@@ -51,6 +51,16 @@ config PWM_AB8500
To compile this driver as a module, choose M here: the module
will be called pwm-ab8500.
+config PWM_ASPEED_AST2600
+ tristate "Aspeed ast2600 PWM support"
+ depends on ARCH_ASPEED || COMPILE_TEST
+ depends on HAVE_CLK && HAS_IOMEM
+ help
+ This driver provides support for Aspeed ast2600 PWM controllers.
+
+ To compile this driver as a module, choose M here: the module
+ will be called pwm-aspeed-ast2600.
+
config PWM_ATMEL
tristate "Atmel PWM support"
depends on ARCH_AT91 || COMPILE_TEST
@@ -2,6 +2,7 @@
obj-$(CONFIG_PWM) += core.o
obj-$(CONFIG_PWM_SYSFS) += sysfs.o
obj-$(CONFIG_PWM_AB8500) += pwm-ab8500.o
+obj-$(CONFIG_PWM_ASPEED_AST2600) += pwm-aspeed-ast2600.o
obj-$(CONFIG_PWM_ATMEL) += pwm-atmel.o
obj-$(CONFIG_PWM_ATMEL_HLCDC_PWM) += pwm-atmel-hlcdc.o
obj-$(CONFIG_PWM_ATMEL_TCB) += pwm-atmel-tcb.o
new file mode 100644
@@ -0,0 +1,309 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2021 Aspeed Technology Inc.
+ *
+ * PWM controller driver for Aspeed ast2600 SoCs.
+ * This drivers doesn't support earlier version of the IP.
+ *
+ * The hardware operates in time quantities of length
+ * Q := (DIV_L + 1) << DIV_H / input-clk
+ * The length of a PWM period is (DUTY_CYCLE_PERIOD + 1) * Q.
+ * The maximal value for DUTY_CYCLE_PERIOD is used here to provide
+ * a fine grained selection for the duty cycle.
+ *
+ * This driver uses DUTY_CYCLE_RISING_POINT = 0, so from the start of a
+ * period the output is active until DUTY_CYCLE_FALLING_POINT * Q. Note
+ * that if DUTY_CYCLE_RISING_POINT = DUTY_CYCLE_FALLING_POINT the output is
+ * always active.
+ *
+ * Register usage:
+ * PIN_ENABLE: When it is unset the pwm controller will emit inactive level to the external.
+ * Use to determine whether the PWM channel is enabled or disabled
+ * CLK_ENABLE: When it is unset the pwm controller will assert the duty counter reset and
+ * emit inactive level to the PIN_ENABLE mux after that the driver can still change the pwm period
+ * and duty and the value will apply when CLK_ENABLE be set again.
+ * Use to determine whether duty_cycle bigger than 0.
+ * PWM_ASPEED_CTRL_INVERSE: When it is toggled the output value will inverse immediately.
+ * PWM_ASPEED_DUTY_CYCLE_FALLING_POINT/PWM_ASPEED_DUTY_CYCLE_RISING_POINT: When these two
+ * values are equal it means the duty cycle = 100%.
+ *
+ * The glitch may generate at:
+ * - Enabled changing when the duty_cycle bigger than 0% and less than 100%.
+ * - Polarity changing when the duty_cycle bigger than 0% and less than 100%.
+ *
+ * Limitations:
+ * - When changing both duty cycle and period, we cannot prevent in
+ * software that the output might produce a period with mixed
+ * settings.
+ * - Disabling the PWM doesn't complete the current period.
+ *
+ * Improvements:
+ * - When only changing one of duty cycle or period, our pwm controller will not
+ * generate the glitch, the configure will change at next cycle of pwm.
+ * This improvement can disable/enable through PWM_ASPEED_CTRL_DUTY_SYNC_DISABLE.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+#include <linux/reset.h>
+#include <linux/sysfs.h>
+
+/* PWM Control Register */
+#define PWM_ASPEED_CTRL (0x00)
+#define PWM_ASPEED_CTRL_LOAD_SEL_RISING_AS_WDT BIT(19)
+#define PWM_ASPEED_CTRL_DUTY_LOAD_AS_WDT_ENABLE BIT(18)
+#define PWM_ASPEED_CTRL_DUTY_SYNC_DISABLE BIT(17)
+#define PWM_ASPEED_CTRL_CLK_ENABLE BIT(16)
+#define PWM_ASPEED_CTRL_LEVEL_OUTPUT BIT(15)
+#define PWM_ASPEED_CTRL_INVERSE BIT(14)
+#define PWM_ASPEED_CTRL_OPEN_DRAIN_ENABLE BIT(13)
+#define PWM_ASPEED_CTRL_PIN_ENABLE BIT(12)
+#define PWM_ASPEED_CTRL_CLK_DIV_H GENMASK(11, 8)
+#define PWM_ASPEED_CTRL_CLK_DIV_L GENMASK(7, 0)
+
+/* PWM Duty Cycle Register */
+#define PWM_ASPEED_DUTY_CYCLE (0x04)
+#define PWM_ASPEED_DUTY_CYCLE_PERIOD GENMASK(31, 24)
+#define PWM_ASPEED_DUTY_CYCLE_POINT_AS_WDT GENMASK(23, 16)
+#define PWM_ASPEED_DUTY_CYCLE_FALLING_POINT GENMASK(15, 8)
+#define PWM_ASPEED_DUTY_CYCLE_RISING_POINT GENMASK(7, 0)
+
+/* PWM fixed value */
+#define PWM_ASPEED_FIXED_PERIOD FIELD_MAX(PWM_ASPEED_DUTY_CYCLE_PERIOD)
+
+struct aspeed_pwm_data {
+ struct pwm_chip chip;
+ struct clk *clk;
+ void __iomem *base;
+ struct reset_control *reset;
+ unsigned long clk_source;
+};
+
+static inline struct aspeed_pwm_data *
+aspeed_pwm_chip_to_data(struct pwm_chip *chip)
+{
+ return container_of(chip, struct aspeed_pwm_data, chip);
+}
+
+static int aspeed_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
+ struct pwm_state *state)
+{
+ struct device *dev = chip->dev;
+ struct aspeed_pwm_data *priv = aspeed_pwm_chip_to_data(chip);
+ bool polarity, pin_en, clk_en;
+ u32 duty_pt, val;
+ u64 div_h, div_l, duty_cycle_period, dividend;
+
+ val = readl(priv->base + PWM_ASPEED_CTRL);
+ polarity = FIELD_GET(PWM_ASPEED_CTRL_INVERSE, val);
+ pin_en = FIELD_GET(PWM_ASPEED_CTRL_PIN_ENABLE, val);
+ clk_en = FIELD_GET(PWM_ASPEED_CTRL_CLK_ENABLE, val);
+ div_h = FIELD_GET(PWM_ASPEED_CTRL_CLK_DIV_H, val);
+ div_l = FIELD_GET(PWM_ASPEED_CTRL_CLK_DIV_L, val);
+ val = readl(priv->base + PWM_ASPEED_DUTY_CYCLE);
+ duty_pt = FIELD_GET(PWM_ASPEED_DUTY_CYCLE_FALLING_POINT, val);
+ duty_cycle_period = FIELD_GET(PWM_ASPEED_DUTY_CYCLE_PERIOD, val);
+
+ /*
+ * This multiplication doesn't overflow, the upper bound is
+ * 1000000000 * 256 * 256 << 15 = 0x1dcd650000000000
+ */
+ dividend = (u64)NSEC_PER_SEC * (div_l + 1) * (duty_cycle_period + 1)
+ << div_h;
+ state->period = DIV_ROUND_UP_ULL(dividend, priv->clk_source);
+
+ if (clk_en && duty_pt) {
+ dividend = (u64)NSEC_PER_SEC * (div_l + 1) * duty_pt
+ << div_h;
+ state->duty_cycle =
+ DIV_ROUND_UP_ULL(dividend, priv->clk_source);
+ } else {
+ state->duty_cycle = clk_en ? state->period : 0;
+ }
+ state->polarity = polarity ? PWM_POLARITY_INVERSED : PWM_POLARITY_NORMAL;
+ state->enabled = pin_en;
+ dev_dbg(dev, "get period: %lldns, duty_cycle: %lldns", state->period,
+ state->duty_cycle);
+ return 0;
+}
+
+static int aspeed_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ struct device *dev = chip->dev;
+ struct aspeed_pwm_data *priv = aspeed_pwm_chip_to_data(chip);
+ u32 duty_pt;
+ u64 div_h, div_l, divisor, expect_period;
+ bool clk_en;
+
+ expect_period = min(div64_u64(ULLONG_MAX, (u64)priv->clk_source),
+ state->period);
+ dev_dbg(dev, "expect period: %lldns, duty_cycle: %lldns", expect_period,
+ state->duty_cycle);
+ /*
+ * Pick the smallest value for div_h so that div_l can be the biggest
+ * which results in a finer resolution near the target period value.
+ */
+ divisor = (u64)NSEC_PER_SEC * (PWM_ASPEED_FIXED_PERIOD + 1) *
+ (FIELD_MAX(PWM_ASPEED_CTRL_CLK_DIV_L) + 1);
+ div_h = order_base_2(DIV64_U64_ROUND_UP(priv->clk_source * expect_period, divisor));
+ if (div_h > 0xf)
+ div_h = 0xf;
+
+ divisor = ((u64)NSEC_PER_SEC * (PWM_ASPEED_FIXED_PERIOD + 1)) << div_h;
+ div_l = div64_u64(priv->clk_source * expect_period, divisor);
+
+ if (div_l == 0)
+ return -ERANGE;
+
+ div_l -= 1;
+
+ if (div_l > 255)
+ div_l = 255;
+
+ dev_dbg(dev, "clk source: %ld div_h %lld, div_l : %lld\n",
+ priv->clk_source, div_h, div_l);
+ /* duty_pt = duty_cycle * (PERIOD + 1) / period */
+ duty_pt = div64_u64(state->duty_cycle * priv->clk_source,
+ (u64)NSEC_PER_SEC * (div_l + 1) << div_h);
+ dev_dbg(dev, "duty_cycle = %lld, duty_pt = %d\n", state->duty_cycle,
+ duty_pt);
+
+ /*
+ * Fixed DUTY_CYCLE_PERIOD to its max value to get a
+ * fine-grained resolution for duty_cycle at the expense of a
+ * coarser period resolution.
+ */
+ writel((readl(priv->base + PWM_ASPEED_DUTY_CYCLE) &
+ ~(PWM_ASPEED_DUTY_CYCLE_PERIOD)) |
+ FIELD_PREP(PWM_ASPEED_DUTY_CYCLE_PERIOD,
+ PWM_ASPEED_FIXED_PERIOD),
+ priv->base + PWM_ASPEED_DUTY_CYCLE);
+
+ if (duty_pt == 0) {
+ /* emit inactive level and assert the duty counter reset */
+ clk_en = 0;
+ } else {
+ clk_en = 1;
+ if (duty_pt >= (PWM_ASPEED_FIXED_PERIOD + 1))
+ duty_pt = 0;
+ writel((readl(priv->base + PWM_ASPEED_DUTY_CYCLE) &
+ ~(PWM_ASPEED_DUTY_CYCLE_RISING_POINT |
+ PWM_ASPEED_DUTY_CYCLE_FALLING_POINT)) |
+ FIELD_PREP(PWM_ASPEED_DUTY_CYCLE_FALLING_POINT,
+ duty_pt),
+ priv->base + PWM_ASPEED_DUTY_CYCLE);
+ }
+
+ writel((readl(priv->base + PWM_ASPEED_CTRL) &
+ ~(PWM_ASPEED_CTRL_CLK_DIV_H | PWM_ASPEED_CTRL_CLK_DIV_L |
+ PWM_ASPEED_CTRL_PIN_ENABLE | PWM_ASPEED_CTRL_CLK_ENABLE |
+ PWM_ASPEED_CTRL_INVERSE)) |
+ FIELD_PREP(PWM_ASPEED_CTRL_CLK_DIV_H, div_h) |
+ FIELD_PREP(PWM_ASPEED_CTRL_CLK_DIV_L, div_l) |
+ FIELD_PREP(PWM_ASPEED_CTRL_PIN_ENABLE, state->enabled) |
+ FIELD_PREP(PWM_ASPEED_CTRL_CLK_ENABLE, clk_en) |
+ FIELD_PREP(PWM_ASPEED_CTRL_INVERSE, state->polarity),
+ priv->base + PWM_ASPEED_CTRL);
+
+ return 0;
+}
+
+static const struct pwm_ops aspeed_pwm_ops = {
+ .apply = aspeed_pwm_apply,
+ .get_state = aspeed_pwm_get_state,
+ .owner = THIS_MODULE,
+};
+
+static void aspeed_pwm_reset_assert(void *data)
+{
+ struct reset_control *rst = data;
+
+ reset_control_assert(rst);
+}
+
+static void aspeed_pwm_chip_remove(void *data)
+{
+ struct pwm_chip *chip = data;
+
+ pwmchip_remove(chip);
+}
+
+static int aspeed_pwm_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ int ret;
+ struct aspeed_pwm_data *priv;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(priv->base))
+ return PTR_ERR(priv->base);
+
+ priv->clk = devm_clk_get_enabled(dev, NULL);
+ if (IS_ERR(priv->clk))
+ return dev_err_probe(dev, PTR_ERR(priv->clk),
+ "Couldn't get clock\n");
+ priv->clk_source = clk_get_rate(priv->clk);
+ priv->reset = devm_reset_control_get_shared(dev, NULL);
+ if (IS_ERR(priv->reset))
+ return dev_err_probe(dev, PTR_ERR(priv->reset),
+ "Couldn't get reset control\n");
+
+ ret = reset_control_deassert(priv->reset);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Couldn't deassert reset control\n");
+
+ ret = devm_add_action_or_reset(dev, aspeed_pwm_reset_assert,
+ priv->reset);
+ if (ret)
+ return ret;
+
+ priv->chip.dev = dev;
+ priv->chip.ops = &aspeed_pwm_ops;
+ priv->chip.npwm = 1;
+
+ ret = pwmchip_add(&priv->chip);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "Failed to add PWM chip\n");
+ ret = devm_add_action_or_reset(dev, aspeed_pwm_chip_remove,
+ &priv->chip);
+ if (ret)
+ return ret;
+ return 0;
+}
+
+static const struct of_device_id of_pwm_match_table[] = {
+ {
+ .compatible = "aspeed,ast2600-pwm",
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, of_pwm_match_table);
+
+static struct platform_driver aspeed_pwm_driver = {
+ .probe = aspeed_pwm_probe,
+ .driver = {
+ .name = "aspeed-pwm",
+ .of_match_table = of_pwm_match_table,
+ },
+};
+
+module_platform_driver(aspeed_pwm_driver);
+
+MODULE_AUTHOR("Billy Tsai <billy_tsai@aspeedtech.com>");
+MODULE_DESCRIPTION("Aspeed ast2600 PWM device driver");
+MODULE_LICENSE("GPL");