@@ -112,6 +112,11 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-thor96.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-eval.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-ixora-v1.1.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-v1.1-eval.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-v1.1-ixora-v1.1.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-v1.1-ixora-v1.2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qm-mek.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-eval-v3.dtb
new file mode 100644
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+ aliases {
+ rtc0 = &rtc_i2c;
+ rtc1 = &rtc;
+ };
+
+ reg_usb_host_vbus: regulator-usb-host-vbus {
+ regulator-name = "VCC USBH2(ABCD) / USBH(3|4)";
+ };
+};
+
+&adc0 {
+ status = "okay";
+};
+
+&adc1 {
+ status = "okay";
+};
+
+/* TODO: Audio Mixer */
+
+/* TODO: Asynchronous Sample Rate Converter (ASRC) */
+
+/* TODO: Display Controller */
+
+/* TODO: DPU */
+
+/* Apalis ETH1 */
+&fec1 {
+ status = "okay";
+};
+
+/* TODO: CAN */
+
+/* TODO: GPU */
+
+/* Apalis I2C1 */
+&i2c2 {
+ status = "okay";
+
+ atmel_mxt_ts: touch@4a {
+ compatible = "atmel,maxtouch";
+ interrupt-parent = <&lsio_gpio4>;
+ interrupts = <1 IRQ_TYPE_EDGE_FALLING>; /* Apalis GPIO5 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio5>, <&pinctrl_gpio6>;
+ reg = <0x4a>;
+ reset-gpios = <&lsio_gpio4 2 GPIO_ACTIVE_LOW>; /* Apalis GPIO6 */
+ status = "disabled";
+ };
+
+ /* M41T0M6 real time clock on carrier board */
+ rtc_i2c: rtc@68 {
+ compatible = "st,m41t0";
+ reg = <0x68>;
+ };
+};
+
+/* Apalis I2C3 (CAM) */
+&i2c3 {
+ status = "okay";
+};
+
+/* Apalis SPI1 */
+&lpspi0 {
+ status = "okay";
+};
+
+/* Apalis SPI2 */
+&lpspi2 {
+ status = "okay";
+};
+
+/* Apalis UART3 */
+&lpuart0 {
+ status = "okay";
+};
+
+/* Apalis UART1 */
+&lpuart1 {
+ status = "okay";
+};
+
+/* Apalis UART4 */
+&lpuart2 {
+ status = "okay";
+};
+
+/* Apalis UART2 */
+&lpuart3 {
+ status = "okay";
+};
+
+/* Apalis PWM3, MXM3 pin 6 */
+&lsio_pwm0 {
+ status = "okay";
+};
+
+/* Apalis PWM4, MXM3 pin 8 */
+&lsio_pwm1 {
+ status = "okay";
+};
+
+/* Apalis PWM1, MXM3 pin 2 */
+&lsio_pwm2 {
+ status = "okay";
+};
+
+/* Apalis PWM2, MXM3 pin 4 */
+&lsio_pwm3 {
+ status = "okay";
+};
+
+/* TODO: Apalis PCIE1 */
+
+/* TODO: Apalis BKL1_PWM */
+
+/* TODO: Apalis DAP1 */
+
+/* TODO: Apalis SATA1 */
+
+/* TODO: Apalis SPDIF1 */
+
+/* TODO: Apalis USBH2, Apalis USBH3 and on-module Wi-Fi via on-module HSIC Hub */
+
+/* Apalis USBO1 */
+&usbotg1 {
+ status = "okay";
+};
+
+/* TODO: Apalis USBH4 SuperSpeed */
+
+/* Apalis MMC1 */
+&usdhc2 {
+ status = "okay";
+};
+
+/* Apalis SD1 */
+&usdhc3 {
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+ aliases {
+ rtc0 = &rtc_i2c;
+ rtc1 = &rtc;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds_ixora>;
+
+ /* MXM3_188 */
+ led4-green {
+ label = "LED_4_GREEN";
+ gpios = <&lsio_gpio5 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* MXM3_178 */
+ led4-red {
+ label = "LED_4_RED";
+ gpios = <&lsio_gpio5 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* MXM3_152 */
+ led5-green {
+ label = "LED_5_GREEN";
+ gpios = <&lsio_gpio5 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* MXM3_156 */
+ led5-red {
+ label = "LED_5_RED";
+ gpios = <&lsio_gpio5 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_usb_host_vbus: regulator-usb-host-vbus {
+ regulator-name = "VCC_USBH(2|4)";
+ };
+};
+
+&adc0 {
+ status = "okay";
+};
+
+&adc1 {
+ status = "okay";
+};
+
+/* TODO: Audio Mixer */
+
+/* TODO: Asynchronous Sample Rate Converter (ASRC) */
+
+/* TODO: Display Controller */
+
+/* TODO: DPU */
+
+/* Apalis ETH1 */
+&fec1 {
+ status = "okay";
+};
+
+/* TODO: CAN */
+
+/* TODO: GPU */
+
+/* Apalis I2C1 */
+&i2c2 {
+ status = "okay";
+
+ atmel_mxt_ts: touch@4a {
+ compatible = "atmel,maxtouch";
+ interrupt-parent = <&lsio_gpio4>;
+ interrupts = <1 IRQ_TYPE_EDGE_FALLING>; /* Apalis GPIO5 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio5>, <&pinctrl_gpio6>;
+ reg = <0x4a>;
+ reset-gpios = <&lsio_gpio4 2 GPIO_ACTIVE_LOW>; /* Apalis GPIO6 */
+ status = "disabled";
+ };
+
+ /* M41T0M6 real time clock on carrier board */
+ rtc_i2c: rtc@68 {
+ compatible = "st,m41t0";
+ reg = <0x68>;
+ };
+};
+
+/* Apalis I2C3 (CAM) */
+&i2c3 {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-0 = <&pinctrl_cam1_gpios>, <&pinctrl_dap1_gpios>,
+ <&pinctrl_esai0_gpios>, <&pinctrl_fec2_gpios>,
+ <&pinctrl_gpio3>, <&pinctrl_gpio4>, <&pinctrl_gpio_usbh_oc_n>,
+ <&pinctrl_lpuart1ctrl>, <&pinctrl_lvds0_i2c0_gpio>,
+ <&pinctrl_lvds1_i2c0_gpios>, <&pinctrl_mipi_dsi_0_1_en>,
+ <&pinctrl_mipi_dsi1_gpios>, <&pinctrl_mlb_gpios>,
+ <&pinctrl_qspi1a_gpios>, <&pinctrl_sata1_act>,
+ <&pinctrl_sim0_gpios>, <&pinctrl_uart24_forceoff>,
+ <&pinctrl_usdhc1_gpios>;
+
+ pinctrl_leds_ixora: ledsixoragrp {
+ fsl,pins =
+ <IMX8QM_USDHC2_DATA1_LSIO_GPIO5_IO27 0x06000061>, /* LED_4_GREEN */
+ <IMX8QM_USDHC2_DATA3_LSIO_GPIO5_IO29 0x06000061>, /* LED_4_RED */
+ <IMX8QM_USDHC1_DATA5_LSIO_GPIO5_IO20 0x06000061>, /* LED_5_GREEN */
+ <IMX8QM_USDHC1_DATA6_LSIO_GPIO5_IO21 0x06000061>; /* LED_5_RED */
+ };
+
+ pinctrl_uart24_forceoff: uart24forceoffgrp {
+ fsl,pins =
+ <IMX8QM_USDHC2_CMD_LSIO_GPIO5_IO25 0x00000021>;
+ };
+};
+
+/* Apalis SPI1 */
+&lpspi0 {
+ status = "okay";
+};
+
+/* Apalis SPI2 */
+&lpspi2 {
+ status = "okay";
+};
+
+/* Apalis UART3 */
+&lpuart0 {
+ status = "okay";
+};
+
+/* Apalis UART1 */
+&lpuart1 {
+ status = "okay";
+};
+
+/* Apalis UART4 */
+&lpuart2 {
+ status = "okay";
+};
+
+/* Apalis UART2 */
+&lpuart3 {
+ status = "okay";
+};
+
+&lsio_gpio5 {
+ ngpios = <32>;
+ gpio-line-names = "gpio5-00", "gpio5-01", "gpio5-02", "gpio5-03",
+ "gpio5-04", "gpio5-05", "gpio5-06", "gpio5-07",
+ "gpio5-08", "gpio5-09", "gpio5-10", "gpio5-11",
+ "gpio5-12", "gpio5-13", "gpio5-14", "gpio5-15",
+ "gpio5-16", "gpio5-17", "gpio5-18", "gpio5-19",
+ "LED-5-GREEN", "LED-5-RED", "gpio5-22", "gpio5-23",
+ "gpio5-24", "UART24-FORCEOFF", "gpio5-26",
+ "LED-4-GREEN", "gpio5-28", "LED-4-RED", "gpio5-30",
+ "gpio5-31";
+};
+
+/* Apalis PWM3, MXM3 pin 6 */
+&lsio_pwm0 {
+ status = "okay";
+};
+
+/* Apalis PWM4, MXM3 pin 8 */
+&lsio_pwm1 {
+ status = "okay";
+};
+
+/* Apalis PWM1, MXM3 pin 2 */
+&lsio_pwm2 {
+ status = "okay";
+};
+
+/* Apalis PWM2, MXM3 pin 4 */
+&lsio_pwm3 {
+ status = "okay";
+};
+
+/* TODO: Apalis PCIE1 */
+
+/* TODO: Apalis BKL1_PWM */
+
+/* TODO: Apalis DAP1 */
+
+/* TODO: Apalis SATA1 */
+
+/* TODO: Apalis SPDIF1 */
+
+/* TODO: Apalis USBH2, Apalis USBH3 and on-module Wi-Fi via on-module HSIC Hub */
+
+/* Apalis USBO1 */
+&usbotg1 {
+ status = "okay";
+};
+
+/* TODO: Apalis USBH4 SuperSpeed */
+
+/* Apalis MMC1 */
+&usdhc2 {
+ bus-width = <4>;
+ pinctrl-0 = <&pinctrl_usdhc2_4bit>, <&pinctrl_mmc1_cd>;
+ pinctrl-1 = <&pinctrl_usdhc2_4bit_100mhz>, <&pinctrl_mmc1_cd>;
+ pinctrl-2 = <&pinctrl_usdhc2_4bit_200mhz>, <&pinctrl_mmc1_cd>;
+ pinctrl-3 = <&pinctrl_usdhc2_4bit_sleep>, <&pinctrl_mmc1_cd_sleep>;
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,264 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+ aliases {
+ rtc0 = &rtc_i2c;
+ rtc1 = &rtc;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds_ixora>;
+
+ /* MXM3_188 */
+ led4-green {
+ label = "LED_4_GREEN";
+ gpios = <&lsio_gpio5 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* MXM3_178 */
+ led4-red {
+ label = "LED_4_RED";
+ gpios = <&lsio_gpio5 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* MXM3_152 */
+ led5-green {
+ label = "LED_5_GREEN";
+ gpios = <&lsio_gpio5 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* MXM3_156 */
+ led5-red {
+ label = "LED_5_RED";
+ gpios = <&lsio_gpio5 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_3v3_vmmc: regulator-3v3-vmmc {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ /* MMC1_PWR_CTRL */
+ gpio = <&lsio_gpio5 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_3v3_vmmc>;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "3v3_vmmc";
+ };
+
+ reg_can1_supply: regulator-can1-supply {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&lsio_gpio5 22 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_can1_power>;
+ regulator-name = "can1_supply";
+ };
+
+ reg_can2_supply: regulator-can2-supply {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&lsio_gpio2 8 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sata1_act>;
+ regulator-name = "can2_supply";
+ };
+
+ reg_usb_host_vbus: regulator-usb-host-vbus {
+ regulator-name = "VCC_USBH(2|4)";
+ };
+};
+
+&adc0 {
+ status = "okay";
+};
+
+&adc1 {
+ status = "okay";
+};
+
+/* TODO: Audio Mixer */
+
+/* TODO: Asynchronous Sample Rate Converter (ASRC) */
+
+/* TODO: Display Controller */
+
+/* TODO: DPU */
+
+/* Apalis ETH1 */
+&fec1 {
+ status = "okay";
+};
+
+/* TODO: CAN */
+
+/* TODO: GPU */
+
+/* Apalis I2C1 */
+&i2c2 {
+ status = "okay";
+
+ atmel_mxt_ts: touch@4a {
+ compatible = "atmel,maxtouch";
+ interrupt-parent = <&lsio_gpio4>;
+ interrupts = <1 IRQ_TYPE_EDGE_FALLING>; /* Apalis GPIO5 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio5>, <&pinctrl_gpio6>;
+ reg = <0x4a>;
+ reset-gpios = <&lsio_gpio4 2 GPIO_ACTIVE_LOW>; /* Apalis GPIO6 */
+ status = "disabled";
+ };
+
+ /* M41T0M6 real time clock on carrier board */
+ rtc_i2c: rtc@68 {
+ compatible = "st,m41t0";
+ reg = <0x68>;
+ };
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c02";
+ pagesize = <16>;
+ reg = <0x50>;
+ };
+};
+
+/* Apalis I2C3 (CAM) */
+&i2c3 {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-0 = <&pinctrl_cam1_gpios>, <&pinctrl_dap1_gpios>,
+ <&pinctrl_esai0_gpios>, <&pinctrl_fec2_gpios>,
+ <&pinctrl_gpio3>, <&pinctrl_gpio4>, <&pinctrl_gpio_usbh_oc_n>,
+ <&pinctrl_lpuart1ctrl>, <&pinctrl_lvds0_i2c0_gpio>,
+ <&pinctrl_lvds1_i2c0_gpios>, <&pinctrl_mipi_dsi_0_1_en>,
+ <&pinctrl_mipi_dsi1_gpios>, <&pinctrl_mlb_gpios>,
+ <&pinctrl_qspi1a_gpios>, <&pinctrl_sim0_gpios>,
+ <&pinctrl_uart24_forceoff>, <&pinctrl_usdhc1_gpios>;
+
+ /* PMIC MMC1 power-switch */
+ pinctrl_enable_3v3_vmmc: enable3v3vmmcgrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_DATA4_LSIO_GPIO5_IO19 0x00000021>; /* MXM3_148, PMIC */
+ };
+
+ /* FlexCAN PMIC */
+ pinctrl_enable_can1_power: enablecan1powergrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_DATA7_LSIO_GPIO5_IO22 0x00000021>; /* MXM3_158, PMIC */
+ };
+
+ pinctrl_leds_ixora: ledsixoragrp {
+ fsl,pins =
+ <IMX8QM_USDHC2_DATA1_LSIO_GPIO5_IO27 0x06000061>, /* LED_4_GREEN */
+ <IMX8QM_USDHC2_DATA3_LSIO_GPIO5_IO29 0x06000061>, /* LED_4_RED */
+ <IMX8QM_USDHC1_DATA5_LSIO_GPIO5_IO20 0x06000061>, /* LED_5_GREEN */
+ <IMX8QM_USDHC1_DATA6_LSIO_GPIO5_IO21 0x06000061>; /* LED_5_RED */
+ };
+
+ pinctrl_uart24_forceoff: uart24forceoffgrp {
+ fsl,pins =
+ <IMX8QM_USDHC2_CMD_LSIO_GPIO5_IO25 0x00000021>;
+ };
+};
+
+/* Apalis SPI1 */
+&lpspi0 {
+ status = "okay";
+};
+
+/* Apalis SPI2 */
+&lpspi2 {
+ status = "okay";
+};
+
+/* Apalis UART3 */
+&lpuart0 {
+ status = "okay";
+};
+
+/* Apalis UART1 */
+&lpuart1 {
+ status = "okay";
+};
+
+/* Apalis UART4 */
+&lpuart2 {
+ status = "okay";
+};
+
+/* Apalis UART2 */
+&lpuart3 {
+ status = "okay";
+};
+
+&lsio_gpio5 {
+ ngpios = <32>;
+ gpio-line-names = "gpio5-00", "gpio5-01", "gpio5-02", "gpio5-03",
+ "gpio5-04", "gpio5-05", "gpio5-06", "gpio5-07",
+ "gpio5-08", "gpio5-09", "gpio5-10", "gpio5-11",
+ "gpio5-12", "gpio5-13", "gpio5-14", "gpio5-15",
+ "gpio5-16", "gpio5-17", "gpio5-18", "gpio5-19",
+ "LED-5-GREEN", "LED-5-RED", "gpio5-22", "gpio5-23",
+ "gpio5-24", "UART24-FORCEOFF", "gpio5-26",
+ "LED-4-GREEN", "gpio5-28", "LED-4-RED", "gpio5-30",
+ "gpio5-31";
+};
+
+/* Apalis PWM3, MXM3 pin 6 */
+&lsio_pwm0 {
+ status = "okay";
+};
+
+/* Apalis PWM4, MXM3 pin 8 */
+&lsio_pwm1 {
+ status = "okay";
+};
+
+/* Apalis PWM1, MXM3 pin 2 */
+&lsio_pwm2 {
+ status = "okay";
+};
+
+/* Apalis PWM2, MXM3 pin 4 */
+&lsio_pwm3 {
+ status = "okay";
+};
+
+/* TODO: Apalis PCIE1 */
+
+/* TODO: Apalis BKL1_PWM */
+
+/* TODO: Apalis DAP1 */
+
+/* TODO: Apalis SATA1 */
+
+/* TODO: Apalis SPDIF1 */
+
+/* TODO: Apalis USBH2, Apalis USBH3 and on-module Wi-Fi via on-module HSIC Hub */
+
+/* Apalis USBO1 */
+&usbotg1 {
+ status = "okay";
+};
+
+/* TODO: Apalis USBH4 SuperSpeed */
+
+/* Apalis MMC1 */
+&usdhc2 {
+ bus-width = <4>;
+ cap-power-off-card;
+ /delete-property/ no-1-8-v;
+ pinctrl-0 = <&pinctrl_usdhc2_4bit>, <&pinctrl_mmc1_cd>;
+ pinctrl-1 = <&pinctrl_usdhc2_4bit_100mhz>, <&pinctrl_mmc1_cd>;
+ pinctrl-2 = <&pinctrl_usdhc2_4bit_200mhz>, <&pinctrl_mmc1_cd>;
+ pinctrl-3 = <&pinctrl_usdhc2_4bit_sleep>, <&pinctrl_mmc1_cd_sleep>;
+ vmmc-supply = <®_3v3_vmmc>;
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,1510 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ chosen {
+ stdout-path = &lpuart1;
+ };
+
+ /* Apalis BKL1 */
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 45 63 88 119 158 203 255>;
+ default-brightness-level = <4>;
+ enable-gpios = <&lsio_gpio1 4 GPIO_ACTIVE_HIGH>; /* Apalis BKL1_ON */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_bkl_on>;
+ /* TODO: hook-up to Apalis BKL1_PWM */
+ status = "disabled";
+ };
+
+ gpio_fan: gpio-fan {
+ compatible = "gpio-fan";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio8>;
+ gpios = <&lsio_gpio3 28 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = < 0 0
+ 3000 1>;
+ };
+
+/* TODO: LVDS Panel */
+
+/* TODO: Shared PCIe/SATA Reference Clock */
+
+/* TODO: PCIe Wi-Fi Reference Clock */
+
+ /*
+ * Power management bus used to control LDO1OUT of the
+ * second PMIC PF8100. This is used for controlling voltage levels of
+ * typespecific RGMII signals and Apalis UART2_RTS UART2_CTS.
+ *
+ * IMX_SC_R_BOARD_R1 for 3.3V
+ * IMX_SC_R_BOARD_R2 for 1.8V
+ * IMX_SC_R_BOARD_R3 for 2.5V
+ * Note that for 2.5V operation the pad muxing needs to be changed,
+ * compare with PSW_OVR field of IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD.
+ *
+ * those power domains are mutually exclusive.
+ */
+ reg_ext_rgmii: regulator-ext-rgmii {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_EXT_RGMII (LDO1)";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ power-domains = <&pd IMX_SC_R_BOARD_R1>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ reg_module_3v3: regulator-module-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_module_3v3_avdd: regulator-module-3v3-avdd {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3_AUDIO";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_module_wifi: regulator-module-wifi {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&lsio_gpio1 28 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_pdn>;
+ regulator-name = "wifi_pwrdn_fake_regulator";
+ regulator-settling-time-us = <100>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ reg_pcie_switch: regulator-pcie-switch {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio7>;
+ enable-active-high;
+ gpio = <&lsio_gpio3 26 GPIO_ACTIVE_HIGH>;
+ regulator-name = "pcie_switch";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us = <100000>;
+ };
+
+ reg_usb_host_vbus: regulator-usb-host-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh_en>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ /* Apalis USBH_EN */
+ gpio = <&lsio_gpio4 4 GPIO_ACTIVE_HIGH>;
+ regulator-always-on;
+ };
+
+ reg_usb_hsic: regulator-usb-hsic {
+ compatible = "regulator-fixed";
+ regulator-name = "usb-hsic-dummy";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ reg_usb_phy: regulator-usb-hsic1 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb-phy-dummy";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ reg_vref_1v8: regulator-vref-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "+V1.8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ decoder_boot: decoder_boot@84000000 {
+ no-map;
+ reg = <0 0x84000000 0 0x2000000>;
+ };
+
+ encoder1_boot: encoder1_boot@86000000 {
+ no-map;
+ reg = <0 0x86000000 0 0x200000>;
+ };
+
+ encoder2_boot: encoder2_boot@86200000 {
+ no-map;
+ reg = <0 0x86200000 0 0x200000>;
+ };
+
+ /*
+ * reserved-memory layout
+ * 0x8800_0000 ~ 0x8FFF_FFFF is reserved for M4
+ * Shouldn't be used at A core and Linux side.
+ *
+ */
+ m4_reserved: m4@88000000 {
+ no-map;
+ reg = <0 0x88000000 0 0x8000000>;
+ };
+
+ rpmsg_reserved: rpmsg@90000000 {
+ no-map;
+ reg = <0 0x90200000 0 0x200000>;
+ };
+
+ vdevbuffer: vdevbuffer@90400000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x90400000 0 0x100000>;
+ no-map;
+ };
+
+ decoder_rpc: decoder_rpc@92000000 {
+ no-map;
+ reg = <0 0x92000000 0 0x200000>;
+ };
+
+ dsp_reserved: dsp@92400000 {
+ no-map;
+ reg = <0 0x92400000 0 0x2000000>;
+ };
+
+ encoder1_rpc: encoder1_rpc@94400000 {
+ no-map;
+ reg = <0 0x94400000 0 0x700000>;
+ };
+
+ encoder2_rpc: encoder2_rpc@94b00000 {
+ no-map;
+ reg = <0 0x94b00000 0 0x700000>;
+ };
+
+ /* global autoconfigured region for contiguous allocations */
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ size = <0 0x3c000000>;
+ alloc-ranges = <0 0xc0000000 0 0x3c000000>;
+ linux,cma-default;
+ };
+ };
+
+ /* TODO: Apalis Analogue Audio */
+
+ /* TODO: HDMI Audio */
+
+ /* TODO: Apalis SPDIF1 */
+
+ touchscreen: vf50-touchscreen {
+ compatible = "toradex,vf50-touchscreen";
+ io-channels = <&adc1 2>,<&adc1 1>,
+ <&adc1 0>,<&adc1 3>;
+ interrupt-parent = <&lsio_gpio3>;
+ interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "idle","default";
+ pinctrl-0 = <&pinctrl_touchctrl_idle>, <&pinctrl_touchctrl_gpios>;
+ pinctrl-1 = <&pinctrl_adc1>, <&pinctrl_touchctrl_gpios>;
+ vf50-ts-min-pressure = <200>;
+ xp-gpios = <&lsio_gpio2 4 GPIO_ACTIVE_LOW>;
+ xm-gpios = <&lsio_gpio2 5 GPIO_ACTIVE_HIGH>;
+ yp-gpios = <&lsio_gpio2 17 GPIO_ACTIVE_LOW>;
+ ym-gpios = <&lsio_gpio2 21 GPIO_ACTIVE_HIGH>;
+ /*
+ * NOTE: you must remove the pinctrl-adc1 from the adc1
+ * node below to use the touchscreen
+ */
+ status = "disabled";
+ };
+
+};
+
+&adc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0>;
+ vref-supply = <®_vref_1v8>;
+};
+
+&adc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc1>;
+ vref-supply = <®_vref_1v8>;
+};
+
+/* TODO: Asynchronous Sample Rate Converter (ASRC) */
+
+/* Apalis ETH1 */
+&fec1 {
+ fsl,magic-packet;
+ phy-handle = <ðphy0>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pinctrl_fec1>;
+ pinctrl-1 = <&pinctrl_fec1_sleep>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@7 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ interrupt-parent = <&lsio_gpio1>;
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+ micrel,led-mode = <0>;
+ reg = <7>;
+ reset-assert-us = <2>;
+ reset-deassert-us = <2>;
+ reset-gpios = <&lsio_gpio1 11 GPIO_ACTIVE_LOW>;
+ reset-names = "phy-reset";
+ };
+ };
+};
+
+/* TODO: Apalis CAN1 (driver upstream but device tree part missing) */
+
+/* TODO: Apalis CAN2 (driver upstream but device tree part missing) */
+
+/* TODO: Apalis CAN3 (optional, driver upstream but device tree part missing) */
+
+/* TODO: Apalis HDMI1 */
+
+/* On-module I2C */
+&i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c1>;
+ status = "okay";
+
+ /* TODO: Audio Codec */
+
+ /* USB3503A */
+ usb3503@8 {
+ compatible = "smsc,usb3503a";
+ connect-gpios = <&lsio_gpio0 31 GPIO_ACTIVE_LOW>;
+ initial-mode = <1>;
+ intn-gpios = <&lsio_gpio1 1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb3503a>;
+ refclk-frequency = <25000000>;
+ reg = <0x08>;
+ reset-gpios = <&lsio_gpio1 2 GPIO_ACTIVE_LOW>;
+ };
+};
+
+/* Apalis I2C1 */
+&i2c2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c2>;
+};
+
+/* Apalis I2C3 (CAM) */
+&i2c3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c3>;
+};
+
+&jpegdec {
+ status = "okay";
+};
+
+&jpegenc {
+ status = "okay";
+};
+
+/* TODO: Apalis LVDS1 */
+
+/* Apalis SPI1 */
+&lpspi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cs-gpios = <&lsio_gpio3 5 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpspi0>;
+};
+
+/* Apalis SPI2 */
+&lpspi2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cs-gpios = <&lsio_gpio3 10 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpspi2>;
+};
+
+/* Apalis UART3 */
+&lpuart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart0>;
+};
+
+/* Apalis UART1 */
+&lpuart1 {
+ dma-names = "","";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart1>;
+};
+
+/* Apalis UART4 */
+&lpuart2 {
+ dma-names = "","";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart2>;
+};
+
+/* Apalis UART2 */
+&lpuart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart3>;
+};
+
+&lsio_gpio0 {
+ gpio-line-names = "MXM3_279",
+ "MXM3_277",
+ "MXM3_135",
+ "MXM3_203",
+ "MXM3_201",
+ "MXM3_275",
+ "MXM3_110",
+ "MXM3_120",
+ "MXM3_1/GPIO1",
+ "MXM3_3/GPIO2",
+ "MXM3_124",
+ "MXM3_122",
+ "MXM3_5/GPIO3",
+ "MXM3_7/GPIO4",
+ "",
+ "",
+ "MXM3_4",
+ "MXM3_211",
+ "MXM3_209",
+ "MXM3_2",
+ "MXM3_136",
+ "MXM3_134",
+ "MXM3_6",
+ "MXM3_8",
+ "MXM3_112",
+ "MXM3_118",
+ "MXM3_114",
+ "MXM3_116";
+};
+
+&lsio_gpio1 {
+ gpio-line-names = "",
+ "",
+ "",
+ "",
+ "MXM3_286",
+ "",
+ "MXM3_87",
+ "MXM3_99",
+ "MXM3_138",
+ "MXM3_140",
+ "MXM3_239",
+ "",
+ "MXM3_281",
+ "MXM3_283",
+ "MXM3_126",
+ "MXM3_132",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_173",
+ "MXM3_175",
+ "MXM3_123";
+
+ hdmi-ctrl-hog {
+ gpio-hog;
+ gpios = <30 GPIO_ACTIVE_HIGH>;
+ line-name = "CONNECTOR_IS_HDMI";
+ /* Set signals depending on HDP device type, 0 DP, 1 HDMI */
+ output-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi_ctrl>;
+ };
+};
+
+&lsio_gpio2 {
+ gpio-line-names = "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_198",
+ "MXM3_35",
+ "MXM3_164",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_217",
+ "MXM3_215",
+ "",
+ "",
+ "MXM3_193",
+ "MXM3_194",
+ "MXM3_37",
+ "",
+ "MXM3_271",
+ "MXM3_273",
+ "MXM3_195",
+ "MXM3_197",
+ "MXM3_177",
+ "MXM3_179",
+ "MXM3_181",
+ "MXM3_183",
+ "MXM3_185",
+ "MXM3_187";
+
+ /*
+ * Add GPIO2_20 as a wakeup source:
+ * Pin: 101 SC_P_SPI3_CS0 (MXM3_37/WAKE1_MICO)
+ * Type: 5 SC_PAD_WAKEUP_FALL_EDGE
+ * Line: 20
+ */
+ pad-wakeup = <IMX8QM_SPI3_CS0 5 20>;
+ pad-wakeup-num = <1>;
+
+ pcie_wifi_hog {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ line-name = "PCIE_WIFI_CLK";
+ output-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie_wifi_refclk>;
+ };
+};
+
+&lsio_gpio3 {
+ gpio-line-names = "MXM3_191",
+ "",
+ "MXM3_221",
+ "MXM3_225",
+ "MXM3_223",
+ "MXM3_227",
+ "MXM3_200",
+ "MXM3_235",
+ "MXM3_231",
+ "MXM3_229",
+ "MXM3_233",
+ "MXM3_204",
+ "MXM3_196",
+ "",
+ "MXM3_202",
+ "",
+ "",
+ "",
+ "MXM3_305",
+ "MXM3_307",
+ "MXM3_309",
+ "MXM3_311",
+ "MXM3_315",
+ "MXM3_317",
+ "MXM3_319",
+ "MXM3_321",
+ "MXM3_15/GPIO7",
+ "MXM3_63",
+ "MXM3_17/GPIO8",
+ "MXM3_12",
+ "MXM3_14",
+ "MXM3_16";
+};
+
+&lsio_gpio4 {
+ gpio-line-names = "MXM3_18",
+ "MXM3_11/GPIO5",
+ "MXM3_13/GPIO6",
+ "MXM3_274",
+ "MXM3_84",
+ "MXM3_262",
+ "MXM3_96",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_190",
+ "",
+ "",
+ "",
+ "MXM3_269",
+ "MXM3_251",
+ "MXM3_253",
+ "MXM3_295",
+ "MXM3_299",
+ "MXM3_301",
+ "MXM3_297",
+ "MXM3_293",
+ "MXM3_291",
+ "MXM3_289",
+ "MXM3_287";
+
+ /* Enable pcie root / sata ref clock unconditionally */
+ pcie_sata_hog {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ line-name = "PCIE_SATA_CLK";
+ output-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie_sata_refclk>;
+ };
+};
+
+&lsio_gpio5 {
+ gpio-line-names = "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_150",
+ "MXM3_160",
+ "MXM3_162",
+ "MXM3_144",
+ "MXM3_146",
+ "MXM3_148",
+ "MXM3_152",
+ "MXM3_156",
+ "MXM3_158",
+ "MXM3_159",
+ "MXM3_184",
+ "MXM3_180",
+ "MXM3_186",
+ "MXM3_188",
+ "MXM3_176",
+ "MXM3_178";
+};
+
+&lsio_gpio6 {
+ gpio-line-names = "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_261",
+ "MXM3_263",
+ "MXM3_259",
+ "MXM3_257",
+ "MXM3_255",
+ "MXM3_128",
+ "MXM3_130",
+ "MXM3_265",
+ "MXM3_249",
+ "MXM3_247",
+ "MXM3_245",
+ "MXM3_243";
+};
+
+/* Apalis PWM3, MXM3 pin 6 */
+&lsio_pwm0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0>;
+ #pwm-cells = <3>;
+};
+
+/* Apalis PWM4, MXM3 pin 8 */
+&lsio_pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ #pwm-cells = <3>;
+};
+
+/* Apalis PWM1, MXM3 pin 2 */
+&lsio_pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ #pwm-cells = <3>;
+};
+
+/* Apalis PWM2, MXM3 pin 4 */
+&lsio_pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ #pwm-cells = <3>;
+};
+
+/* TODO: Messaging Units */
+
+/* TODO: Apalis PCIE1 */
+
+/* TODO: On-module Wi-Fi */
+
+/* TODO: Apalis BKL1_PWM */
+
+/* TODO: Apalis DAP1 */
+
+/* TODO: Apalis SATA1 */
+
+/* TODO: Apalis SPDIF1 */
+
+/* TODO: Thermal Zones */
+
+/* TODO: Apalis USBH2, Apalis USBH3 and on-module Wi-Fi via on-module HSIC Hub */
+
+/* TODO: Apalis USBH4 */
+
+/* Apalis USBO1 */
+&usbphy1 {
+ phy-3p0-supply = <®_usb_phy>;
+ status = "okay";
+};
+
+&usbotg1 {
+ adp-disable;
+ ci-disable-lpm;
+ hnp-disable;
+ over-current-active-low;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ power-active-high;
+ srp-disable;
+};
+
+/* On-module eMMC */
+&usdhc1 {
+ bus-width = <8>;
+ non-removable;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ status = "okay";
+};
+
+/* Apalis MMC1 */
+&usdhc2 {
+ bus-width = <8>;
+ cd-gpios = <&lsio_gpio2 9 GPIO_ACTIVE_LOW>; /* Apalis MMC1_CD# */
+ no-1-8-v;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+ pinctrl-0 = <&pinctrl_usdhc2_4bit>,
+ <&pinctrl_usdhc2_8bit>,
+ <&pinctrl_mmc1_cd>;
+ pinctrl-1 = <&pinctrl_usdhc2_4bit_100mhz>,
+ <&pinctrl_usdhc2_8bit_100mhz>,
+ <&pinctrl_mmc1_cd>;
+ pinctrl-2 = <&pinctrl_usdhc2_4bit_200mhz>,
+ <&pinctrl_usdhc2_8bit_200mhz>,
+ <&pinctrl_mmc1_cd>;
+ pinctrl-3 = <&pinctrl_usdhc2_4bit_sleep>,
+ <&pinctrl_usdhc2_8bit_sleep>,
+ <&pinctrl_mmc1_cd_sleep>;
+};
+
+/* Apalis SD1 */
+&usdhc3 {
+ bus-width = <4>;
+ cd-gpios = <&lsio_gpio4 12 GPIO_ACTIVE_LOW>; /* Apalis SD1_CD# */
+ no-1-8-v;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_sd1_cd>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_sd1_cd>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_sd1_cd>;
+};
+
+/* TODO: Video Processing Unit (driver upstream but device tree part missing) */
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cam1_gpios>, <&pinctrl_dap1_gpios>,
+ <&pinctrl_esai0_gpios>, <&pinctrl_fec2_gpios>,
+ <&pinctrl_gpio3>, <&pinctrl_gpio4>, <&pinctrl_gpio_keys>,
+ <&pinctrl_gpio_usbh_oc_n>, <&pinctrl_lpuart1ctrl>,
+ <&pinctrl_lvds0_i2c0_gpio>, <&pinctrl_lvds1_i2c0_gpios>,
+ <&pinctrl_mipi_dsi_0_1_en>, <&pinctrl_mipi_dsi1_gpios>,
+ <&pinctrl_mlb_gpios>, <&pinctrl_qspi1a_gpios>,
+ <&pinctrl_sata1_act>, <&pinctrl_sim0_gpios>,
+ <&pinctrl_usdhc1_gpios>;
+
+ /* Apalis AN1_ADC */
+ pinctrl_adc0: adc0grp {
+ fsl,pins =
+ /* Apalis AN1_ADC0 */
+ <IMX8QM_ADC_IN0_DMA_ADC0_IN0 0xc0000060>,
+ /* Apalis AN1_ADC1 */
+ <IMX8QM_ADC_IN1_DMA_ADC0_IN1 0xc0000060>,
+ /* Apalis AN1_ADC2 */
+ <IMX8QM_ADC_IN2_DMA_ADC0_IN2 0xc0000060>,
+ /* Apalis AN1_TSWIP_ADC3 */
+ <IMX8QM_ADC_IN3_DMA_ADC0_IN3 0xc0000060>;
+ };
+
+ /* Apalis AN1_TS */
+ pinctrl_adc1: adc1grp {
+ fsl,pins =
+ /* Apalis AN1_TSPX */
+ <IMX8QM_ADC_IN4_DMA_ADC1_IN0 0xc0000060>,
+ /* Apalis AN1_TSMX */
+ <IMX8QM_ADC_IN5_DMA_ADC1_IN1 0xc0000060>,
+ /* Apalis AN1_TSPY */
+ <IMX8QM_ADC_IN6_DMA_ADC1_IN2 0xc0000060>,
+ /* Apalis AN1_TSMY */
+ <IMX8QM_ADC_IN7_DMA_ADC1_IN3 0xc0000060>;
+ };
+
+ /* Apalis CAM1 */
+ pinctrl_cam1_gpios: cam1gpiosgrp {
+ fsl,pins =
+ /* Apalis CAM1_D7 */
+ <IMX8QM_MIPI_DSI1_I2C0_SCL_LSIO_GPIO1_IO20 0x00000021>,
+ /* Apalis CAM1_D6 */
+ <IMX8QM_MIPI_DSI1_I2C0_SDA_LSIO_GPIO1_IO21 0x00000021>,
+ /* Apalis CAM1_D5 */
+ <IMX8QM_ESAI0_TX0_LSIO_GPIO2_IO26 0x00000021>,
+ /* Apalis CAM1_D4 */
+ <IMX8QM_ESAI0_TX1_LSIO_GPIO2_IO27 0x00000021>,
+ /* Apalis CAM1_D3 */
+ <IMX8QM_ESAI0_TX2_RX3_LSIO_GPIO2_IO28 0x00000021>,
+ /* Apalis CAM1_D2 */
+ <IMX8QM_ESAI0_TX3_RX2_LSIO_GPIO2_IO29 0x00000021>,
+ /* Apalis CAM1_D1 */
+ <IMX8QM_ESAI0_TX4_RX1_LSIO_GPIO2_IO30 0x00000021>,
+ /* Apalis CAM1_D0 */
+ <IMX8QM_ESAI0_TX5_RX0_LSIO_GPIO2_IO31 0x00000021>,
+ /* Apalis CAM1_PCLK */
+ <IMX8QM_MCLK_IN0_LSIO_GPIO3_IO00 0x00000021>,
+ /* Apalis CAM1_MCLK */
+ <IMX8QM_SPI3_SDO_LSIO_GPIO2_IO18 0x00000021>,
+ /* Apalis CAM1_VSYNC */
+ <IMX8QM_ESAI0_SCKR_LSIO_GPIO2_IO24 0x00000021>,
+ /* Apalis CAM1_HSYNC */
+ <IMX8QM_ESAI0_SCKT_LSIO_GPIO2_IO25 0x00000021>;
+ };
+
+ /* Apalis DAP1 */
+ pinctrl_dap1_gpios: dap1gpiosgrp {
+ fsl,pins =
+ /* Apalis DAP1_MCLK */
+ <IMX8QM_SPI3_SDI_LSIO_GPIO2_IO19 0x00000021>,
+ /* Apalis DAP1_D_OUT */
+ <IMX8QM_SAI1_RXC_LSIO_GPIO3_IO12 0x00000021>,
+ /* Apalis DAP1_RESET */
+ <IMX8QM_ESAI1_SCKT_LSIO_GPIO2_IO07 0x00000021>,
+ /* Apalis DAP1_BIT_CLK */
+ <IMX8QM_SPI0_CS1_LSIO_GPIO3_IO06 0x00000021>,
+ /* Apalis DAP1_D_IN */
+ <IMX8QM_SAI1_RXFS_LSIO_GPIO3_IO14 0x00000021>,
+ /* Apalis DAP1_SYNC */
+ <IMX8QM_SPI2_CS1_LSIO_GPIO3_IO11 0x00000021>,
+ /* On-module Wi-Fi_I2S_EN# */
+ <IMX8QM_ESAI1_TX5_RX0_LSIO_GPIO2_IO13 0x00000021>;
+ };
+
+ /* Apalis LCD1_G1+2 */
+ pinctrl_esai0_gpios: esai0gpiosgrp {
+ fsl,pins =
+ /* Apalis LCD1_G1 */
+ <IMX8QM_ESAI0_FSR_LSIO_GPIO2_IO22 0x00000021>,
+ /* Apalis LCD1_G2 */
+ <IMX8QM_ESAI0_FST_LSIO_GPIO2_IO23 0x00000021>;
+ };
+
+ /* On-module Gigabit Ethernet PHY Micrel KSZ9031 for Apalis GLAN */
+ pinctrl_fec1: fec1grp {
+ fsl,pins =
+ /* Use pads in 3.3V mode */
+ <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD 0x000014a0>,
+ <IMX8QM_ENET0_MDC_CONN_ENET0_MDC 0x06000020>,
+ <IMX8QM_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x06000020>,
+ <IMX8QM_ENET0_REFCLK_125M_25M_CONN_ENET0_REFCLK_125M_25M 0x06000020>,
+ /* On-module ETH_RESET# */
+ <IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11 0x06000020>,
+ /* On-module ETH_INT# */
+ <IMX8QM_MIPI_CSI1_MCLK_OUT_LSIO_GPIO1_IO29 0x04000060>;
+ };
+
+ pinctrl_fec1_sleep: fec1-sleepgrp {
+ fsl,pins =
+ <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD 0x000014a0>,
+ <IMX8QM_ENET0_MDC_LSIO_GPIO4_IO14 0x04000040>,
+ <IMX8QM_ENET0_MDIO_LSIO_GPIO4_IO13 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TX_CTL_LSIO_GPIO5_IO31 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TXC_LSIO_GPIO5_IO30 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TXD0_LSIO_GPIO6_IO00 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TXD1_LSIO_GPIO6_IO01 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TXD2_LSIO_GPIO6_IO02 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TXD3_LSIO_GPIO6_IO03 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RXC_LSIO_GPIO6_IO04 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RX_CTL_LSIO_GPIO6_IO05 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RXD0_LSIO_GPIO6_IO06 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RXD1_LSIO_GPIO6_IO07 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RXD2_LSIO_GPIO6_IO08 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RXD3_LSIO_GPIO6_IO09 0x04000040>,
+ <IMX8QM_ENET0_REFCLK_125M_25M_LSIO_GPIO4_IO15 0x04000040>,
+ <IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11 0x06000020>,
+ <IMX8QM_MIPI_CSI1_MCLK_OUT_LSIO_GPIO1_IO29 0x04000040>;
+ };
+
+ /* Apalis LCD1_ */
+ pinctrl_fec2_gpios: fec2gpiosgrp {
+ fsl,pins =
+ <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD 0x000014a0>,
+ /* Apalis LCD1_R1 */
+ <IMX8QM_ENET1_MDC_LSIO_GPIO4_IO18 0x00000021>,
+ /* Apalis LCD1_R0 */
+ <IMX8QM_ENET1_MDIO_LSIO_GPIO4_IO17 0x00000021>,
+ /* Apalis LCD1_G0 */
+ <IMX8QM_ENET1_REFCLK_125M_25M_LSIO_GPIO4_IO16 0x00000021>,
+ /* Apalis LCD1_R7 */
+ <IMX8QM_ENET1_RGMII_RX_CTL_LSIO_GPIO6_IO17 0x00000021>,
+ /* Apalis LCD1_DE */
+ <IMX8QM_ENET1_RGMII_RXD0_LSIO_GPIO6_IO18 0x00000021>,
+ /* Apalis LCD1_HSYNC */
+ <IMX8QM_ENET1_RGMII_RXD1_LSIO_GPIO6_IO19 0x00000021>,
+ /* Apalis LCD1_VSYNC */
+ <IMX8QM_ENET1_RGMII_RXD2_LSIO_GPIO6_IO20 0x00000021>,
+ /* Apalis LCD1_PCLK */
+ <IMX8QM_ENET1_RGMII_RXD3_LSIO_GPIO6_IO21 0x00000021>,
+ /* Apalis LCD1_R6 */
+ <IMX8QM_ENET1_RGMII_TX_CTL_LSIO_GPIO6_IO11 0x00000021>,
+ /* Apalis LCD1_R5 */
+ <IMX8QM_ENET1_RGMII_TXC_LSIO_GPIO6_IO10 0x00000021>,
+ /* Apalis LCD1_R4 */
+ <IMX8QM_ENET1_RGMII_TXD0_LSIO_GPIO6_IO12 0x00000021>,
+ /* Apalis LCD1_R3 */
+ <IMX8QM_ENET1_RGMII_TXD1_LSIO_GPIO6_IO13 0x00000021>,
+ /* Apalis LCD1_R2 */
+ <IMX8QM_ENET1_RGMII_TXD2_LSIO_GPIO6_IO14 0x00000021>;
+ };
+
+ /* Apalis CAN1 */
+ pinctrl_flexcan1: flexcan0grp {
+ fsl,pins =
+ <IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX 0x00000021>,
+ <IMX8QM_FLEXCAN0_RX_DMA_FLEXCAN0_RX 0x00000021>;
+ };
+
+ /* Apalis CAN2 */
+ pinctrl_flexcan2: flexcan1grp {
+ fsl,pins =
+ <IMX8QM_FLEXCAN1_TX_DMA_FLEXCAN1_TX 0x00000021>,
+ <IMX8QM_FLEXCAN1_RX_DMA_FLEXCAN1_RX 0x00000021>;
+ };
+
+ /* Apalis CAN3 (optional) */
+ pinctrl_flexcan3: flexcan2grp {
+ fsl,pins =
+ <IMX8QM_FLEXCAN2_TX_DMA_FLEXCAN2_TX 0x00000021>,
+ <IMX8QM_FLEXCAN2_RX_DMA_FLEXCAN2_RX 0x00000021>;
+ };
+
+ /* Apalis GPIO1 */
+ pinctrl_gpio1: gpio1grp {
+ fsl,pins =
+ <IMX8QM_M40_GPIO0_00_LSIO_GPIO0_IO08 0x06000021>;
+ };
+
+ /* Apalis GPIO2 */
+ pinctrl_gpio2: gpio2grp {
+ fsl,pins =
+ <IMX8QM_M40_GPIO0_01_LSIO_GPIO0_IO09 0x06000021>;
+ };
+
+ /* Apalis GPIO3 */
+ pinctrl_gpio3: gpio3grp {
+ fsl,pins =
+ <IMX8QM_M41_GPIO0_00_LSIO_GPIO0_IO12 0x06000021>;
+ };
+
+ /* Apalis GPIO4 */
+ pinctrl_gpio4: gpio4grp {
+ fsl,pins =
+ <IMX8QM_M41_GPIO0_01_LSIO_GPIO0_IO13 0x06000021>;
+ };
+
+ /* Apalis GPIO5 */
+ pinctrl_gpio5: gpio5grp {
+ fsl,pins =
+ <IMX8QM_FLEXCAN2_RX_LSIO_GPIO4_IO01 0x06000021>;
+ };
+
+ /* Apalis GPIO6 */
+ pinctrl_gpio6: gpio6grp {
+ fsl,pins =
+ <IMX8QM_FLEXCAN2_TX_LSIO_GPIO4_IO02 0x00000021>;
+ };
+
+ /* Apalis GPIO7 */
+ pinctrl_gpio7: gpio7grp {
+ fsl,pins =
+ <IMX8QM_MLB_SIG_LSIO_GPIO3_IO26 0x00000021>;
+ };
+
+ /* Apalis GPIO8 */
+ pinctrl_gpio8: gpio8grp {
+ fsl,pins =
+ <IMX8QM_MLB_DATA_LSIO_GPIO3_IO28 0x00000021>;
+ };
+
+ /* Apalis BKL1_ON */
+ pinctrl_gpio_bkl_on: gpiobklongrp {
+ fsl,pins =
+ <IMX8QM_LVDS0_GPIO00_LSIO_GPIO1_IO04 0x00000021>;
+ };
+
+ /* Apalis WAKE1_MICO */
+ pinctrl_gpio_keys: gpiokeysgrp {
+ fsl,pins =
+ <IMX8QM_SPI3_CS0_LSIO_GPIO2_IO20 0x06700021>;
+ };
+
+ /* Apalis USBH_OC# */
+ pinctrl_gpio_usbh_oc_n: gpiousbhocngrp {
+ fsl,pins =
+ <IMX8QM_USB_SS3_TC3_LSIO_GPIO4_IO06 0x04000021>;
+ };
+
+ /* On-module HDMI_CTRL */
+ pinctrl_hdmi_ctrl: hdmictrlgrp {
+ fsl,pins =
+ <IMX8QM_MIPI_CSI1_GPIO0_00_LSIO_GPIO1_IO30 0x00000061>;
+ };
+
+ /* On-module I2C */
+ pinctrl_lpi2c1: lpi2c1grp {
+ fsl,pins =
+ <IMX8QM_GPT0_CLK_DMA_I2C1_SCL 0x04000020>,
+ <IMX8QM_GPT0_CAPTURE_DMA_I2C1_SDA 0x04000020>;
+ };
+
+ /* Apalis I2C1 */
+ pinctrl_lpi2c2: lpi2c2grp {
+ fsl,pins =
+ <IMX8QM_GPT1_CLK_DMA_I2C2_SCL 0x04000020>,
+ <IMX8QM_GPT1_CAPTURE_DMA_I2C2_SDA 0x04000020>;
+ };
+
+ /* Apalis I2C3 (CAM) */
+ pinctrl_lpi2c3: lpi2c3grp {
+ fsl,pins =
+ <IMX8QM_SIM0_PD_DMA_I2C3_SCL 0x04000020>,
+ <IMX8QM_SIM0_POWER_EN_DMA_I2C3_SDA 0x04000020>;
+ };
+
+ /* Apalis SPI1 */
+ pinctrl_lpspi0: lpspi0grp {
+ fsl,pins =
+ <IMX8QM_SPI0_SCK_DMA_SPI0_SCK 0x0600004c>,
+ <IMX8QM_SPI0_SDO_DMA_SPI0_SDO 0x0600004c>,
+ <IMX8QM_SPI0_SDI_DMA_SPI0_SDI 0x0600004c>,
+ <IMX8QM_SPI0_CS0_LSIO_GPIO3_IO05 0x0600004c>;
+ };
+
+ /* Apalis SPI2 */
+ pinctrl_lpspi2: lpspi2grp {
+ fsl,pins =
+ <IMX8QM_SPI2_SCK_DMA_SPI2_SCK 0x0600004c>,
+ <IMX8QM_SPI2_SDO_DMA_SPI2_SDO 0x0600004c>,
+ <IMX8QM_SPI2_SDI_DMA_SPI2_SDI 0x0600004c>,
+ <IMX8QM_SPI2_CS0_LSIO_GPIO3_IO10 0x0600004c>;
+ };
+
+ /* Apalis UART3 */
+ pinctrl_lpuart0: lpuart0grp {
+ fsl,pins =
+ <IMX8QM_UART0_RX_DMA_UART0_RX 0x06000020>,
+ <IMX8QM_UART0_TX_DMA_UART0_TX 0x06000020>;
+ };
+
+ /* Apalis UART1 */
+ pinctrl_lpuart1: lpuart1grp {
+ fsl,pins =
+ <IMX8QM_UART1_RX_DMA_UART1_RX 0x06000020>,
+ <IMX8QM_UART1_TX_DMA_UART1_TX 0x06000020>,
+ <IMX8QM_UART1_CTS_B_DMA_UART1_CTS_B 0x06000020>,
+ <IMX8QM_UART1_RTS_B_DMA_UART1_RTS_B 0x06000020>;
+ };
+
+ /* Apalis UART1 */
+ pinctrl_lpuart1ctrl: lpuart1ctrlgrp {
+ fsl,pins =
+ /* Apalis UART1_DTR */
+ <IMX8QM_M40_I2C0_SCL_LSIO_GPIO0_IO06 0x00000021>,
+ /* Apalis UART1_DSR */
+ <IMX8QM_M40_I2C0_SDA_LSIO_GPIO0_IO07 0x00000021>,
+ /* Apalis UART1_DCD */
+ <IMX8QM_M41_I2C0_SCL_LSIO_GPIO0_IO10 0x00000021>,
+ /* Apalis UART1_RI */
+ <IMX8QM_M41_I2C0_SDA_LSIO_GPIO0_IO11 0x00000021>;
+ };
+
+ /* Apalis UART4 */
+ pinctrl_lpuart2: lpuart2grp {
+ fsl,pins =
+ <IMX8QM_LVDS0_I2C1_SCL_DMA_UART2_TX 0x06000020>,
+ <IMX8QM_LVDS0_I2C1_SDA_DMA_UART2_RX 0x06000020>;
+ };
+
+ /* Apalis UART2 */
+ pinctrl_lpuart3: lpuart3grp {
+ fsl,pins =
+ <IMX8QM_LVDS1_I2C1_SCL_DMA_UART3_TX 0x06000020>,
+ <IMX8QM_LVDS1_I2C1_SDA_DMA_UART3_RX 0x06000020>,
+ <IMX8QM_ENET1_RGMII_TXD3_DMA_UART3_RTS_B 0x06000020>,
+ <IMX8QM_ENET1_RGMII_RXC_DMA_UART3_CTS_B 0x06000020>;
+ };
+
+ /* Apalis TS_2 */
+ pinctrl_lvds0_i2c0_gpio: lvds0i2c0gpiogrp {
+ fsl,pins =
+ <IMX8QM_LVDS0_I2C0_SCL_LSIO_GPIO1_IO06 0x00000021>;
+ };
+
+ /* Apalis LCD1_G6+7 */
+ pinctrl_lvds1_i2c0_gpios: lvds1i2c0gpiosgrp {
+ fsl,pins =
+ /* Apalis LCD1_G6 */
+ <IMX8QM_LVDS1_I2C0_SCL_LSIO_GPIO1_IO12 0x00000021>,
+ /* Apalis LCD1_G7 */
+ <IMX8QM_LVDS1_I2C0_SDA_LSIO_GPIO1_IO13 0x00000021>;
+ };
+
+ /* Apalis TS_3 */
+ pinctrl_mipi_dsi_0_1_en: mipidsi0-1engrp {
+ fsl,pins =
+ <IMX8QM_LVDS0_I2C0_SDA_LSIO_GPIO1_IO07 0x00000021>;
+ };
+
+ /* Apalis TS_4 */
+ pinctrl_mipi_dsi1_gpios: mipidsi1gpiosgrp {
+ fsl,pins =
+ <IMX8QM_MIPI_DSI1_GPIO0_00_LSIO_GPIO1_IO22 0x00000021>;
+ };
+
+ /* Apalis TS_1 */
+ pinctrl_mlb_gpios: mlbgpiosgrp {
+ fsl,pins =
+ <IMX8QM_MLB_CLK_LSIO_GPIO3_IO27 0x00000021>;
+ };
+
+ /* Apalis MMC1_CD# */
+ pinctrl_mmc1_cd: mmc1cdgrp {
+ fsl,pins =
+ <IMX8QM_ESAI1_TX1_LSIO_GPIO2_IO09 0x00000021>;
+ };
+
+ pinctrl_mmc1_cd_sleep: mmc1cdsleepgrp {
+ fsl,pins =
+ <IMX8QM_ESAI1_TX1_LSIO_GPIO2_IO09 0x04000021>;
+ };
+
+ /* On-module PCIe_Wi-Fi */
+ pinctrl_pcieb: pciebgrp {
+ fsl,pins =
+ <IMX8QM_PCIE_CTRL1_CLKREQ_B_LSIO_GPIO4_IO30 0x00000021>,
+ <IMX8QM_PCIE_CTRL1_WAKE_B_LSIO_GPIO4_IO31 0x00000021>,
+ <IMX8QM_PCIE_CTRL1_PERST_B_LSIO_GPIO5_IO00 0x00000021>;
+ };
+
+ /* On-module PCIe_CLK_EN1 */
+ pinctrl_pcie_sata_refclk: pciesatarefclkgrp {
+ fsl,pins =
+ <IMX8QM_USDHC2_WP_LSIO_GPIO4_IO11 0x00000021>;
+ };
+
+ /* On-module PCIe_CLK_EN2 */
+ pinctrl_pcie_wifi_refclk: pciewifirefclkgrp {
+ fsl,pins =
+ <IMX8QM_ESAI1_TX3_RX2_LSIO_GPIO2_IO11 0x00000021>;
+ };
+
+ /* Apalis PWM3 */
+ pinctrl_pwm0: pwm0grp {
+ fsl,pins =
+ <IMX8QM_UART0_RTS_B_LSIO_PWM0_OUT 0x00000020>;
+ };
+
+ /* Apalis PWM4 */
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins =
+ <IMX8QM_UART0_CTS_B_LSIO_PWM1_OUT 0x00000020>;
+ };
+
+ /* Apalis PWM1 */
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins =
+ <IMX8QM_GPT1_COMPARE_LSIO_PWM2_OUT 0x00000020>;
+ };
+
+ /* Apalis PWM2 */
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins =
+ <IMX8QM_GPT0_COMPARE_LSIO_PWM3_OUT 0x00000020>;
+ };
+
+ /* Apalis BKL1_PWM */
+ pinctrl_pwm_bkl: pwmbklgrp {
+ fsl,pins =
+ <IMX8QM_LVDS1_GPIO00_LVDS1_PWM0_OUT 0x00000020>;
+ };
+
+ /* Apalis LCD1_ */
+ pinctrl_qspi1a_gpios: qspi1agpiosgrp {
+ fsl,pins =
+ /* Apalis LCD1_B0 */
+ <IMX8QM_QSPI1A_DATA0_LSIO_GPIO4_IO26 0x00000021>,
+ /* Apalis LCD1_B1 */
+ <IMX8QM_QSPI1A_DATA1_LSIO_GPIO4_IO25 0x00000021>,
+ /* Apalis LCD1_B2 */
+ <IMX8QM_QSPI1A_DATA2_LSIO_GPIO4_IO24 0x00000021>,
+ /* Apalis LCD1_B3 */
+ <IMX8QM_QSPI1A_DATA3_LSIO_GPIO4_IO23 0x00000021>,
+ /* Apalis LCD1_B5 */
+ <IMX8QM_QSPI1A_DQS_LSIO_GPIO4_IO22 0x00000021>,
+ /* Apalis LCD1_B7 */
+ <IMX8QM_QSPI1A_SCLK_LSIO_GPIO4_IO21 0x00000021>,
+ /* Apalis LCD1_B4 */
+ <IMX8QM_QSPI1A_SS0_B_LSIO_GPIO4_IO19 0x00000021>,
+ /* Apalis LCD1_B6 */
+ <IMX8QM_QSPI1A_SS1_B_LSIO_GPIO4_IO20 0x00000021>;
+ };
+
+ /* On-module RESET_MOCI#_DRV */
+ pinctrl_reset_moci: resetmocigrp {
+ fsl,pins =
+ <IMX8QM_SCU_GPIO0_02_LSIO_GPIO0_IO30 0x00000021>;
+ };
+
+ /* On-module I2S SGTL5000 for Apalis Analogue Audio */
+ pinctrl_sai1: sai1grp {
+ fsl,pins =
+ <IMX8QM_SAI1_TXD_AUD_SAI1_TXD 0xc600006c>,
+ <IMX8QM_SAI1_RXD_AUD_SAI1_RXD 0xc600004c>,
+ <IMX8QM_SAI1_TXC_AUD_SAI1_TXC 0xc600004c>,
+ <IMX8QM_SAI1_TXFS_AUD_SAI1_TXFS 0xc600004c>;
+ };
+
+ /* Apalis SATA1_ACT# */
+ pinctrl_sata1_act: sata1actgrp {
+ fsl,pins =
+ <IMX8QM_ESAI1_TX0_LSIO_GPIO2_IO08 0x00000021>;
+ };
+
+ /* Apalis SD1_CD# */
+ pinctrl_sd1_cd: sd1cdgrp {
+ fsl,pins =
+ <IMX8QM_USDHC2_CD_B_LSIO_GPIO4_IO12 0x00000021>;
+ };
+
+ /* On-module I2S SGTL5000 SYS_MCLK */
+ pinctrl_sgtl5000: sgtl5000grp {
+ fsl,pins =
+ <IMX8QM_MCLK_OUT0_AUD_ACM_MCLK_OUT0 0xc600004c>;
+ };
+
+ /* Apalis LCD1_ */
+ pinctrl_sim0_gpios: sim0gpiosgrp {
+ fsl,pins =
+ /* Apalis LCD1_G5 */
+ <IMX8QM_SIM0_CLK_LSIO_GPIO0_IO00 0x00000021>,
+ /* Apalis LCD1_G3 */
+ <IMX8QM_SIM0_GPIO0_00_LSIO_GPIO0_IO05 0x00000021>,
+ /* Apalis TS_5 */
+ <IMX8QM_SIM0_IO_LSIO_GPIO0_IO02 0x00000021>,
+ /* Apalis LCD1_G4 */
+ <IMX8QM_SIM0_RST_LSIO_GPIO0_IO01 0x00000021>;
+ };
+
+ /* Apalis SPDIF */
+ pinctrl_spdif0: spdif0grp {
+ fsl,pins =
+ <IMX8QM_SPDIF0_TX_AUD_SPDIF0_TX 0xc6000040>,
+ <IMX8QM_SPDIF0_RX_AUD_SPDIF0_RX 0xc6000040>;
+ };
+
+ pinctrl_touchctrl_gpios: touchctrlgpiosgrp {
+ fsl,pins =
+ <IMX8QM_ESAI1_FSR_LSIO_GPIO2_IO04 0x00000021>,
+ <IMX8QM_ESAI1_FST_LSIO_GPIO2_IO05 0x00000041>,
+ <IMX8QM_SPI3_SCK_LSIO_GPIO2_IO17 0x00000021>,
+ <IMX8QM_SPI3_CS1_LSIO_GPIO2_IO21 0x00000041>;
+ };
+
+ pinctrl_touchctrl_idle: touchctrlidlegrp {
+ fsl,pins =
+ <IMX8QM_ADC_IN4_LSIO_GPIO3_IO22 0x00000021>,
+ <IMX8QM_ADC_IN5_LSIO_GPIO3_IO23 0x00000021>,
+ <IMX8QM_ADC_IN6_LSIO_GPIO3_IO24 0x00000021>,
+ <IMX8QM_ADC_IN7_LSIO_GPIO3_IO25 0x00000021>;
+ };
+
+ /* On-module USB HSIC HUB (active) */
+ pinctrl_usb_hsic_active: usbh1activegrp {
+ fsl,pins =
+ <IMX8QM_USB_HSIC0_DATA_CONN_USB_HSIC0_DATA 0x000000cf>,
+ <IMX8QM_USB_HSIC0_STROBE_CONN_USB_HSIC0_STROBE 0x000000ff>;
+ };
+
+ /* On-module USB HSIC HUB (idle) */
+ pinctrl_usb_hsic_idle: usbh1idlegrp {
+ fsl,pins =
+ <IMX8QM_USB_HSIC0_DATA_CONN_USB_HSIC0_DATA 0x000000cf>,
+ <IMX8QM_USB_HSIC0_STROBE_CONN_USB_HSIC0_STROBE 0x000000cf>;
+ };
+
+ /* On-module USB HSIC HUB */
+ pinctrl_usb3503a: usb3503agrp {
+ fsl,pins =
+ /* On-module HSIC_HUB_CONNECT */
+ <IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31 0x00000041>,
+ /* On-module HSIC_INT_N */
+ <IMX8QM_SCU_GPIO0_05_LSIO_GPIO1_IO01 0x00000021>,
+ /* On-module HSIC_RESET_N */
+ <IMX8QM_SCU_GPIO0_06_LSIO_GPIO1_IO02 0x00000041>;
+ };
+
+ /* Apalis USBH_EN */
+ pinctrl_usbh_en: usbhengrp {
+ fsl,pins =
+ <IMX8QM_USB_SS3_TC1_LSIO_GPIO4_IO04 0x00000021>;
+ };
+
+ /* Apalis USBO1 */
+ pinctrl_usbotg1: usbotg1grp {
+ fsl,pins =
+ /* Apalis USBO1_EN */
+ <IMX8QM_USB_SS3_TC0_CONN_USB_OTG1_PWR 0x00000021>,
+ /* Apalis USBO1_OC# */
+ <IMX8QM_USB_SS3_TC2_CONN_USB_OTG1_OC 0x04000021>;
+ };
+
+ /* On-module eMMC */
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins =
+ <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041>,
+ <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021>,
+ <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021>,
+ <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021>,
+ <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021>,
+ <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021>,
+ <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021>,
+ <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021>,
+ <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021>,
+ <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021>,
+ <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE 0x06000041>,
+ <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000021>;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+ fsl,pins =
+ <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040>,
+ <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD 0x00000020>,
+ <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000020>,
+ <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000020>,
+ <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000020>,
+ <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000020>,
+ <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000020>,
+ <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000020>,
+ <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000020>,
+ <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000020>,
+ <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE 0x06000040>,
+ <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000020>;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+ fsl,pins =
+ <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040>,
+ <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD 0x00000020>,
+ <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000020>,
+ <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000020>,
+ <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000020>,
+ <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000020>,
+ <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000020>,
+ <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000020>,
+ <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000020>,
+ <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000020>,
+ <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE 0x06000040>,
+ <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000020>;
+ };
+
+ /* Apalis TS_6 */
+ pinctrl_usdhc1_gpios: usdhc1gpiosgrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_STROBE_LSIO_GPIO5_IO23 0x00000021>;
+ };
+
+ /* Apalis MMC1 */
+ pinctrl_usdhc2_4bit: usdhc2grp4bitgrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041>,
+ <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021>,
+ <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021>,
+ <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021>,
+ <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021>,
+ <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021>,
+ /* On-module PMIC use */
+ <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021>;
+ };
+
+ pinctrl_usdhc2_4bit_100mhz: usdhc2-4bit100mhzgrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK 0x06000040>,
+ <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD 0x00000020>,
+ <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000020>,
+ <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000020>,
+ <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000020>,
+ <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000020>,
+ /* On-module PMIC use */
+ <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021>;
+ };
+
+ pinctrl_usdhc2_4bit_200mhz: usdhc2-4bit200mhzgrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK 0x06000040>,
+ <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD 0x00000020>,
+ <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000020>,
+ <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000020>,
+ <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000020>,
+ <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000020>,
+ /* On-module PMIC use */
+ <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021>;
+ };
+
+ pinctrl_usdhc2_8bit: usdhc2grp8bitgrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4 0x00000021>,
+ <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5 0x00000021>,
+ <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6 0x00000021>,
+ <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7 0x00000021>;
+ };
+
+ pinctrl_usdhc2_8bit_100mhz: usdhc2-8bit100mhzgrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4 0x00000020>,
+ <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5 0x00000020>,
+ <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6 0x00000020>,
+ <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7 0x00000020>;
+ };
+
+ pinctrl_usdhc2_8bit_200mhz: usdhc2-8bit200mhzgrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4 0x00000020>,
+ <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5 0x00000020>,
+ <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6 0x00000020>,
+ <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7 0x00000020>;
+ };
+
+ pinctrl_usdhc2_4bit_sleep: usdhc2-4bitsleepgrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK 0x04000061>,
+ <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD 0x04000061>,
+ <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0 0x04000061>,
+ <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1 0x04000061>,
+ <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2 0x04000061>,
+ <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3 0x04000061>,
+ /* On-module PMIC use */
+ <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021>;
+ };
+
+ pinctrl_usdhc2_8bit_sleep: usdhc2-8bitsleepgrp {
+ fsl,pins =
+ <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4 0x04000061>,
+ <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5 0x04000061>,
+ <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6 0x04000061>,
+ <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7 0x04000061>;
+ };
+
+ /* Apalis SD1 */
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins =
+ <IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK 0x06000041>,
+ <IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD 0x00000021>,
+ <IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000021>,
+ <IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000021>,
+ <IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000021>,
+ <IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000021>,
+ /* On-module PMIC use */
+ <IMX8QM_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000021>;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+ fsl,pins =
+ <IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK 0x06000041>,
+ <IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD 0x00000021>,
+ <IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000021>,
+ <IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000021>,
+ <IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000021>,
+ <IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000021>,
+ /* On-module PMIC use */
+ <IMX8QM_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000021>;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+ fsl,pins =
+ <IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK 0x06000041>,
+ <IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD 0x00000021>,
+ <IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000021>,
+ <IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000021>,
+ <IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000021>,
+ <IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000021>,
+ /* On-module PMIC use */
+ <IMX8QM_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000021>;
+ };
+
+ /* On-module Wi-Fi */
+ pinctrl_wifi: wifigrp {
+ fsl,pins =
+ /* On-module Wi-Fi_SUSCLK_32k */
+ <IMX8QM_SCU_GPIO0_07_SCU_DSC_RTC_CLOCK_OUTPUT_32K 0x06000021>,
+ /* On-module Wi-Fi_PCIE_W_DISABLE */
+ <IMX8QM_MIPI_CSI0_MCLK_OUT_LSIO_GPIO1_IO24 0x06000021>;
+ };
+
+ pinctrl_wifi_pdn: wifipdngrp {
+ fsl,pins =
+ /* On-module Wi-Fi_POWER_DOWN */
+ <IMX8QM_MIPI_CSI0_GPIO0_01_LSIO_GPIO1_IO28 0x06000021>;
+ };
+};
new file mode 100644
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8qm-apalis.dtsi"
+#include "imx8-apalis-eval.dtsi"
+
+/ {
+ model = "Toradex Apalis iMX8QM/QP on Apalis Evaluation Board";
+ compatible = "toradex,apalis-imx8-eval",
+ "toradex,apalis-imx8",
+ "fsl,imx8qm";
+};
new file mode 100644
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8qm-apalis.dtsi"
+#include "imx8-apalis-ixora-v1.1.dtsi"
+
+/ {
+ model = "Toradex Apalis iMX8QM/QP on Apalis Ixora V1.1 Carrier Board";
+ compatible = "toradex,apalis-imx8-ixora-v1.1",
+ "toradex,apalis-imx8",
+ "fsl,imx8qm";
+};
new file mode 100644
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8qm-apalis-v1.1.dtsi"
+#include "imx8-apalis-eval.dtsi"
+
+/ {
+ model = "Toradex Apalis iMX8QM V1.1 on Apalis Evaluation Board";
+ compatible = "toradex,apalis-imx8-v1.1-eval",
+ "toradex,apalis-imx8-v1.1",
+ "fsl,imx8qm";
+};
new file mode 100644
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8qm-apalis-v1.1.dtsi"
+#include "imx8-apalis-ixora-v1.1.dtsi"
+
+/ {
+ model = "Toradex Apalis iMX8QM V1.1 on Apalis Ixora V1.1 Carrier Board";
+ compatible = "toradex,apalis-imx8-v1.1-ixora-v1.1",
+ "toradex,apalis-imx8-v1.1",
+ "fsl,imx8qm";
+};
new file mode 100644
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8qm-apalis-v1.1.dtsi"
+#include "imx8-apalis-ixora-v1.2.dtsi"
+
+/ {
+ model = "Toradex Apalis iMX8QM V1.1 on Apalis Ixora V1.2 Carrier Board";
+ compatible = "toradex,apalis-imx8-v1.1-ixora-v1.2",
+ "toradex,apalis-imx8-v1.1",
+ "fsl,imx8qm";
+};
new file mode 100644
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include <dt-bindings/pwm/pwm.h>
+#include "imx8qm.dtsi"
+#include "imx8-apalis-v1.1.dtsi"
+
+/ {
+ model = "Toradex Apalis iMX8QM V1.1";
+ compatible = "toradex,apalis-imx8-v1.1",
+ "toradex,apalis-imx8",
+ "fsl,imx8qm";
+};
+
+/* TODO: Cooling Maps */
new file mode 100644
@@ -0,0 +1,342 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "imx8qm-apalis-v1.1.dtsi"
+
+/ {
+ model = "Toradex Apalis iMX8QM";
+ compatible = "toradex,apalis-imx8",
+ "fsl,imx8qm";
+};
+
+/* TODO: Delete PCIe Wi-Fi Reference Clock */
+
+ðphy0 {
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+};
+
+/*
+ * Apalis iMX8QM V1.0 has PHY KSZ9031. the Micrel PHY driver
+ * doesn't support setting internal PHY delay for TXC line for
+ * this PHY model. Use delay on MAC side instead.
+ */
+&fec1 {
+ fsl,rgmii_txc_dly;
+ phy-mode = "rgmii-rxid";
+};
+
+/* TODO: Apalis HDMI1 */
+
+/* Apalis I2C2 (DDC) */
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+};
+
+&lsio_gpio0 {
+ gpio-line-names = "MXM3_279",
+ "MXM3_277",
+ "MXM3_135",
+ "MXM3_203",
+ "MXM3_201",
+ "MXM3_275",
+ "MXM3_110",
+ "MXM3_120",
+ "MXM3_1/GPIO1",
+ "MXM3_3/GPIO2",
+ "MXM3_124",
+ "MXM3_122",
+ "MXM3_5/GPIO3",
+ "MXM3_7/GPIO4",
+ "",
+ "",
+ "MXM3_4",
+ "MXM3_211",
+ "MXM3_209",
+ "MXM3_2",
+ "MXM3_136",
+ "MXM3_134",
+ "MXM3_6",
+ "MXM3_8",
+ "MXM3_112",
+ "MXM3_118",
+ "MXM3_114",
+ "MXM3_116";
+};
+
+&lsio_gpio1 {
+ gpio-line-names = "",
+ "",
+ "",
+ "",
+ "MXM3_286",
+ "",
+ "MXM3_87",
+ "MXM3_99",
+ "MXM3_138",
+ "MXM3_140",
+ "MXM3_239",
+ "",
+ "MXM3_281",
+ "MXM3_283",
+ "MXM3_126",
+ "MXM3_132",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_173",
+ "MXM3_175",
+ "MXM3_123";
+};
+
+&lsio_gpio2 {
+ gpio-line-names = "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_198",
+ "MXM3_35",
+ "MXM3_164",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_217",
+ "MXM3_215",
+ "",
+ "",
+ "MXM3_193",
+ "MXM3_194",
+ "MXM3_37",
+ "",
+ "MXM3_271",
+ "MXM3_273",
+ "MXM3_195",
+ "MXM3_197",
+ "MXM3_177",
+ "MXM3_179",
+ "MXM3_181",
+ "MXM3_183",
+ "MXM3_185",
+ "MXM3_187";
+};
+
+&lsio_gpio3 {
+ gpio-line-names = "MXM3_191",
+ "",
+ "MXM3_221",
+ "MXM3_225",
+ "MXM3_223",
+ "MXM3_227",
+ "MXM3_200",
+ "MXM3_235",
+ "MXM3_231",
+ "MXM3_229",
+ "MXM3_233",
+ "MXM3_204",
+ "MXM3_196",
+ "",
+ "MXM3_202",
+ "",
+ "",
+ "",
+ "MXM3_305",
+ "MXM3_307",
+ "MXM3_309",
+ "MXM3_311",
+ "MXM3_315",
+ "MXM3_317",
+ "MXM3_319",
+ "MXM3_321",
+ "MXM3_15/GPIO7",
+ "MXM3_63",
+ "MXM3_17/GPIO8",
+ "MXM3_12",
+ "MXM3_14",
+ "MXM3_16";
+};
+
+&lsio_gpio4 {
+ gpio-line-names = "MXM3_18",
+ "MXM3_11/GPIO5",
+ "MXM3_13/GPIO6",
+ "MXM3_274",
+ "MXM3_84",
+ "MXM3_262",
+ "MXM3_96",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_190",
+ "",
+ "",
+ "",
+ "MXM3_269",
+ "MXM3_251",
+ "MXM3_253",
+ "MXM3_295",
+ "MXM3_299",
+ "MXM3_301",
+ "MXM3_297",
+ "MXM3_293",
+ "MXM3_291",
+ "MXM3_289",
+ "MXM3_287";
+
+ /* Enable pcie root / sata ref clock unconditionally */
+ pcie_sata_hog {
+ gpios = <27 GPIO_ACTIVE_HIGH>;
+ };
+
+};
+
+&lsio_gpio5 {
+ gpio-line-names = "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_150",
+ "MXM3_160",
+ "MXM3_162",
+ "MXM3_144",
+ "MXM3_146",
+ "MXM3_148",
+ "MXM3_152",
+ "MXM3_156",
+ "MXM3_158",
+ "MXM3_159",
+ "MXM3_184",
+ "MXM3_180",
+ "MXM3_186",
+ "MXM3_188",
+ "MXM3_176",
+ "MXM3_178";
+};
+
+&lsio_gpio6 {
+ gpio-line-names = "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "MXM3_261",
+ "MXM3_263",
+ "MXM3_259",
+ "MXM3_257",
+ "MXM3_255",
+ "MXM3_128",
+ "MXM3_130",
+ "MXM3_265",
+ "MXM3_249",
+ "MXM3_247",
+ "MXM3_245",
+ "MXM3_243";
+};
+
+&pinctrl_fec1 {
+ fsl,pins =
+ /* Use pads in 1.8V mode */
+ <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD 0x000014a0>,
+ <IMX8QM_ENET0_MDC_CONN_ENET0_MDC 0x06000020>,
+ <IMX8QM_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x06000020>,
+ <IMX8QM_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x06000020>,
+ <IMX8QM_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x06000020>,
+ <IMX8QM_ENET0_REFCLK_125M_25M_CONN_ENET0_REFCLK_125M_25M 0x06000020>,
+ /* On-module ETH_RESET# */
+ <IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11 0x06000020>,
+ /* On-module ETH_INT# */
+ <IMX8QM_LVDS0_GPIO01_LSIO_GPIO1_IO05 0x04000060>;
+};
+
+&pinctrl_fec1_sleep {
+ fsl,pins =
+ <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD 0x000014a0>,
+ <IMX8QM_ENET0_MDC_LSIO_GPIO4_IO14 0x04000040>,
+ <IMX8QM_ENET0_MDIO_LSIO_GPIO4_IO13 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TX_CTL_LSIO_GPIO5_IO31 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TXC_LSIO_GPIO5_IO30 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TXD0_LSIO_GPIO6_IO00 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TXD1_LSIO_GPIO6_IO01 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TXD2_LSIO_GPIO6_IO02 0x04000040>,
+ <IMX8QM_ENET0_RGMII_TXD3_LSIO_GPIO6_IO03 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RXC_LSIO_GPIO6_IO04 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RX_CTL_LSIO_GPIO6_IO05 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RXD0_LSIO_GPIO6_IO06 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RXD1_LSIO_GPIO6_IO07 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RXD2_LSIO_GPIO6_IO08 0x04000040>,
+ <IMX8QM_ENET0_RGMII_RXD3_LSIO_GPIO6_IO09 0x04000040>,
+ <IMX8QM_ENET0_REFCLK_125M_25M_LSIO_GPIO4_IO15 0x04000040>,
+ <IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11 0x04000040>,
+ <IMX8QM_LVDS0_GPIO01_LSIO_GPIO1_IO05 0x04000040>;
+};
+
+&iomuxc {
+ /* Apalis I2C2 (DDC) */
+ pinctrl_lpi2c0: lpi2c0grp {
+ fsl,pins =
+ <IMX8QM_HDMI_TX0_TS_SCL_DMA_I2C0_SCL 0x04000022>,
+ <IMX8QM_HDMI_TX0_TS_SDA_DMA_I2C0_SDA 0x04000022>;
+ };
+};
+
+/* On-module PCIe_CTRL0_CLKREQ */
+&pinctrl_pcie_sata_refclk {
+ fsl,pins =
+ <IMX8QM_PCIE_CTRL0_CLKREQ_B_LSIO_GPIO4_IO27 0x00000021>;
+};
+
+/* TODO: On-module Wi-Fi */
+
+/* Apalis MMC1 */
+&usdhc2 {
+ /*
+ * The PMIC on V1.0A HW generates 1.6V instead of 1.8V which creates
+ * issues with certain SD cards, disable 1.8V signaling for now.
+ */
+ no-1-8-v;
+};
+
+/* Apalis SD1 */
+&usdhc3 {
+ /*
+ * The PMIC on V1.0A HW generates 1.6V instead of 1.8V which creates
+ * issues with certain SD cards, disable 1.8V signaling for now.
+ */
+ no-1-8-v;
+};