@@ -105,6 +105,7 @@ struct ddr_pmu {
const struct fsl_ddr_devtype_data *devtype_data;
int irq;
int id;
+ int active_counter;
};
static ssize_t ddr_perf_identifier_show(struct device *dev,
@@ -516,6 +517,10 @@ static void ddr_perf_event_start(struct perf_event *event, int flags)
ddr_perf_counter_enable(pmu, event->attr.config, counter, true);
+ if (!pmu->active_counter++)
+ ddr_perf_counter_enable(pmu, EVENT_CYCLES_ID,
+ EVENT_CYCLES_COUNTER, true);
+
hwc->state = 0;
}
@@ -569,6 +574,10 @@ static void ddr_perf_event_stop(struct perf_event *event, int flags)
ddr_perf_counter_enable(pmu, event->attr.config, counter, false);
ddr_perf_event_update(event);
+ if (!--pmu->active_counter)
+ ddr_perf_counter_enable(pmu, EVENT_CYCLES_ID,
+ EVENT_CYCLES_COUNTER, false);
+
hwc->state |= PERF_HES_STOPPED;
}
@@ -586,25 +595,10 @@ static void ddr_perf_event_del(struct perf_event *event, int flags)
static void ddr_perf_pmu_enable(struct pmu *pmu)
{
- struct ddr_pmu *ddr_pmu = to_ddr_pmu(pmu);
-
- /* enable cycle counter if cycle is not active event list */
- if (ddr_pmu->events[EVENT_CYCLES_COUNTER] == NULL)
- ddr_perf_counter_enable(ddr_pmu,
- EVENT_CYCLES_ID,
- EVENT_CYCLES_COUNTER,
- true);
}
static void ddr_perf_pmu_disable(struct pmu *pmu)
{
- struct ddr_pmu *ddr_pmu = to_ddr_pmu(pmu);
-
- if (ddr_pmu->events[EVENT_CYCLES_COUNTER] == NULL)
- ddr_perf_counter_enable(ddr_pmu,
- EVENT_CYCLES_ID,
- EVENT_CYCLES_COUNTER,
- false);
}
static int ddr_perf_init(struct ddr_pmu *pmu, void __iomem *base,
In current driver, counter0 will be enabled after ddr_perf_pmu_enable() is called even though none of the 4 counters are used. This will cause counter0 continue to count until ddr_perf_pmu_disabled() is called. If pmu is not disabled all the time, the pmu interrupt will be asserted from time to time due to counter0 will overflow and irq handler will clear it. It's not an expected behavior. This patch will not enable counter0 if none of 4 counters are used. Fixes: 9a66d36cc7ac ("drivers/perf: imx_ddr: Add DDR performance counter support to perf") Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> --- Changes in v5: - no change Changes in v4: - enable cycle counter when active_counter from 0 -> 1 - disable cycle counter when active_counter from 1 -> 0 - make ddr_perf_pmu_enable/disable() an empty function Changes in v3: - don't differentiate cycle counter and other counters - modify logic in pmu_enable()/pmu_disable() Changes in v2: - add active counter count as suggested from Frank --- drivers/perf/fsl_imx8_ddr_perf.c | 24 +++++++++--------------- 1 file changed, 9 insertions(+), 15 deletions(-)