diff mbox series

[v4,4/6] phy/rockchip: inno-hdmi: do not power on rk3328 post pll on reg write

Message ID 20230615171005.2251032-5-jonas@kwiboo.se (mailing list archive)
State New, archived
Headers show
Series Support more HDMI modes on RK3228/RK3328 | expand

Commit Message

Jonas Karlman June 15, 2023, 5:10 p.m. UTC 
inno_write is used to configure 0xaa reg, that also hold the
POST_PLL_POWER_DOWN bit.
When POST_PLL_REFCLK_SEL_TMDS is configured the power down bit is not
taken into consideration.

Fix this by keeping the power down bit until configuration is complete.
Also reorder the reg write order for consistency.

Fixes: 53706a116863 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
---
v3:
- no change

 drivers/phy/rockchip/phy-rockchip-inno-hdmi.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
diff mbox series

Patch

diff --git a/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c b/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
index f027e0a2e26b..fe7fa9a43ec0 100644
--- a/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
+++ b/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
@@ -1020,9 +1020,10 @@  inno_hdmi_phy_rk3328_power_on(struct inno_hdmi_phy *inno,
 
 	inno_write(inno, 0xac, RK3328_POST_PLL_FB_DIV_7_0(cfg->fbdiv));
 	if (cfg->postdiv == 1) {
-		inno_write(inno, 0xaa, RK3328_POST_PLL_REFCLK_SEL_TMDS);
 		inno_write(inno, 0xab, RK3328_POST_PLL_FB_DIV_8(cfg->fbdiv) |
 			   RK3328_POST_PLL_PRE_DIV(cfg->prediv));
+		inno_write(inno, 0xaa, RK3328_POST_PLL_REFCLK_SEL_TMDS |
+			   RK3328_POST_PLL_POWER_DOWN);
 	} else {
 		v = (cfg->postdiv / 2) - 1;
 		v &= RK3328_POST_PLL_POST_DIV_MASK;
@@ -1030,7 +1031,8 @@  inno_hdmi_phy_rk3328_power_on(struct inno_hdmi_phy *inno,
 		inno_write(inno, 0xab, RK3328_POST_PLL_FB_DIV_8(cfg->fbdiv) |
 			   RK3328_POST_PLL_PRE_DIV(cfg->prediv));
 		inno_write(inno, 0xaa, RK3328_POST_PLL_POST_DIV_ENABLE |
-			   RK3328_POST_PLL_REFCLK_SEL_TMDS);
+			   RK3328_POST_PLL_REFCLK_SEL_TMDS |
+			   RK3328_POST_PLL_POWER_DOWN);
 	}
 
 	for (v = 0; v < 14; v++)