diff mbox series

[v11,7/8] arm64: dts: ti: k3-j721s2-main: Add PCIe device tree node

Message ID 20230224102438.6541-8-r-gunasekaran@ti.com (mailing list archive)
State New, archived
Headers show
Series arm64: j721s2: Add support for additional IPs | expand

Commit Message

Ravi Gunasekaran Feb. 24, 2023, 10:24 a.m. UTC 
From: Aswath Govindraju <a-govindraju@ti.com>

Add PCIe1 RC device tree node for the single PCIe instance present on
the j721s2.

Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
---
Changes from v10:
* Removed Link tag from commit message

Changes from v9:
* No change

Changes from v8:
* No change

Changes from v7:
* No change

Changes from v6:
* Remove the pcie_ep node as device cannot act as RC and EP
  at the same time

Changes from v5:
* No change

Changes from v4:
* No change

Changes from v3:
* No change

Changes from v2:
* Patch newly added to the series

 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 47 ++++++++++++++++++++++
 1 file changed, 47 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index c9b90ffb4f7c..35aae4b52c54 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -871,6 +871,53 @@ 
 		};
 	};
 
+	pcie1_rc: pcie@2910000 {
+		compatible = "ti,j7200-pcie-host", "ti,j721e-pcie-host";
+		reg = <0x00 0x02910000 0x00 0x1000>,
+		      <0x00 0x02917000 0x00 0x400>,
+		      <0x00 0x0d800000 0x00 0x00800000>,
+		      <0x00 0x18000000 0x00 0x00001000>;
+		reg-names = "intd_cfg", "user_cfg", "reg", "cfg";
+		interrupt-names = "link_state";
+		interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+		device_type = "pci";
+		ti,syscon-pcie-ctrl = <&scm_conf 0x074>;
+		max-link-speed = <3>;
+		num-lanes = <4>;
+		power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 276 41>;
+		clock-names = "fck";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		bus-range = <0x0 0xff>;
+		vendor-id = <0x104c>;
+		device-id = <0xb013>;
+		msi-map = <0x0 &gic_its 0x0 0x10000>;
+		dma-coherent;
+		ranges = <0x01000000 0x0 0x18001000  0x00 0x18001000  0x0 0x0010000>,
+			 <0x02000000 0x0 0x18011000  0x00 0x18011000  0x0 0x7fef000>;
+		dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie1_intc 0>, /* INT A */
+				<0 0 0 2 &pcie1_intc 0>, /* INT B */
+				<0 0 0 3 &pcie1_intc 0>, /* INT C */
+				<0 0 0 4 &pcie1_intc 0>; /* INT D */
+		/*
+		 * Disable the node by default in the common include file.
+		 * And enable it in the board specific DT file where the
+		 * pinmux property is added.
+		 */
+		status = "disabled";
+
+		pcie1_intc: interrupt-controller {
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 324 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,