@@ -42,8 +42,8 @@ &A53_3 {
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec>;
- phy-mode = "rgmii-id";
phy-handle = <ðphy1>;
+ phy-mode = "rgmii-id";
fsl,magic-packet;
status = "okay";
@@ -54,12 +54,12 @@ mdio {
ethphy1: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
- ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
- ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
- ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ enet-phy-lane-no-swap;
ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
ti,min-output-impedance;
- enet-phy-lane-no-swap;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
};
};
};
@@ -73,8 +73,8 @@ som_flash: flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <80000000>;
- spi-tx-bus-width = <1>;
spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
};
};
@@ -83,89 +83,89 @@ &i2c1 {
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
- sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
pmic: pmic@25 {
- reg = <0x25>;
compatible = "nxp,pca9450c";
+ reg = <0x25>;
+ interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pmic>;
- interrupt-parent = <&gpio4>;
- interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
regulators {
buck1: BUCK1 {
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <2187500>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <2187500>;
+ regulator-min-microvolt = <600000>;
regulator-ramp-delay = <3125>;
};
buck2: BUCK2 {
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <2187500>;
- regulator-boot-on;
- regulator-always-on;
- regulator-ramp-delay = <3125>;
nxp,dvs-run-voltage = <950000>;
nxp,dvs-standby-voltage = <850000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <2187500>;
+ regulator-min-microvolt = <600000>;
+ regulator-ramp-delay = <3125>;
};
buck4: BUCK4 {
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <3400000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3400000>;
+ regulator-min-microvolt = <600000>;
};
buck5: BUCK5 {
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <3400000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3400000>;
+ regulator-min-microvolt = <600000>;
};
buck6: BUCK6 {
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <3400000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3400000>;
+ regulator-min-microvolt = <600000>;
};
ldo1: LDO1 {
- regulator-min-microvolt = <1600000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <1600000>;
};
ldo2: LDO2 {
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1150000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1150000>;
+ regulator-min-microvolt = <800000>;
};
ldo3: LDO3 {
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <800000>;
};
ldo4: LDO4 {
- regulator-min-microvolt = <800000>;
regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <800000>;
};
ldo5: LDO5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <1800000>;
};
};
};
@@ -213,13 +213,13 @@ MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91
MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91
MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91
MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91
- MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91
MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x12
MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x12
MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x14
MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x14
MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x14
MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x14
+ MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91
>;
};
@@ -236,8 +236,8 @@ MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03 0x82
pinctrl_i2c1: i2c1grp {
fsl,pins = <
- MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c3
MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c3
+ MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c3
>;
};
@@ -256,49 +256,49 @@ MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x141
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
- MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190
- MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0
MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0
MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0
MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0
MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0
MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0
- MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0
- MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0
- MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0
- MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0
>;
};
pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
fsl,pins = <
- MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194
- MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4
MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4
MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4
MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4
MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4
MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4
- MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4
- MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4
- MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4
- MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4
>;
};
pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
fsl,pins = <
- MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196
- MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d2
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d2
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d2
MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d2
MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d2
MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d2
MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d2
MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d2
- MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d2
- MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d2
- MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d2
- MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6
>;
};
Rearrange properties in order: - compatible - reg - other generic properties - device specific properties - vendor specific properties - status And use alphabetical order inside a group. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> --- Changes in v2: - Rearranged nodes as suggested by Shawn - Updated commit message accordingly --- .../dts/freescale/imx8mp-phycore-som.dtsi | 120 +++++++++--------- 1 file changed, 60 insertions(+), 60 deletions(-)