > + main_r5fss1_core0_memory_region: r5f-memory@a2100000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa2100000 0x00 0xf00000>; > + no-map; > + }; > + > + main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a3000000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa3000000 0x00 0x100000>; > + no-map; > + }; > + > + main_r5fss1_core1_memory_region: r5f-memory@a3100000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa3100000 0x00 0xf00000>; > + no-map; > + }; > + > + rtos_ipc_memory_region: ipc-memories@a5000000 { > + reg = <0x00 0xa5000000 0x00 0x00800000>; > + alignment = <0x1000>; > + no-map; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&leds_pins_default>; > + > + led-green { > + function = LED_FUNCTION_HEARTBEAT; > + gpios = <&main_gpio0 12 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + default-state = "on"; > + }; > + }; > + > + vcc_5v0_som: fixed-regulator-vcc-5v0-som { Drop "fixed" in node name. > + /* VIN / VCC_5V0_SOM */ > + compatible = "regulator-fixed"; > + regulator-name = "VCC_5V0_SOM"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + regulator-boot-on; > + }; > +}; > + > +&main_pmx0 { > + cpsw_mdio_pins_default: cpsw-mdio-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ > + AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ > + AM64X_IOPAD(0x0100, PIN_OUTPUT, 7) /* (V7) PRG1_PRU0_GPO18.GPIO0_63 */ > + >; > + }; > + > + cpsw_rgmii1_pins_default: cpsw-rgmii1-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0184, PIN_INPUT, 4) /* (W6) PRG0_PRU0_GPO9.RGMII1_RX_CTL */ > + AM64X_IOPAD(0x0188, PIN_INPUT, 4) /* (AA5) PRG0_PRU0_GPO10.RGMII1_RXC */ > + AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */ > + AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */ > + AM64X_IOPAD(0x01cc, PIN_INPUT, 4) /* (W5) PRG0_PRU1_GPO7.RGMII1_RD0 */ > + AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */ > + AM64X_IOPAD(0x01d4, PIN_INPUT, 4) /* (Y5) PRG0_PRU1_GPO9.RGMII1_RD1 */ > + AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */ > + AM64X_IOPAD(0x01d8, PIN_INPUT, 4) /* (V6) PRG0_PRU1_GPO10.RGMII1_RD2 */ > + AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */ > + AM64X_IOPAD(0x01f4, PIN_INPUT, 4) /* (V5) PRG0_PRU1_GPO17.RGMII1_RD3 */ > + AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */ > + AM64X_IOPAD(0x0154, PIN_INPUT, 7) /* (V12) PRG1_PRU1_GPO19.GPIO0_84 */ > + >; > + }; > + > + eeprom_wp_pins_default: eeprom-wp-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0208, PIN_OUTPUT, 7) /* (D12) SPI0_CS0.GPIO1_42 */ > + >; > + }; > + > + leds_pins_default: leds-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0030, PIN_OUTPUT, 7) /* (L18) OSPI0_CSn1.GPIO0_12 */ > + >; > + }; > + > + main_i2c0_pins_default: main-i2c0-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0260, PIN_INPUT, 0) /* (A18) I2C0_SCL */ > + AM64X_IOPAD(0x0264, PIN_INPUT, 0) /* (B18) I2C0_SDA */ > + >; > + }; > + > + ospi0_pins_default: ospi0-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* (N20) OSPI0_CLK */ > + AM64X_IOPAD(0x0008, PIN_INPUT, 0) /* (N19) OSPI0_DQS */ > + AM64X_IOPAD(0x000c, PIN_INPUT, 0) /* (M19) OSPI0_D0 */ > + AM64X_IOPAD(0x0010, PIN_INPUT, 0) /* (M18) OSPI0_D1 */ > + AM64X_IOPAD(0x0014, PIN_INPUT, 0) /* (M20) OSPI0_D2 */ > + AM64X_IOPAD(0x0018, PIN_INPUT, 0) /* (M21) OSPI0_D3 */ > + AM64X_IOPAD(0x001c, PIN_INPUT, 0) /* (P21) OSPI0_D4 */ > + AM64X_IOPAD(0x0020, PIN_INPUT, 0) /* (P20) OSPI0_D5 */ > + AM64X_IOPAD(0x0024, PIN_INPUT, 0) /* (N18) OSPI0_D6 */ > + AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* (M17) OSPI0_D7 */ > + AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */ > + >; > + }; > +}; > + > +&cpsw3g { > + pinctrl-names = "default"; > + pinctrl-0 = <&cpsw_rgmii1_pins_default>; > +}; > + > +&cpsw3g_mdio { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&cpsw_mdio_pins_default>; > + > + cpsw3g_phy1: ethernet-phy@1 { > + compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + interrupt-parent = <&main_gpio0>; > + interrupts = <84 IRQ_TYPE_EDGE_FALLING>; > + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; > + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; > + reset-gpios = <&main_gpio0 63 GPIO_ACTIVE_LOW>; > + reset-assert-us = <1000>; > + reset-deassert-us = <1000>; > + }; > +}; > + > +&cpsw_port1 { > + phy-mode = "rgmii-rxid"; > + phy-handle = <&cpsw3g_phy1>; > +}; > + > +&cpsw_port2 { > + status = "disabled"; > +}; > + > +&mailbox0_cluster2 { > + mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 { > + ti,mbox-rx = <0 0 2>; > + ti,mbox-tx = <1 0 2>; > + }; > + > + mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 { > + ti,mbox-rx = <2 0 2>; > + ti,mbox-tx = <3 0 2>; > + }; > +}; > + > +&mailbox0_cluster3 { > + status = "disabled"; > +}; > + > +&mailbox0_cluster4 { > + mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 { > + ti,mbox-rx = <0 0 2>; > + ti,mbox-tx = <1 0 2>; > + }; > + > + mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 { > + ti,mbox-rx = <2 0 2>; > + ti,mbox-tx = <3 0 2>; > + }; > +}; > + > +&mailbox0_cluster5 { > + status = "disabled"; > +}; > + > +&mailbox0_cluster6 { > + mbox_m4_0: mbox-m4-0 { > + ti,mbox-rx = <0 0 2>; > + ti,mbox-tx = <1 0 2>; > + }; > +}; > + > +&mailbox0_cluster7 { > + status = "disabled"; > +}; > + > +&main_i2c0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_i2c0_pins_default>; > + clock-frequency = <400000>; > + > + eeprom@50 { > + compatible = "atmel,24c32"; > + pinctrl-names = "default"; > + pinctrl-0 = <&eeprom_wp_pins_default>; > + pagesize = <32>; > + reg = <0x50>; > + }; > + > + rv3028: rtc@52 { > + compatible = "microcrystal,rv3028"; > + reg = <0x52>; > + trickle-resistor-ohms = <3000>; > + }; > + > + lp8733: lp8733@61 { Node names should be generic. https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation It looks like "pmic" > + compatible = "ti,lp8733"; > + reg = <0x61>; > + > + buck0-in-supply =<&vcc_5v0_som>; > + buck1-in-supply =<&vcc_5v0_som>; > + ldo0-in-supply =<&vdd_3v3>; > + ldo1-in-supply =<&vdd_3v3>; > + (...) > + > + user-leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&user_leds_pins_default>; > + > + user-led0 { > + gpios = <&main_gpio0 15 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "gpio"; > + default-state = "on"; > + }; > + > + user-led1 { > + gpios = <&main_gpio0 16 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "gpio"; > + default-state = "on"; > + }; > + }; > + > + vcc_3v3_mmc: fixed-regulator-sd { Drop "fixed" > + /* TPS22963C */ > + compatible = "regulator-fixed"; > + regulator-name = "VCC_3V3_MMC"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > +}; > + > +&main_pmx0 { > + can_tc1_pins_default: can-tc1-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0084, PIN_OUTPUT, 7) /* (P16) GPMC0_ADVn_ALE.GPIO0_32 */ > + >; > + }; > + > + can_tc2_pins_default: can-tc2-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0090, PIN_OUTPUT, 7) /* (P17) GPMC0_BE0n_CLE.GPIO0_35 */ > + >; > + }; > + > + gpio_keys_pins_default: gpio-keys-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0044, PIN_INPUT, 7) /* (T18) GPMC0_AD2.GPIO0_17 */ > + AM64X_IOPAD(0x0054, PIN_INPUT, 7) /* (V20) GPMC0_AD6.GPIO0_21 */ > + >; > + }; > + > + main_i2c1_pins_default: main-i2c1-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0268, PIN_INPUT, 0) /* (C18) I2C1_SCL */ > + AM64X_IOPAD(0x026c, PIN_INPUT, 0) /* (B19) I2C1_SDA */ > + >; > + }; > + > + main_mcan0_pins_default: main-mcan0-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0250, PIN_OUTPUT, 0) /* (A17) MCAN0_TX */ > + AM64X_IOPAD(0x0254, PIN_INPUT, 0) /* (B17) MCAN0_RX */ > + >; > + }; > + > + main_mcan1_pins_default: main-mcan1-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (C17) MCAN1_TX */ > + AM64X_IOPAD(0x025c, PIN_INPUT, 0) /* (D17) MCAN1_RX */ > + >; > + }; > + > + main_mmc1_pins_default: main-mmc1-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */ > + AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */ > + AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */ > + AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */ > + AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */ > + AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* MMC1_CLKLB */ > + AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ > + AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */ > + >; > + }; > + > + main_spi0_pins_default: main-spi0-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x020c, PIN_OUTPUT, 7) /* (C13) SPI0_CS1.GPIO1_43 */ > + AM64X_IOPAD(0x0210, PIN_INPUT, 0) /* (D13) SPI0_CLK */ > + AM64X_IOPAD(0x0214, PIN_OUTPUT, 0) /* (A13) SPI0_D0 */ > + AM64X_IOPAD(0x0218, PIN_INPUT, 0) /* (A14) SPI0_D1 */ > + >; > + }; > + > + main_uart0_pins_default: main-uart0-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */ > + AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */ > + >; > + }; > + > + main_uart1_pins_default: main-uart1-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ > + AM64X_IOPAD(0x024C, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ > + AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */ > + AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ > + >; > + }; > + > + main_usb0_pins_default: main-usb0-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ > + >; > + }; > + > + pcie_usb_sel_pins_default: pcie-usb-sel-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x017c, PIN_OUTPUT, 7) /* (T1) PRG0_PRU0_GPO7.GPIO1_7 */ > + >; > + }; > + > + pcie0_pins_default: pcie0-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x0098, PIN_OUTPUT, 7) /* (W19) GPMC0_WAIT0.GPIO0_37 */ > + >; > + }; > + > + user_leds_pins_default: user-leds-pins-default { > + pinctrl-single,pins = < > + AM64X_IOPAD(0x003c, PIN_OUTPUT, 7) /* (T20) GPMC0_AD0.GPIO0_15 */ > + AM64X_IOPAD(0x0040, PIN_OUTPUT, 7) /* (U21) GPMC0_AD1.GPIO0_16 */ > + >; > + }; > +}; > + > +&main_i2c1 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_i2c1_pins_default>; > + clock-frequency = <400000>; > + > + eeprom@51 { > + compatible = "atmel,24c02"; > + pagesize = <16>; > + reg = <0x51>; > + }; > + > + pca9533d: led-dimmer@62 { > + compatible = "nxp,pca9533"; > + reg = <0x62>; > + > + rgb-red { > + type = <PCA9532_TYPE_LED>; > + default-state = "on"; > + }; > + > + rgb-green { > + type = <PCA9532_TYPE_LED>; > + default-state = "on"; > + }; > + > + rgb-blue { > + type = <PCA9532_TYPE_LED>; > + default-state = "on"; > + }; > + }; > +}; > + > +&main_mcan0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_mcan0_pins_default>; > + phys = <&can_tc1>; > +}; > + > +&main_mcan1 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_mcan1_pins_default>; > + phys = <&can_tc2>; > +}; > + > +&main_spi0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_spi0_pins_default>; > + cs-gpios = <0>, <&main_gpio1 43 GPIO_ACTIVE_LOW>; > + ti,pindir-d0-out-d1-in; > + > + slb9670: tpm20@1 { Node name just "tpm" > + compatible = "infineon,slb9670"; > + reg = <1>; > + spi-max-frequency = <10000000>; > + }; > +}; Best regards, Krzysztof
On 14:49-20221102, Wadim Egorov wrote: > Add basic support for phyBOARD-Electra-AM642. > > Supported features: > * Debug UART > * Heartbeat LED > * GPIO buttons & LEDs > * SPI NOR flash > * SPI TPM Chip > * eMMC > * CAN > * Ethernet > * Micro SD card > * I2C EEPROM > * I2C RTC > * LED Dimmer > * USB Optionally: please add a immutable link to the product (if possible with board information and details) Quick scan comments below. > > Signed-off-by: Wadim Egorov <w.egorov@phytec.de> > --- > arch/arm64/boot/dts/ti/Makefile | 1 + > .../boot/dts/ti/k3-am64-phycore-som.dtsi | 379 ++++++++++++++++++ > .../dts/ti/k3-am642-phyboard-electra-rdk.dts | 313 +++++++++++++++ > 3 files changed, 693 insertions(+) > create mode 100644 arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi > create mode 100644 arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts > > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile > index 4555a5be2257..79331f16cd4b 100644 > --- a/arch/arm64/boot/dts/ti/Makefile > +++ b/arch/arm64/boot/dts/ti/Makefile > @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb > dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb > > dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb > +dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb > dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb > > dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb > diff --git a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi > new file mode 100644 > index 000000000000..ecd0050a84e6 > --- /dev/null > +++ b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi > @@ -0,0 +1,379 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2021 PHYTEC America, LLC - https://www.phytec.com > + * Author: Matt McKee <mmckee@phytec.com> > + * > + * Copyright (C) 2022 PHYTEC Messtechnik GmbH > + * Author: Wadim Egorov <w.egorov@phytec.de> Here as well -> so that folks can look at the dtsi file and see where the details are? This is probably an approximate of what I'd hope to see: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=614d47cc9303893c706c0c94516249eb3adaeb80 > + */ > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/net/ti-dp83867.h> > + > +/ { > + model = "PHYTEC phyCORE-AM64x"; > + compatible = "phytec,am64-phycore-som"; Does this match the binding? > + > + aliases { > + mmc0 = &sdhci0; > + rtc0 = &rv3028; > + }; > + > + memory@80000000 { > + device_type = "memory"; > + reg = <0x00000000 0x80000000 0x00000000 0x80000000>; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + secure_ddr: optee@9e800000 { > + reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ > + alignment = <0x1000>; > + no-map; > + }; > + > + main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa0000000 0x00 0x100000>; > + no-map; > + }; > + > + main_r5fss0_core0_memory_region: r5f-memory@a0100000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa0100000 0x00 0xf00000>; > + no-map; > + }; > + > + main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa1000000 0x00 0x100000>; > + no-map; > + }; > + > + main_r5fss0_core1_memory_region: r5f-memory@a1100000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa1100000 0x00 0xf00000>; > + no-map; > + }; > + > + main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a2000000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa2000000 0x00 0x100000>; > + no-map; > + }; > + > + main_r5fss1_core0_memory_region: r5f-memory@a2100000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa2100000 0x00 0xf00000>; > + no-map; > + }; > + > + main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a3000000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa3000000 0x00 0x100000>; > + no-map; > + }; > + > + main_r5fss1_core1_memory_region: r5f-memory@a3100000 { > + compatible = "shared-dma-pool"; > + reg = <0x00 0xa3100000 0x00 0xf00000>; > + no-map; > + }; > + > + rtos_ipc_memory_region: ipc-memories@a5000000 { > + reg = <0x00 0xa5000000 0x00 0x00800000>; > + alignment = <0x1000>; > + no-map; > + }; Does this memory map work for All usage of the SoM and firmware combinations? OR would you like to keep the immutable memory map reservation in the base device tree and use overlay for firmware combination? > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&leds_pins_default>; > + > + led-green { please see the pattern property in Documentation/devicetree/bindings/leds/leds-gpio.yaml > + function = LED_FUNCTION_HEARTBEAT; > + gpios = <&main_gpio0 12 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + default-state = "on"; > + }; > + }; > + > + vcc_5v0_som: fixed-regulator-vcc-5v0-som { You would want to see feedback from Krzysztof https://lore.kernel.org/linux-arm-kernel/c40a2dad-c7aa-f778-f1ac-971185691950@linaro.org/ on the node naming. > + /* VIN / VCC_5V0_SOM */ > + compatible = "regulator-fixed"; > + regulator-name = "VCC_5V0_SOM"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + regulator-boot-on; > + }; > +}; > + [...] > + rv3028: rtc@52 { > + compatible = "microcrystal,rv3028"; > + reg = <0x52>; > + trickle-resistor-ohms = <3000>; You might want to alias rtc to make it reliably useful. If this did have an interrupt, you could potentially use it as a wakeup source for suspend states. > + }; > + > + lp8733: lp8733@61 { > + compatible = "ti,lp8733"; > + reg = <0x61>; > + > + buck0-in-supply =<&vcc_5v0_som>; > + buck1-in-supply =<&vcc_5v0_som>; > + ldo0-in-supply =<&vdd_3v3>; > + ldo1-in-supply =<&vdd_3v3>; > + > + lp8733_regulators: regulators { > + vdd_core: buck0 { See regulator comment > + regulator-name = "VDD_CORE"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + [...] > diff --git a/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts > new file mode 100644 > index 000000000000..70e34fc3592f > --- /dev/null > +++ b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts > @@ -0,0 +1,313 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2021 PHYTEC America, LLC - https://www.phytec.com > + * Author: Matt McKee <mmckee@phytec.com> > + * > + * Copyright (C) 2022 PHYTEC Messtechnik GmbH > + * Author: Wadim Egorov <w.egorov@phytec.de> Same comment for a product link as the SoM > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/leds-pca9532.h> > +#include <dt-bindings/mux/ti-serdes.h> > +#include <dt-bindings/phy/phy.h> > +#include "k3-am642.dtsi" > +#include "k3-am64-phycore-som.dtsi" > + > +/ { > + compatible = "phytec,am642-phyboard-electra-rdk", > + "phytec,am64-phycore-som", "ti,am642"; > + model = "PHYTEC phyBOARD-Electra-AM64x RDK"; > + > + aliases { > + mmc1 = &sdhci1; I plan on fixing aliases so that all aliases are defined in board device dts files, I'd suggest doing that right away in your series. https://lore.kernel.org/linux-arm-kernel/20220830201500.sowmkdyrlizpt6o2@confider/ > + }; > + > + chosen { > + stdout-path = &main_uart0; > + }; > + [...] > + > + gpio-keys { > + compatible = "gpio-keys"; > + autorepeat; > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_keys_pins_default>; > + > + key-home { > + label = "home"; > + linux,code = <KEY_HOME>; > + gpios = <&main_gpio0 17 GPIO_ACTIVE_HIGH>; > + }; > + > + key-menu { > + label = "menu"; > + linux,code = <KEY_MENU>; > + gpios = <&main_gpio0 21 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + user-leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&user_leds_pins_default>; > + > + user-led0 { Please follow the node naming pattern > + gpios = <&main_gpio0 15 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "gpio"; Please check if this matches up with the linux,default-trigger property Documentation/devicetree/bindings/leds/common.yaml > + default-state = "on"; > + }; > + > + user-led1 { > + gpios = <&main_gpio0 16 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "gpio"; > + default-state = "on"; > + }; > + }; > + > + vcc_3v3_mmc: fixed-regulator-sd { similar comment as before on regulators [...]
Am 02.11.22 um 16:10 schrieb Nishanth Menon: > On 14:49-20221102, Wadim Egorov wrote: >> Add basic support for phyBOARD-Electra-AM642. >> >> Supported features: >> * Debug UART >> * Heartbeat LED >> * GPIO buttons & LEDs >> * SPI NOR flash >> * SPI TPM Chip >> * eMMC >> * CAN >> * Ethernet >> * Micro SD card >> * I2C EEPROM >> * I2C RTC >> * LED Dimmer >> * USB > Optionally: please add a immutable link to the product (if possible > with board information and details) > > Quick scan comments below. > >> Signed-off-by: Wadim Egorov <w.egorov@phytec.de> >> --- >> arch/arm64/boot/dts/ti/Makefile | 1 + >> .../boot/dts/ti/k3-am64-phycore-som.dtsi | 379 ++++++++++++++++++ >> .../dts/ti/k3-am642-phyboard-electra-rdk.dts | 313 +++++++++++++++ >> 3 files changed, 693 insertions(+) >> create mode 100644 arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi >> create mode 100644 arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts >> >> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile >> index 4555a5be2257..79331f16cd4b 100644 >> --- a/arch/arm64/boot/dts/ti/Makefile >> +++ b/arch/arm64/boot/dts/ti/Makefile >> @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb >> dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb >> >> dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb >> +dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb >> dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb >> >> dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb >> diff --git a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi >> new file mode 100644 >> index 000000000000..ecd0050a84e6 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi >> @@ -0,0 +1,379 @@ >> +// SPDX-License-Identifier: GPL-2.0 >> +/* >> + * Copyright (C) 2021 PHYTEC America, LLC - https://www.phytec.com >> + * Author: Matt McKee <mmckee@phytec.com> >> + * >> + * Copyright (C) 2022 PHYTEC Messtechnik GmbH >> + * Author: Wadim Egorov <w.egorov@phytec.de> > Here as well -> so that folks can look at the dtsi file and see where > the details are? > > This is probably an approximate of what I'd hope to see: > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=614d47cc9303893c706c0c94516249eb3adaeb80 > >> + */ >> + >> +#include <dt-bindings/gpio/gpio.h> >> +#include <dt-bindings/leds/common.h> >> +#include <dt-bindings/net/ti-dp83867.h> >> + >> +/ { >> + model = "PHYTEC phyCORE-AM64x"; >> + compatible = "phytec,am64-phycore-som"; > Does this match the binding? Not very sure about the compatible I should chose here. It is probably not very important since the compatible gets overridden by the carrier which specifies the am642 SoC. Seems like the TI SoMs (k3-j7*som*.dtsi) do not add a compatible at all. Or do you think we should add the "ti,am642" compatible here? > >> + >> + aliases { >> + mmc0 = &sdhci0; >> + rtc0 = &rv3028; >> + }; >> + >> + memory@80000000 { >> + device_type = "memory"; >> + reg = <0x00000000 0x80000000 0x00000000 0x80000000>; >> + }; >> + >> + reserved-memory { >> + #address-cells = <2>; >> + #size-cells = <2>; >> + ranges; >> + >> + secure_ddr: optee@9e800000 { >> + reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ >> + alignment = <0x1000>; >> + no-map; >> + }; >> + >> + main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0xa0000000 0x00 0x100000>; >> + no-map; >> + }; >> + >> + main_r5fss0_core0_memory_region: r5f-memory@a0100000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0xa0100000 0x00 0xf00000>; >> + no-map; >> + }; >> + >> + main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0xa1000000 0x00 0x100000>; >> + no-map; >> + }; >> + >> + main_r5fss0_core1_memory_region: r5f-memory@a1100000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0xa1100000 0x00 0xf00000>; >> + no-map; >> + }; >> + >> + main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a2000000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0xa2000000 0x00 0x100000>; >> + no-map; >> + }; >> + >> + main_r5fss1_core0_memory_region: r5f-memory@a2100000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0xa2100000 0x00 0xf00000>; >> + no-map; >> + }; >> + >> + main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a3000000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0xa3000000 0x00 0x100000>; >> + no-map; >> + }; >> + >> + main_r5fss1_core1_memory_region: r5f-memory@a3100000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0xa3100000 0x00 0xf00000>; >> + no-map; >> + }; >> + >> + rtos_ipc_memory_region: ipc-memories@a5000000 { >> + reg = <0x00 0xa5000000 0x00 0x00800000>; >> + alignment = <0x1000>; >> + no-map; >> + }; > Does this memory map work for All usage of the SoM and firmware > combinations? OR would you like to keep the immutable memory map > reservation in the base device tree and use overlay for firmware > combination? Can you be a bit more specific about the firmware and the combinations you are talking about? For now, I just applied the same memory maps as the k3-am642-evm.dts. Are you referring to the variants of the AM64 which can come with more or less R5 cores? So an AM644 and AM641 would need different entries here and should be adjusted e.g. per dt overlays? In that case it would be nice to have a minimal set of regions defined in the som.dtsi. Regards, Wadim > >> + }; >> + >> + leds { >> + compatible = "gpio-leds"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&leds_pins_default>; >> + >> + led-green { > please see the pattern property in Documentation/devicetree/bindings/leds/leds-gpio.yaml > >> + function = LED_FUNCTION_HEARTBEAT; >> + gpios = <&main_gpio0 12 GPIO_ACTIVE_HIGH>; >> + linux,default-trigger = "heartbeat"; >> + default-state = "on"; >> + }; >> + }; >> + >> + vcc_5v0_som: fixed-regulator-vcc-5v0-som { > You would want to see feedback from Krzysztof > https://lore.kernel.org/linux-arm-kernel/c40a2dad-c7aa-f778-f1ac-971185691950@linaro.org/ > on the node naming. > >> + /* VIN / VCC_5V0_SOM */ >> + compatible = "regulator-fixed"; >> + regulator-name = "VCC_5V0_SOM"; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + regulator-always-on; >> + regulator-boot-on; >> + }; >> +}; >> + > [...] > >> + rv3028: rtc@52 { >> + compatible = "microcrystal,rv3028"; >> + reg = <0x52>; >> + trickle-resistor-ohms = <3000>; > You might want to alias rtc to make it reliably useful. If this did > have an interrupt, you could potentially use it as a wakeup source for > suspend states. > >> + }; >> + >> + lp8733: lp8733@61 { >> + compatible = "ti,lp8733"; >> + reg = <0x61>; >> + >> + buck0-in-supply =<&vcc_5v0_som>; >> + buck1-in-supply =<&vcc_5v0_som>; >> + ldo0-in-supply =<&vdd_3v3>; >> + ldo1-in-supply =<&vdd_3v3>; >> + >> + lp8733_regulators: regulators { >> + vdd_core: buck0 { > See regulator comment > >> + regulator-name = "VDD_CORE"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-boot-on; >> + regulator-always-on; >> + }; >> + > [...] > >> diff --git a/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts >> new file mode 100644 >> index 000000000000..70e34fc3592f >> --- /dev/null >> +++ b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts >> @@ -0,0 +1,313 @@ >> +// SPDX-License-Identifier: GPL-2.0 >> +/* >> + * Copyright (C) 2021 PHYTEC America, LLC - https://www.phytec.com >> + * Author: Matt McKee <mmckee@phytec.com> >> + * >> + * Copyright (C) 2022 PHYTEC Messtechnik GmbH >> + * Author: Wadim Egorov <w.egorov@phytec.de> > Same comment for a product link as the SoM > >> + */ >> + >> +/dts-v1/; >> + >> +#include <dt-bindings/gpio/gpio.h> >> +#include <dt-bindings/input/input.h> >> +#include <dt-bindings/leds/leds-pca9532.h> >> +#include <dt-bindings/mux/ti-serdes.h> >> +#include <dt-bindings/phy/phy.h> >> +#include "k3-am642.dtsi" >> +#include "k3-am64-phycore-som.dtsi" >> + >> +/ { >> + compatible = "phytec,am642-phyboard-electra-rdk", >> + "phytec,am64-phycore-som", "ti,am642"; >> + model = "PHYTEC phyBOARD-Electra-AM64x RDK"; >> + >> + aliases { >> + mmc1 = &sdhci1; > I plan on fixing aliases so that all aliases are defined in board device > dts files, I'd suggest doing that right away in your series. > > https://lore.kernel.org/linux-arm-kernel/20220830201500.sowmkdyrlizpt6o2@confider/ > >> + }; >> + >> + chosen { >> + stdout-path = &main_uart0; >> + }; >> + > [...] > >> + >> + gpio-keys { >> + compatible = "gpio-keys"; >> + autorepeat; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&gpio_keys_pins_default>; >> + >> + key-home { >> + label = "home"; >> + linux,code = <KEY_HOME>; >> + gpios = <&main_gpio0 17 GPIO_ACTIVE_HIGH>; >> + }; >> + >> + key-menu { >> + label = "menu"; >> + linux,code = <KEY_MENU>; >> + gpios = <&main_gpio0 21 GPIO_ACTIVE_HIGH>; >> + }; >> + }; >> + >> + user-leds { >> + compatible = "gpio-leds"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&user_leds_pins_default>; >> + >> + user-led0 { > Please follow the node naming pattern > >> + gpios = <&main_gpio0 15 GPIO_ACTIVE_HIGH>; >> + linux,default-trigger = "gpio"; > Please check if this matches up with the linux,default-trigger property > > Documentation/devicetree/bindings/leds/common.yaml > >> + default-state = "on"; >> + }; >> + >> + user-led1 { >> + gpios = <&main_gpio0 16 GPIO_ACTIVE_HIGH>; >> + linux,default-trigger = "gpio"; >> + default-state = "on"; >> + }; >> + }; >> + >> + vcc_3v3_mmc: fixed-regulator-sd { > similar comment as before on regulators > > [...] > >
On 16:56-20221102, Wadim Egorov wrote: [...] > >> + > >> +#include <dt-bindings/gpio/gpio.h> > >> +#include <dt-bindings/leds/common.h> > >> +#include <dt-bindings/net/ti-dp83867.h> > >> + > >> +/ { > >> + model = "PHYTEC phyCORE-AM64x"; > >> + compatible = "phytec,am64-phycore-som"; > > Does this match the binding? > > Not very sure about the compatible I should chose here. It is probably not very > important since the compatible gets overridden by the carrier which specifies > the am642 SoC. > Seems like the TI SoMs (k3-j7*som*.dtsi) do not add a compatible at all. > > Or do you think we should add the "ti,am642" compatible here? If the compatible of SoM makes much sense as a standalone OR usable elsewhere, then it could be an enum option to allow for som, soC as a valid combination. On the other hand, simplistically, it does look like SoM (like the j7es processor board) serves no specific purpose standalone, in which case skipping it is more appropriate. > >> + > >> + rtos_ipc_memory_region: ipc-memories@a5000000 { > >> + reg = <0x00 0xa5000000 0x00 0x00800000>; > >> + alignment = <0x1000>; Since it is no-map, alignment does'nt serve any purpose, right? > >> + no-map; > >> + }; > > Does this memory map work for All usage of the SoM and firmware > > combinations? OR would you like to keep the immutable memory map > > reservation in the base device tree and use overlay for firmware > > combination? > > Can you be a bit more specific about the firmware and the combinations you are > talking about? > For now, I just applied the same memory maps as the k3-am642-evm.dts. > > Are you referring to the variants of the AM64 which can come with more or less > R5 cores? > So an AM644 and AM641 would need different entries here and should be adjusted > e.g. per dt overlays? > In that case it would be nice to have a minimal set of regions defined in the > som.dtsi. Two things: In the actual usage of the board, do folks tend to stick with the memory map OR does the memory map tend to change? there are specific stuff like DM or tisci or tfa that does look mandatory. Further, if there are variations like the processor variations you mention with differing R5 combinations (processor and firmware), overlays will be your friend as it can scale across multiple carrier board options as well.
On 02/11/2022 15:41, Nishanth Menon wrote: > On 16:56-20221102, Wadim Egorov wrote: > [...] > >>>> + >>>> +#include <dt-bindings/gpio/gpio.h> >>>> +#include <dt-bindings/leds/common.h> >>>> +#include <dt-bindings/net/ti-dp83867.h> >>>> + >>>> +/ { >>>> + model = "PHYTEC phyCORE-AM64x"; >>>> + compatible = "phytec,am64-phycore-som"; >>> Does this match the binding? >> >> Not very sure about the compatible I should chose here. It is probably not very >> important since the compatible gets overridden by the carrier which specifies >> the am642 SoC. >> Seems like the TI SoMs (k3-j7*som*.dtsi) do not add a compatible at all. >> >> Or do you think we should add the "ti,am642" compatible here? > > If the compatible of SoM makes much sense as a standalone OR usable > elsewhere, then it could be an enum option to allow for som, soC as a > valid combination. > > On the other hand, simplistically, it does look like SoM (like the j7es > processor board) serves no specific purpose standalone, in which case > skipping it is more appropriate. The compatible from patch is clearly wrong - you cannot have such compatible alone. Whether having there compatible at all, is a different question... Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile index 4555a5be2257..79331f16cd4b 100644 --- a/arch/arm64/boot/dts/ti/Makefile +++ b/arch/arm64/boot/dts/ti/Makefile @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb +dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb diff --git a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi new file mode 100644 index 000000000000..ecd0050a84e6 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi @@ -0,0 +1,379 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 PHYTEC America, LLC - https://www.phytec.com + * Author: Matt McKee <mmckee@phytec.com> + * + * Copyright (C) 2022 PHYTEC Messtechnik GmbH + * Author: Wadim Egorov <w.egorov@phytec.de> + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/net/ti-dp83867.h> + +/ { + model = "PHYTEC phyCORE-AM64x"; + compatible = "phytec,am64-phycore-som"; + + aliases { + mmc0 = &sdhci0; + rtc0 = &rv3028; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x00000000 0x80000000 0x00000000 0x80000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secure_ddr: optee@9e800000 { + reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ + alignment = <0x1000>; + no-map; + }; + + main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa0000000 0x00 0x100000>; + no-map; + }; + + main_r5fss0_core0_memory_region: r5f-memory@a0100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa0100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa1000000 0x00 0x100000>; + no-map; + }; + + main_r5fss0_core1_memory_region: r5f-memory@a1100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa1100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a2000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa2000000 0x00 0x100000>; + no-map; + }; + + main_r5fss1_core0_memory_region: r5f-memory@a2100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa2100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a3000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa3000000 0x00 0x100000>; + no-map; + }; + + main_r5fss1_core1_memory_region: r5f-memory@a3100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa3100000 0x00 0xf00000>; + no-map; + }; + + rtos_ipc_memory_region: ipc-memories@a5000000 { + reg = <0x00 0xa5000000 0x00 0x00800000>; + alignment = <0x1000>; + no-map; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&leds_pins_default>; + + led-green { + function = LED_FUNCTION_HEARTBEAT; + gpios = <&main_gpio0 12 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + }; + + vcc_5v0_som: fixed-regulator-vcc-5v0-som { + /* VIN / VCC_5V0_SOM */ + compatible = "regulator-fixed"; + regulator-name = "VCC_5V0_SOM"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; +}; + +&main_pmx0 { + cpsw_mdio_pins_default: cpsw-mdio-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ + AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ + AM64X_IOPAD(0x0100, PIN_OUTPUT, 7) /* (V7) PRG1_PRU0_GPO18.GPIO0_63 */ + >; + }; + + cpsw_rgmii1_pins_default: cpsw-rgmii1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0184, PIN_INPUT, 4) /* (W6) PRG0_PRU0_GPO9.RGMII1_RX_CTL */ + AM64X_IOPAD(0x0188, PIN_INPUT, 4) /* (AA5) PRG0_PRU0_GPO10.RGMII1_RXC */ + AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */ + AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */ + AM64X_IOPAD(0x01cc, PIN_INPUT, 4) /* (W5) PRG0_PRU1_GPO7.RGMII1_RD0 */ + AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */ + AM64X_IOPAD(0x01d4, PIN_INPUT, 4) /* (Y5) PRG0_PRU1_GPO9.RGMII1_RD1 */ + AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */ + AM64X_IOPAD(0x01d8, PIN_INPUT, 4) /* (V6) PRG0_PRU1_GPO10.RGMII1_RD2 */ + AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */ + AM64X_IOPAD(0x01f4, PIN_INPUT, 4) /* (V5) PRG0_PRU1_GPO17.RGMII1_RD3 */ + AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */ + AM64X_IOPAD(0x0154, PIN_INPUT, 7) /* (V12) PRG1_PRU1_GPO19.GPIO0_84 */ + >; + }; + + eeprom_wp_pins_default: eeprom-wp-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0208, PIN_OUTPUT, 7) /* (D12) SPI0_CS0.GPIO1_42 */ + >; + }; + + leds_pins_default: leds-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0030, PIN_OUTPUT, 7) /* (L18) OSPI0_CSn1.GPIO0_12 */ + >; + }; + + main_i2c0_pins_default: main-i2c0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0260, PIN_INPUT, 0) /* (A18) I2C0_SCL */ + AM64X_IOPAD(0x0264, PIN_INPUT, 0) /* (B18) I2C0_SDA */ + >; + }; + + ospi0_pins_default: ospi0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* (N20) OSPI0_CLK */ + AM64X_IOPAD(0x0008, PIN_INPUT, 0) /* (N19) OSPI0_DQS */ + AM64X_IOPAD(0x000c, PIN_INPUT, 0) /* (M19) OSPI0_D0 */ + AM64X_IOPAD(0x0010, PIN_INPUT, 0) /* (M18) OSPI0_D1 */ + AM64X_IOPAD(0x0014, PIN_INPUT, 0) /* (M20) OSPI0_D2 */ + AM64X_IOPAD(0x0018, PIN_INPUT, 0) /* (M21) OSPI0_D3 */ + AM64X_IOPAD(0x001c, PIN_INPUT, 0) /* (P21) OSPI0_D4 */ + AM64X_IOPAD(0x0020, PIN_INPUT, 0) /* (P20) OSPI0_D5 */ + AM64X_IOPAD(0x0024, PIN_INPUT, 0) /* (N18) OSPI0_D6 */ + AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* (M17) OSPI0_D7 */ + AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */ + >; + }; +}; + +&cpsw3g { + pinctrl-names = "default"; + pinctrl-0 = <&cpsw_rgmii1_pins_default>; +}; + +&cpsw3g_mdio { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cpsw_mdio_pins_default>; + + cpsw3g_phy1: ethernet-phy@1 { + compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22"; + reg = <1>; + interrupt-parent = <&main_gpio0>; + interrupts = <84 IRQ_TYPE_EDGE_FALLING>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + reset-gpios = <&main_gpio0 63 GPIO_ACTIVE_LOW>; + reset-assert-us = <1000>; + reset-deassert-us = <1000>; + }; +}; + +&cpsw_port1 { + phy-mode = "rgmii-rxid"; + phy-handle = <&cpsw3g_phy1>; +}; + +&cpsw_port2 { + status = "disabled"; +}; + +&mailbox0_cluster2 { + mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 { + ti,mbox-rx = <0 0 2>; + ti,mbox-tx = <1 0 2>; + }; + + mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 { + ti,mbox-rx = <2 0 2>; + ti,mbox-tx = <3 0 2>; + }; +}; + +&mailbox0_cluster3 { + status = "disabled"; +}; + +&mailbox0_cluster4 { + mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 { + ti,mbox-rx = <0 0 2>; + ti,mbox-tx = <1 0 2>; + }; + + mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 { + ti,mbox-rx = <2 0 2>; + ti,mbox-tx = <3 0 2>; + }; +}; + +&mailbox0_cluster5 { + status = "disabled"; +}; + +&mailbox0_cluster6 { + mbox_m4_0: mbox-m4-0 { + ti,mbox-rx = <0 0 2>; + ti,mbox-tx = <1 0 2>; + }; +}; + +&mailbox0_cluster7 { + status = "disabled"; +}; + +&main_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + + eeprom@50 { + compatible = "atmel,24c32"; + pinctrl-names = "default"; + pinctrl-0 = <&eeprom_wp_pins_default>; + pagesize = <32>; + reg = <0x50>; + }; + + rv3028: rtc@52 { + compatible = "microcrystal,rv3028"; + reg = <0x52>; + trickle-resistor-ohms = <3000>; + }; + + lp8733: lp8733@61 { + compatible = "ti,lp8733"; + reg = <0x61>; + + buck0-in-supply =<&vcc_5v0_som>; + buck1-in-supply =<&vcc_5v0_som>; + ldo0-in-supply =<&vdd_3v3>; + ldo1-in-supply =<&vdd_3v3>; + + lp8733_regulators: regulators { + vdd_core: buck0 { + regulator-name = "VDD_CORE"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd_3v3: buck1 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd_1v8_ldo0: ldo0 { + regulator-name = "VDD_1V8_LDO0"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + vdda_1v8: ldo1 { + regulator-name = "VDDA_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&main_r5fss0_core0 { + mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core0>; + memory-region = <&main_r5fss0_core0_dma_memory_region>, + <&main_r5fss0_core0_memory_region>; +}; + +&main_r5fss0_core1 { + mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core1>; + memory-region = <&main_r5fss0_core1_dma_memory_region>, + <&main_r5fss0_core1_memory_region>; +}; + +&main_r5fss1_core0 { + mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core0>; + memory-region = <&main_r5fss1_core0_dma_memory_region>, + <&main_r5fss1_core0_memory_region>; +}; + +&main_r5fss1_core1 { + mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core1>; + memory-region = <&main_r5fss1_core1_dma_memory_region>, + <&main_r5fss1_core1_memory_region>; +}; + +/* mcu_gpio0 is reserved for mcu firmware usage */ +&mcu_gpio0 { + status = "reserved"; +}; + +&ospi0 { + pinctrl-names = "default"; + pinctrl-0 = <&ospi0_pins_default>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <8>; + spi-rx-bus-width = <8>; + spi-max-frequency = <25000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <0>; + }; +}; + +&sdhci0 { + bus-width = <8>; + non-removable; + ti,driver-strength-ohm = <50>; + disable-wp; + keep-power-in-suspend; +}; + +/* adc0 is reserved for R5 usage */ +&tscadc0 { + status = "reserved"; +}; diff --git a/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts new file mode 100644 index 000000000000..70e34fc3592f --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts @@ -0,0 +1,313 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 PHYTEC America, LLC - https://www.phytec.com + * Author: Matt McKee <mmckee@phytec.com> + * + * Copyright (C) 2022 PHYTEC Messtechnik GmbH + * Author: Wadim Egorov <w.egorov@phytec.de> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/leds-pca9532.h> +#include <dt-bindings/mux/ti-serdes.h> +#include <dt-bindings/phy/phy.h> +#include "k3-am642.dtsi" +#include "k3-am64-phycore-som.dtsi" + +/ { + compatible = "phytec,am642-phyboard-electra-rdk", + "phytec,am64-phycore-som", "ti,am642"; + model = "PHYTEC phyBOARD-Electra-AM64x RDK"; + + aliases { + mmc1 = &sdhci1; + }; + + chosen { + stdout-path = &main_uart0; + }; + + can_tc1: can-phy0 { + compatible = "ti,tcan1042"; + pinctrl-names = "default"; + pinctrl-0 = <&can_tc1_pins_default>; + #phy-cells = <0>; + max-bitrate = <5000000>; + standby-gpios = <&main_gpio0 32 GPIO_ACTIVE_HIGH>; + }; + + can_tc2: can-phy1 { + compatible = "ti,tcan1042"; + pinctrl-names = "default"; + pinctrl-0 = <&can_tc2_pins_default>; + #phy-cells = <0>; + max-bitrate = <5000000>; + standby-gpios = <&main_gpio0 35 GPIO_ACTIVE_HIGH>; + }; + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_pins_default>; + + key-home { + label = "home"; + linux,code = <KEY_HOME>; + gpios = <&main_gpio0 17 GPIO_ACTIVE_HIGH>; + }; + + key-menu { + label = "menu"; + linux,code = <KEY_MENU>; + gpios = <&main_gpio0 21 GPIO_ACTIVE_HIGH>; + }; + }; + + user-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&user_leds_pins_default>; + + user-led0 { + gpios = <&main_gpio0 15 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "gpio"; + default-state = "on"; + }; + + user-led1 { + gpios = <&main_gpio0 16 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "gpio"; + default-state = "on"; + }; + }; + + vcc_3v3_mmc: fixed-regulator-sd { + /* TPS22963C */ + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3_MMC"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; +}; + +&main_pmx0 { + can_tc1_pins_default: can-tc1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0084, PIN_OUTPUT, 7) /* (P16) GPMC0_ADVn_ALE.GPIO0_32 */ + >; + }; + + can_tc2_pins_default: can-tc2-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0090, PIN_OUTPUT, 7) /* (P17) GPMC0_BE0n_CLE.GPIO0_35 */ + >; + }; + + gpio_keys_pins_default: gpio-keys-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0044, PIN_INPUT, 7) /* (T18) GPMC0_AD2.GPIO0_17 */ + AM64X_IOPAD(0x0054, PIN_INPUT, 7) /* (V20) GPMC0_AD6.GPIO0_21 */ + >; + }; + + main_i2c1_pins_default: main-i2c1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0268, PIN_INPUT, 0) /* (C18) I2C1_SCL */ + AM64X_IOPAD(0x026c, PIN_INPUT, 0) /* (B19) I2C1_SDA */ + >; + }; + + main_mcan0_pins_default: main-mcan0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0250, PIN_OUTPUT, 0) /* (A17) MCAN0_TX */ + AM64X_IOPAD(0x0254, PIN_INPUT, 0) /* (B17) MCAN0_RX */ + >; + }; + + main_mcan1_pins_default: main-mcan1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (C17) MCAN1_TX */ + AM64X_IOPAD(0x025c, PIN_INPUT, 0) /* (D17) MCAN1_RX */ + >; + }; + + main_mmc1_pins_default: main-mmc1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */ + AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */ + AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */ + AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */ + AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */ + AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* MMC1_CLKLB */ + AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ + AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */ + >; + }; + + main_spi0_pins_default: main-spi0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x020c, PIN_OUTPUT, 7) /* (C13) SPI0_CS1.GPIO1_43 */ + AM64X_IOPAD(0x0210, PIN_INPUT, 0) /* (D13) SPI0_CLK */ + AM64X_IOPAD(0x0214, PIN_OUTPUT, 0) /* (A13) SPI0_D0 */ + AM64X_IOPAD(0x0218, PIN_INPUT, 0) /* (A14) SPI0_D1 */ + >; + }; + + main_uart0_pins_default: main-uart0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */ + AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */ + >; + }; + + main_uart1_pins_default: main-uart1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ + AM64X_IOPAD(0x024C, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ + AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */ + AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ + >; + }; + + main_usb0_pins_default: main-usb0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ + >; + }; + + pcie_usb_sel_pins_default: pcie-usb-sel-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x017c, PIN_OUTPUT, 7) /* (T1) PRG0_PRU0_GPO7.GPIO1_7 */ + >; + }; + + pcie0_pins_default: pcie0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0098, PIN_OUTPUT, 7) /* (W19) GPMC0_WAIT0.GPIO0_37 */ + >; + }; + + user_leds_pins_default: user-leds-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x003c, PIN_OUTPUT, 7) /* (T20) GPMC0_AD0.GPIO0_15 */ + AM64X_IOPAD(0x0040, PIN_OUTPUT, 7) /* (U21) GPMC0_AD1.GPIO0_16 */ + >; + }; +}; + +&main_i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_pins_default>; + clock-frequency = <400000>; + + eeprom@51 { + compatible = "atmel,24c02"; + pagesize = <16>; + reg = <0x51>; + }; + + pca9533d: led-dimmer@62 { + compatible = "nxp,pca9533"; + reg = <0x62>; + + rgb-red { + type = <PCA9532_TYPE_LED>; + default-state = "on"; + }; + + rgb-green { + type = <PCA9532_TYPE_LED>; + default-state = "on"; + }; + + rgb-blue { + type = <PCA9532_TYPE_LED>; + default-state = "on"; + }; + }; +}; + +&main_mcan0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_mcan0_pins_default>; + phys = <&can_tc1>; +}; + +&main_mcan1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_mcan1_pins_default>; + phys = <&can_tc2>; +}; + +&main_spi0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_spi0_pins_default>; + cs-gpios = <0>, <&main_gpio1 43 GPIO_ACTIVE_LOW>; + ti,pindir-d0-out-d1-in; + + slb9670: tpm20@1 { + compatible = "infineon,slb9670"; + reg = <1>; + spi-max-frequency = <10000000>; + }; +}; + +&main_uart0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart0_pins_default>; +}; + +&main_uart1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart1_pins_default>; + uart-has-rtscts; +}; + +&sdhci1 { + vmmc-supply = <&vcc_3v3_mmc>; + pinctrl-names = "default"; + pinctrl-0 = <&main_mmc1_pins_default>; + bus-width = <4>; + ti,driver-strength-ohm = <50>; + disable-wp; + no-1-8-v; +}; + +&serdes0 { + serdes0_pcie_usb_link: phy@0 { + reg = <0>; + cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_USB3>; + resets = <&serdes_wiz0 1>; + }; +}; + +&serdes_ln_ctrl { + idle-states = <AM64_SERDES0_LANE0_USB>; +}; + +&usbss0 { + ti,vbus-divider; +}; + +&usb0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_usb0_pins_default>; + dr_mode = "host"; + maximum-speed = "super-speed"; + phys = <&serdes0_pcie_usb_link>; + phy-names = "cdns3,usb3-phy"; +};
Add basic support for phyBOARD-Electra-AM642. Supported features: * Debug UART * Heartbeat LED * GPIO buttons & LEDs * SPI NOR flash * SPI TPM Chip * eMMC * CAN * Ethernet * Micro SD card * I2C EEPROM * I2C RTC * LED Dimmer * USB Signed-off-by: Wadim Egorov <w.egorov@phytec.de> --- arch/arm64/boot/dts/ti/Makefile | 1 + .../boot/dts/ti/k3-am64-phycore-som.dtsi | 379 ++++++++++++++++++ .../dts/ti/k3-am642-phyboard-electra-rdk.dts | 313 +++++++++++++++ 3 files changed, 693 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi create mode 100644 arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts