@@ -179,6 +179,9 @@ static inline void serial_dl_write(struct uart_8250_port *up, u32 value)
static inline bool serial8250_set_THRI(struct uart_8250_port *up)
{
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&up->port.lock);
+
if (up->ier & UART_IER_THRI)
return false;
up->ier |= UART_IER_THRI;
@@ -188,6 +191,9 @@ static inline bool serial8250_set_THRI(struct uart_8250_port *up)
static inline bool serial8250_clear_THRI(struct uart_8250_port *up)
{
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&up->port.lock);
+
if (!(up->ier & UART_IER_THRI))
return false;
up->ier &= ~UART_IER_THRI;
@@ -275,6 +275,9 @@ static void __aspeed_vuart_set_throttle(struct uart_8250_port *up,
{
unsigned char irqs = UART_IER_RLSI | UART_IER_RDI;
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&up->port.lock);
+
up->ier &= ~irqs;
if (!throttle)
up->ier |= irqs;
@@ -222,11 +222,17 @@ static void mtk8250_shutdown(struct uart_port *port)
static void mtk8250_disable_intrs(struct uart_8250_port *up, int mask)
{
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&up->port.lock);
+
serial_out(up, UART_IER, serial_in(up, UART_IER) & (~mask));
}
static void mtk8250_enable_intrs(struct uart_8250_port *up, int mask)
{
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&up->port.lock);
+
serial_out(up, UART_IER, serial_in(up, UART_IER) | mask);
}
@@ -235,6 +241,9 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
struct uart_port *port = &up->port;
int lcr = serial_in(up, UART_LCR);
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&port->lock);
+
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
serial_out(up, UART_LCR, lcr);
@@ -533,6 +533,10 @@ static void omap_8250_pm(struct uart_port *port, unsigned int state,
u8 efr;
pm_runtime_get_sync(port->dev);
+
+ /* Synchronize UART_IER access against the console. */
+ spin_lock_irq(&port->lock);
+
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, efr | UART_EFR_ECB);
@@ -543,6 +547,8 @@ static void omap_8250_pm(struct uart_port *port, unsigned int state,
serial_out(up, UART_EFR, efr);
serial_out(up, UART_LCR, 0);
+ spin_unlock_irq(&port->lock);
+
pm_runtime_mark_last_busy(port->dev);
pm_runtime_put_autosuspend(port->dev);
}
@@ -760,8 +766,11 @@ static void omap_8250_shutdown(struct uart_port *port)
if (priv->habit & UART_HAS_EFR2)
serial_out(up, UART_OMAP_EFR2, 0x0);
+ /* Synchronize UART_IER access against the console. */
+ spin_lock_irq(&port->lock);
up->ier = 0;
serial_out(up, UART_IER, 0);
+ spin_unlock_irq(&port->lock);
disable_irq_nosync(up->port.irq);
dev_pm_clear_wake_irq(port->dev);
@@ -803,6 +812,7 @@ static void omap_8250_unthrottle(struct uart_port *port)
pm_runtime_get_sync(port->dev);
+ /* Synchronize UART_IER access against the console. */
spin_lock_irqsave(&port->lock, flags);
priv->throttled = false;
if (up->dma)
@@ -953,6 +963,7 @@ static void __dma_rx_complete(void *param)
struct dma_tx_state state;
unsigned long flags;
+ /* Synchronize UART_IER access against the console. */
spin_lock_irqsave(&p->port.lock, flags);
/*
@@ -1227,6 +1238,9 @@ static u16 omap_8250_handle_rx_dma(struct uart_8250_port *up, u8 iir, u16 status
static void am654_8250_handle_rx_dma(struct uart_8250_port *up, u8 iir,
u16 status)
{
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&up->port.lock);
+
/*
* Queue a new transfer if FIFO has data.
*/
@@ -539,6 +539,9 @@ EXPORT_SYMBOL_GPL(serial8250_rpm_put);
*/
static int serial8250_em485_init(struct uart_8250_port *p)
{
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&p->port.lock);
+
if (p->em485)
goto deassert_rts;
@@ -676,6 +679,8 @@ static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
serial8250_rpm_get(p);
if (p->capabilities & UART_CAP_SLEEP) {
+ /* Synchronize UART_IER access against the console. */
+ spin_lock_irq(&p->port.lock);
if (p->capabilities & UART_CAP_EFR) {
lcr = serial_in(p, UART_LCR);
efr = serial_in(p, UART_EFR);
@@ -689,6 +694,7 @@ static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
serial_out(p, UART_EFR, efr);
serial_out(p, UART_LCR, lcr);
}
+ spin_unlock_irq(&p->port.lock);
}
serial8250_rpm_put(p);
@@ -696,6 +702,9 @@ static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
static void serial8250_clear_IER(struct uart_8250_port *up)
{
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&up->port.lock);
+
if (up->capabilities & UART_CAP_UUE)
serial_out(up, UART_IER, UART_IER_UUE);
else
@@ -968,6 +977,9 @@ static void autoconfig_16550a(struct uart_8250_port *up)
unsigned char status1, status2;
unsigned int iersave;
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&up->port.lock);
+
up->port.type = PORT_16550A;
up->capabilities |= UART_CAP_FIFO;
@@ -1151,6 +1163,8 @@ static void autoconfig(struct uart_8250_port *up)
/*
* We really do need global IRQs disabled here - we're going to
* be frobbing the chips IRQ enable register to see if it exists.
+ *
+ * Synchronize UART_IER access against the console.
*/
spin_lock_irqsave(&port->lock, flags);
@@ -1323,7 +1337,10 @@ static void autoconfig_irq(struct uart_8250_port *up)
/* forget possible initially masked and pending IRQ */
probe_irq_off(probe_irq_on());
save_mcr = serial8250_in_MCR(up);
+ /* Synchronize UART_IER access against the console. */
+ spin_lock_irq(&port->lock);
save_ier = serial_in(up, UART_IER);
+ spin_unlock_irq(&port->lock);
serial8250_out_MCR(up, UART_MCR_OUT1 | UART_MCR_OUT2);
irqs = probe_irq_on();
@@ -1335,7 +1352,10 @@ static void autoconfig_irq(struct uart_8250_port *up)
serial8250_out_MCR(up,
UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
}
+ /* Synchronize UART_IER access against the console. */
+ spin_lock_irq(&port->lock);
serial_out(up, UART_IER, UART_IER_ALL_INTR);
+ spin_unlock_irq(&port->lock);
serial_in(up, UART_LSR);
serial_in(up, UART_RX);
serial_in(up, UART_IIR);
@@ -1345,7 +1365,10 @@ static void autoconfig_irq(struct uart_8250_port *up)
irq = probe_irq_off(irqs);
serial8250_out_MCR(up, save_mcr);
+ /* Synchronize UART_IER access against the console. */
+ spin_lock_irq(&port->lock);
serial_out(up, UART_IER, save_ier);
+ spin_unlock_irq(&port->lock);
if (port->flags & UPF_FOURPORT)
outb_p(save_ICP, ICP);
@@ -1360,6 +1383,9 @@ static void serial8250_stop_rx(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&port->lock);
+
serial8250_rpm_get(up);
up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
@@ -1379,6 +1405,9 @@ void serial8250_em485_stop_tx(struct uart_8250_port *p)
{
unsigned char mcr = serial8250_in_MCR(p);
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&p->port.lock);
+
if (p->port.rs485.flags & SER_RS485_RTS_AFTER_SEND)
mcr |= UART_MCR_RTS;
else
@@ -1428,6 +1457,9 @@ static void __stop_tx_rs485(struct uart_8250_port *p, u64 stop_delay)
{
struct uart_8250_em485 *em485 = p->em485;
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&p->port.lock);
+
stop_delay += (u64)p->port.rs485.delay_rts_after_send * NSEC_PER_MSEC;
/*
@@ -1607,6 +1639,9 @@ static void serial8250_start_tx(struct uart_port *port)
struct uart_8250_port *up = up_to_u8250p(port);
struct uart_8250_em485 *em485 = up->em485;
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&port->lock);
+
if (!port->x_char && uart_circ_empty(&port->state->xmit))
return;
@@ -1634,6 +1669,9 @@ static void serial8250_disable_ms(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&port->lock);
+
/* no MSR capabilities */
if (up->bugs & UART_BUG_NOMSR)
return;
@@ -1648,6 +1686,9 @@ static void serial8250_enable_ms(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
+ /* Port locked to synchronize UART_IER access against the console. */
+ lockdep_assert_held_once(&port->lock);
+
/* no MSR capabilities */
if (up->bugs & UART_BUG_NOMSR)
return;
@@ -2104,6 +2145,14 @@ static void serial8250_put_poll_char(struct uart_port *port,
unsigned int ier;
struct uart_8250_port *up = up_to_u8250p(port);
+ /*
+ * Normally the port is locked to synchronize UART_IER access
+ * against the console. However, this function is only used by
+ * KDB/KGDB, where it may not be possible to acquire the port
+ * lock because all other CPUs are quiesced. The quiescence
+ * should allow safe lockless usage here.
+ */
+
serial8250_rpm_get(up);
/*
* First save the IER then disable the interrupts
@@ -2439,6 +2488,8 @@ void serial8250_do_shutdown(struct uart_port *port)
serial8250_rpm_get(up);
/*
* Disable interrupts from this port
+ *
+ * Synchronize UART_IER access against the console.
*/
spin_lock_irqsave(&port->lock, flags);
up->ier = 0;
@@ -2738,6 +2789,8 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
+ *
+ * Synchronize UART_IER access against the console.
*/
serial8250_rpm_get(up);
spin_lock_irqsave(&port->lock, flags);
The UART_IER register is modified twice by each console write (serial8250_console_write()) under the port lock. Any driver code that accesses UART_IER must do so with the port locked in order to ensure consistent values, even when for read accesses. Add locking, lockdep notation, and/or comments everywhere UART_IER is accessed. The added locking is not fixing a real problem because it occurs where the console is not active. However, adding the locking to these non-critical paths greatly simplifies UART_IER access tracking by establishing a general policy that all UART_IER access is performed with the port locked. Signed-off-by: John Ogness <john.ogness@linutronix.de> --- drivers/tty/serial/8250/8250.h | 6 +++ drivers/tty/serial/8250/8250_aspeed_vuart.c | 3 ++ drivers/tty/serial/8250/8250_mtk.c | 9 ++++ drivers/tty/serial/8250/8250_omap.c | 14 ++++++ drivers/tty/serial/8250/8250_port.c | 53 +++++++++++++++++++++ 5 files changed, 85 insertions(+)