| Message ID | 20230817131352.17631-1-mihai.sain@microchip.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v3] ARM: dts: at91: sama5d29_curiosity: Add device tree for sama5d29_curiosity board | expand |
Hi, Mihai, On 17.08.2023 16:13, Mihai Sain wrote: > Add initial device tree file for sama5d29_curiosity board. > > Signed-off-by: Mihai Sain <mihai.sain@microchip.com> > --- I would apply this but there are some warnings like: /home/claudiu/repos/linux-microchip/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dtb: leds: 'blue', 'green', 'red' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' /home/claudiu/repos/linux-microchip/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dtb: pinctrl@fc038000: i2c0-gpio: {'pinmux': [[63, 64]], 'bias-disable': True, 'phandle': [[23]]} is not of type 'array' from schema $id: http://devicetree.org/schemas/gpio/gpio-consumer.yaml# /home/claudiu/repos/linux-microchip/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dtb: pinctrl@fc038000: i2c1-gpio: {'pinmux': [[100, 101]], 'bias-disable': True, 'phandle': [[36]]} is not of type 'array' Can you, please, run make dtbs_check arch/arm/boot/dts/microchip and fix the warnings introduced by your dts (not the ones comming from dtsi at the moment)? Thank you, Claudiu Beznea > Changes in v3: > * remove i2s0 node and its pinctrl > > Changes in v2: > * drop dt-bindings patch > * remove vdd_1v8 regulator > * fix flx4 node to use 1 spi node and pinctrl > * add i2s0 node and pinctrl > * remove macb0 node and pinctrl > * remove unused pinctrl > * sort in alphabetical order all nodes and pinctrl > * replace "_" with "-" in node names > --- > arch/arm/boot/dts/microchip/Makefile | 2 + > .../dts/microchip/at91-sama5d29_curiosity.dts | 600 ++++++++++++++++++ > 2 files changed, 602 insertions(+) > create mode 100644 arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts > > diff --git a/arch/arm/boot/dts/microchip/Makefile b/arch/arm/boot/dts/microchip/Makefile > index 31e03747cdf4..efde9546c8f4 100644 > --- a/arch/arm/boot/dts/microchip/Makefile > +++ b/arch/arm/boot/dts/microchip/Makefile > @@ -4,6 +4,7 @@ DTC_FLAGS_at91-sam9x60_curiosity := -@ > DTC_FLAGS_at91-sam9x60ek := -@ > DTC_FLAGS_at91-sama5d27_som1_ek := -@ > DTC_FLAGS_at91-sama5d27_wlsom1_ek := -@ > +DTC_FLAGS_at91-sama5d29_curiosity := -@ > DTC_FLAGS_at91-sama5d2_icp := -@ > DTC_FLAGS_at91-sama5d2_ptc_ek := -@ > DTC_FLAGS_at91-sama5d2_xplained := -@ > @@ -64,6 +65,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \ > at91-nattis-2-natte-2.dtb \ > at91-sama5d27_som1_ek.dtb \ > at91-sama5d27_wlsom1_ek.dtb \ > + at91-sama5d29_curiosity.dtb \ > at91-sama5d2_icp.dtb \ > at91-sama5d2_ptc_ek.dtb \ > at91-sama5d2_xplained.dtb \ > diff --git a/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts > new file mode 100644 > index 000000000000..267e1dbb417d > --- /dev/null > +++ b/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts > @@ -0,0 +1,600 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * at91-sama5d29_curiosity.dts - Device Tree file for SAMA5D29 Curiosity board > + * > + * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries > + * > + * Author: Mihai Sain <mihai.sain@microchip.com> > + * > + */ > +/dts-v1/; > +#include "sama5d29.dtsi" > +#include "sama5d2-pinfunc.h" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/mfd/atmel-flexcom.h> > + > +/ { > + model = "Microchip SAMA5D29 Curiosity"; > + compatible = "microchip,sama5d29-curiosity", "atmel,sama5d29", "atmel,sama5d2", "atmel,sama5"; > + > + aliases { > + serial0 = &uart0; // debug > + serial1 = &uart1; // RPi > + serial2 = &uart3; // mikro BUS 2 > + serial3 = &uart4; // mikro BUS 1 > + serial4 = &uart6; // flx1 Bluetooth > + i2c0 = &i2c0; > + i2c1 = &i2c1; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"; > + stdout-path = "serial0:115200n8"; > + }; > + > + clocks { > + slow_xtal { > + clock-frequency = <32768>; > + }; > + > + main_xtal { > + clock-frequency = <24000000>; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_key_gpio_default>; > + > + button-1 { > + label = "USER BUTTON"; > + gpios = <&pioA PIN_PA17 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_PROG1>; > + wakeup-source; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_led_gpio_default>; > + status = "okay"; > + > + red { > + label = "red"; > + gpios = <&pioA PIN_PA7 GPIO_ACTIVE_HIGH>; > + }; > + > + green { > + label = "green"; > + gpios = <&pioA PIN_PA8 GPIO_ACTIVE_HIGH>; > + }; > + > + blue { > + label = "blue"; > + gpios = <&pioA PIN_PA9 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + }; > + }; > + > + memory@20000000 { > + device_type = "memory"; > + reg = <0x20000000 0x20000000>; > + }; > +}; > + > +&adc { > + vddana-supply = <&vdd_3v3>; > + vref-supply = <&vdd_3v3>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>; > + status = "okay"; > +}; > + > +&can0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_can0_default>; > + status = "okay"; > +}; > + > +&can1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_can1_default>; > + status = "okay"; > +}; > + > +&flx1 { > + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>; > + status = "okay"; > + > + uart6: serial@200 { > + pinctrl-0 = <&pinctrl_flx1_default>; > + pinctrl-names = "default"; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + status = "okay"; > + }; > +}; > + > +&flx4 { > + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>; > + status = "okay"; > + > + spi6: spi@400 { > + dmas = <0>, <0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_rpi_spi>; > + status = "okay"; > + }; > +}; > + > +&i2c0 { > + dmas = <0>, <0>; > + pinctrl-names = "default", "gpio"; > + pinctrl-0 = <&pinctrl_i2c0_default>; > + pinctrl-1 = <&pinctrl_i2c0_gpio>; > + sda-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_HIGH>; > + scl-gpios = <&pioA PIN_PC0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-sda-hold-time-ns = <350>; > + status = "okay"; > + > + mcp16502@5b { > + compatible = "microchip,mcp16502"; > + reg = <0x5b>; > + status = "okay"; > + lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>; > + > + regulators { > + vdd_3v3: VDD_IO { > + regulator-name = "VDD_IO"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-initial-mode = <2>; > + regulator-allowed-modes = <2>, <4>; > + regulator-always-on; > + > + regulator-state-standby { > + regulator-on-in-suspend; > + regulator-mode = <4>; > + }; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + regulator-mode = <4>; > + }; > + }; > + > + vddio_ddr: VDD_DDR { > + regulator-name = "VDD_DDR"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <2>; > + regulator-allowed-modes = <2>, <4>; > + regulator-always-on; > + > + regulator-state-standby { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1200000>; > + regulator-changeable-in-suspend; > + regulator-mode = <4>; > + }; > + > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1200000>; > + regulator-changeable-in-suspend; > + regulator-mode = <4>; > + }; > + }; > + > + vdd_core: VDD_CORE { > + regulator-name = "VDD_CORE"; > + regulator-min-microvolt = <1250000>; > + regulator-max-microvolt = <1250000>; > + regulator-initial-mode = <2>; > + regulator-allowed-modes = <2>, <4>; > + regulator-always-on; > + > + regulator-state-standby { > + regulator-on-in-suspend; > + regulator-mode = <4>; > + }; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + regulator-mode = <4>; > + }; > + }; > + > + vdd_ddr: VDD_OTHER { > + regulator-name = "VDD_OTHER"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <2>; > + regulator-allowed-modes = <2>, <4>; > + regulator-always-on; > + > + regulator-state-standby { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1800000>; > + regulator-changeable-in-suspend; > + regulator-mode = <4>; > + }; > + > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1800000>; > + regulator-changeable-in-suspend; > + regulator-mode = <4>; > + }; > + }; > + > + LDO1 { > + regulator-name = "LDO1"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + regulator-always-on; > + > + regulator-state-standby { > + regulator-on-in-suspend; > + }; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + LDO2 { > + regulator-name = "LDO2"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + > + regulator-state-standby { > + regulator-on-in-suspend; > + }; > + > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + }; > + }; > +}; > + > +&i2c1 { > + dmas = <0>, <0>; > + pinctrl-names = "default", "gpio"; > + pinctrl-0 = <&pinctrl_i2c1_default>; > + pinctrl-1 = <&pinctrl_i2c1_gpio>; > + i2c-analog-filter; > + i2c-digital-filter; > + i2c-digital-filter-width-ns = <35>; > + sda-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_HIGH>; > + scl-gpios = <&pioA PIN_PD5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + status = "okay"; > +}; > + > +&pioA { > + pinctrl_adc_default: adc-default { > + pinmux = <PIN_PD25__GPIO>, > + <PIN_PD26__GPIO>; > + bias-disable; > + }; > + > + pinctrl_adtrg_default: adtrg-default { > + pinmux = <PIN_PD31__ADTRG>; > + bias-pull-up; > + }; > + > + pinctrl_can0_default: can0-default { > + pinmux = <PIN_PC10__CANTX0>, > + <PIN_PC11__CANRX0>; > + bias-disable; > + }; > + > + pinctrl_can1_default: can1-default { > + pinmux = <PIN_PC26__CANTX1>, > + <PIN_PC27__CANRX1>; > + bias-disable; > + }; > + > + pinctrl_debug_uart: debug-uart { > + pinmux = <PIN_PB26__URXD0>, > + <PIN_PB27__UTXD0>; > + bias-disable; > + }; > + > + pinctrl_flx1_default: flx1-default { > + pinmux = <PIN_PA24__FLEXCOM1_IO0>, > + <PIN_PA23__FLEXCOM1_IO1>, > + <PIN_PA25__FLEXCOM1_IO3>, > + <PIN_PA26__FLEXCOM1_IO4>; > + bias-disable; > + }; > + > + pinctrl_i2c0_default: i2c0-default { > + pinmux = <PIN_PB31__TWD0>, > + <PIN_PC0__TWCK0>; > + bias-disable; > + }; > + > + pinctrl_i2c0_gpio: i2c0-gpio { > + pinmux = <PIN_PB31__GPIO>, > + <PIN_PC0__GPIO>; > + bias-disable; > + }; > + > + pinctrl_i2c1_default: i2c1-default { > + pinmux = <PIN_PD4__TWD1>, > + <PIN_PD5__TWCK1>; > + bias-disable; > + }; > + > + pinctrl_i2c1_gpio: i2c1-gpio { > + pinmux = <PIN_PD4__GPIO>, > + <PIN_PD5__GPIO>; > + bias-disable; > + }; > + > + pinctrl_key_gpio_default: key-gpio-default { > + pinmux = <PIN_PA17__GPIO>; > + bias-pull-up; > + }; > + > + pinctrl_led_gpio_default: led-gpio-default { > + pinmux = <PIN_PA7__GPIO>, > + <PIN_PA8__GPIO>, > + <PIN_PA9__GPIO>; > + bias-pull-up; > + }; > + > + pinctrl_mikrobus1_pwm: mikrobus1-pwm { > + pinmux = <PIN_PA31__PWML0>; > + bias-disable; > + }; > + > + pinctrl_mikrobus2_pwm: mikrobus2-pwm { > + pinmux = <PIN_PB0__PWMH1>; > + bias-disable; > + }; > + > + pinctrl_mikrobus1_uart: mikrobus1-uart { > + pinmux = <PIN_PB3__URXD4>, > + <PIN_PB4__UTXD4>; > + bias-disable; > + }; > + > + pinctrl_mikrobus2_uart: mikrobus2-uart { > + pinmux = <PIN_PB11__URXD3>, > + <PIN_PB12__UTXD3>; > + bias-disable; > + }; > + > + pinctrl_qspi1_default: qspi1-default { > + pinmux = <PIN_PB5__QSPI1_SCK>, > + <PIN_PB6__QSPI1_CS>, > + <PIN_PB7__QSPI1_IO0>, > + <PIN_PB8__QSPI1_IO1>, > + <PIN_PB9__QSPI1_IO2>, > + <PIN_PB10__QSPI1_IO3>; > + bias-disable; > + }; > + > + pinctrl_rpi_spi: rpi-spi { > + pinmux = <PIN_PD12__FLEXCOM4_IO0>, > + <PIN_PD13__FLEXCOM4_IO1>, > + <PIN_PD14__FLEXCOM4_IO2>, > + <PIN_PD15__FLEXCOM4_IO3>, > + <PIN_PD16__FLEXCOM4_IO4>; > + bias-disable; > + }; > + > + pinctrl_rpi_uart: rpi-uart { > + pinmux = <PIN_PD2__URXD1>, > + <PIN_PD3__UTXD1>; > + bias-disable; > + }; > + > + pinctrl_sdmmc0_default: sdmmc0-default { > + pinmux = <PIN_PA0__SDMMC0_CK>, > + <PIN_PA1__SDMMC0_CMD>, > + <PIN_PA2__SDMMC0_DAT0>, > + <PIN_PA3__SDMMC0_DAT1>, > + <PIN_PA4__SDMMC0_DAT2>, > + <PIN_PA5__SDMMC0_DAT3>, > + <PIN_PA11__SDMMC0_VDDSEL>, > + <PIN_PA13__SDMMC0_CD>; > + bias-disable; > + }; > + > + pinctrl_sdmmc1_default: sdmmc1-default { > + pinmux = <PIN_PA18__SDMMC1_DAT0>, > + <PIN_PA19__SDMMC1_DAT1>, > + <PIN_PA20__SDMMC1_DAT2>, > + <PIN_PA21__SDMMC1_DAT3>, > + <PIN_PA22__SDMMC1_CK>, > + <PIN_PA28__SDMMC1_CMD>, > + <PIN_PA30__SDMMC1_CD>; > + bias-disable; > + }; > + > + pinctrl_spi1_default: spi1-default { > + pinmux = <PIN_PC1__SPI1_SPCK>, > + <PIN_PC2__SPI1_MOSI>, > + <PIN_PC3__SPI1_MISO>, > + <PIN_PC4__SPI1_NPCS0>, > + <PIN_PC5__SPI1_NPCS1>, > + <PIN_PC6__SPI1_NPCS2>, > + <PIN_PC7__SPI1_NPCS3>; > + bias-disable; > + }; > + > + pinctrl_usb_default: usb-default { > + pinmux = <PIN_PA6__GPIO>; > + bias-disable; > + }; > + > + pinctrl_usba_vbus: usba-vbus { > + pinmux = <PIN_PB13__GPIO>; > + bias-disable; > + }; > +}; > + > +&pwm0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_mikrobus1_pwm &pinctrl_mikrobus2_pwm>; > + status = "okay"; > +}; > + > +&qspi1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_qspi1_default>; > + status = "okay"; > + > + flash@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <80000000>; > + spi-tx-bus-width = <4>; > + spi-rx-bus-width = <4>; > + m25p,fast-read; > + label = "atmel_qspi1"; > + status = "okay"; > + > + at91bootstrap@0 { > + label = "at91bootstrap"; > + reg = <0x0 0x40000>; > + }; > + > + bootloader@40000 { > + label = "bootloader"; > + reg = <0x40000 0xc0000>; > + }; > + > + bootloaderenvred@100000 { > + label = "bootloader env redundant"; > + reg = <0x100000 0x40000>; > + }; > + > + bootloaderenv@140000 { > + label = "bootloader env"; > + reg = <0x140000 0x40000>; > + }; > + > + dtb@180000 { > + label = "device tree"; > + reg = <0x180000 0x80000>; > + }; > + > + kernel@200000 { > + label = "kernel"; > + reg = <0x200000 0x600000>; > + }; > + }; > +}; > + > +&sdmmc0 { > + bus-width = <4>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sdmmc0_default>; > + disable-wp; > + status = "okay"; > +}; > + > +&sdmmc1 { > + bus-width = <4>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sdmmc1_default>; > + disable-wp; > + status = "okay"; > +}; > + > +&shutdown_controller { > + debounce-delay-us = <976>; > + atmel,wakeup-rtc-timer; > + > + input@0 { > + reg = <0>; > + }; > +}; > + > +&spi1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi1_default>; > + status = "okay"; > +}; > + > +&tcb0 { > + timer0: timer@0 { > + compatible = "atmel,tcb-timer"; > + reg = <0>; > + }; > + > + timer1: timer@1 { > + compatible = "atmel,tcb-timer"; > + reg = <1>; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_debug_uart>; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + status = "okay"; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_rpi_uart>; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + status = "okay"; > +}; > + > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_mikrobus2_uart>; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + status = "okay"; > +}; > + > +&uart4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_mikrobus1_uart>; > + atmel,use-dma-rx; > + atmel,use-dma-tx; > + status = "okay"; > +}; > + > +&usb0 { > + atmel,vbus-gpio = <&pioA PIN_PB13 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usba_vbus>; > + status = "okay"; > +}; > + > +&usb1 { > + num-ports = <3>; > + atmel,vbus-gpio = <0 > + &pioA PIN_PA6 GPIO_ACTIVE_HIGH > + 0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usb_default>; > + status = "okay"; > +}; > + > +&usb2 { > + status = "okay"; > +}; > + > +&watchdog { > + status = "okay"; > +};
diff --git a/arch/arm/boot/dts/microchip/Makefile b/arch/arm/boot/dts/microchip/Makefile index 31e03747cdf4..efde9546c8f4 100644 --- a/arch/arm/boot/dts/microchip/Makefile +++ b/arch/arm/boot/dts/microchip/Makefile @@ -4,6 +4,7 @@ DTC_FLAGS_at91-sam9x60_curiosity := -@ DTC_FLAGS_at91-sam9x60ek := -@ DTC_FLAGS_at91-sama5d27_som1_ek := -@ DTC_FLAGS_at91-sama5d27_wlsom1_ek := -@ +DTC_FLAGS_at91-sama5d29_curiosity := -@ DTC_FLAGS_at91-sama5d2_icp := -@ DTC_FLAGS_at91-sama5d2_ptc_ek := -@ DTC_FLAGS_at91-sama5d2_xplained := -@ @@ -64,6 +65,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \ at91-nattis-2-natte-2.dtb \ at91-sama5d27_som1_ek.dtb \ at91-sama5d27_wlsom1_ek.dtb \ + at91-sama5d29_curiosity.dtb \ at91-sama5d2_icp.dtb \ at91-sama5d2_ptc_ek.dtb \ at91-sama5d2_xplained.dtb \ diff --git a/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts new file mode 100644 index 000000000000..267e1dbb417d --- /dev/null +++ b/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts @@ -0,0 +1,600 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * at91-sama5d29_curiosity.dts - Device Tree file for SAMA5D29 Curiosity board + * + * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries + * + * Author: Mihai Sain <mihai.sain@microchip.com> + * + */ +/dts-v1/; +#include "sama5d29.dtsi" +#include "sama5d2-pinfunc.h" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/mfd/atmel-flexcom.h> + +/ { + model = "Microchip SAMA5D29 Curiosity"; + compatible = "microchip,sama5d29-curiosity", "atmel,sama5d29", "atmel,sama5d2", "atmel,sama5"; + + aliases { + serial0 = &uart0; // debug + serial1 = &uart1; // RPi + serial2 = &uart3; // mikro BUS 2 + serial3 = &uart4; // mikro BUS 1 + serial4 = &uart6; // flx1 Bluetooth + i2c0 = &i2c0; + i2c1 = &i2c1; + }; + + chosen { + bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"; + stdout-path = "serial0:115200n8"; + }; + + clocks { + slow_xtal { + clock-frequency = <32768>; + }; + + main_xtal { + clock-frequency = <24000000>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_key_gpio_default>; + + button-1 { + label = "USER BUTTON"; + gpios = <&pioA PIN_PA17 GPIO_ACTIVE_LOW>; + linux,code = <KEY_PROG1>; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led_gpio_default>; + status = "okay"; + + red { + label = "red"; + gpios = <&pioA PIN_PA7 GPIO_ACTIVE_HIGH>; + }; + + green { + label = "green"; + gpios = <&pioA PIN_PA8 GPIO_ACTIVE_HIGH>; + }; + + blue { + label = "blue"; + gpios = <&pioA PIN_PA9 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + memory@20000000 { + device_type = "memory"; + reg = <0x20000000 0x20000000>; + }; +}; + +&adc { + vddana-supply = <&vdd_3v3>; + vref-supply = <&vdd_3v3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>; + status = "okay"; +}; + +&can0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can0_default>; + status = "okay"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1_default>; + status = "okay"; +}; + +&flx1 { + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>; + status = "okay"; + + uart6: serial@200 { + pinctrl-0 = <&pinctrl_flx1_default>; + pinctrl-names = "default"; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "okay"; + }; +}; + +&flx4 { + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>; + status = "okay"; + + spi6: spi@400 { + dmas = <0>, <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rpi_spi>; + status = "okay"; + }; +}; + +&i2c0 { + dmas = <0>, <0>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c0_default>; + pinctrl-1 = <&pinctrl_i2c0_gpio>; + sda-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_HIGH>; + scl-gpios = <&pioA PIN_PC0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-sda-hold-time-ns = <350>; + status = "okay"; + + mcp16502@5b { + compatible = "microchip,mcp16502"; + reg = <0x5b>; + status = "okay"; + lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>; + + regulators { + vdd_3v3: VDD_IO { + regulator-name = "VDD_IO"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <2>; + regulator-allowed-modes = <2>, <4>; + regulator-always-on; + + regulator-state-standby { + regulator-on-in-suspend; + regulator-mode = <4>; + }; + + regulator-state-mem { + regulator-off-in-suspend; + regulator-mode = <4>; + }; + }; + + vddio_ddr: VDD_DDR { + regulator-name = "VDD_DDR"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <2>; + regulator-allowed-modes = <2>, <4>; + regulator-always-on; + + regulator-state-standby { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1200000>; + regulator-changeable-in-suspend; + regulator-mode = <4>; + }; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1200000>; + regulator-changeable-in-suspend; + regulator-mode = <4>; + }; + }; + + vdd_core: VDD_CORE { + regulator-name = "VDD_CORE"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-initial-mode = <2>; + regulator-allowed-modes = <2>, <4>; + regulator-always-on; + + regulator-state-standby { + regulator-on-in-suspend; + regulator-mode = <4>; + }; + + regulator-state-mem { + regulator-off-in-suspend; + regulator-mode = <4>; + }; + }; + + vdd_ddr: VDD_OTHER { + regulator-name = "VDD_OTHER"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <2>; + regulator-allowed-modes = <2>, <4>; + regulator-always-on; + + regulator-state-standby { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + regulator-changeable-in-suspend; + regulator-mode = <4>; + }; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + regulator-changeable-in-suspend; + regulator-mode = <4>; + }; + }; + + LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + + regulator-state-standby { + regulator-on-in-suspend; + }; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + + regulator-state-standby { + regulator-on-in-suspend; + }; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&i2c1 { + dmas = <0>, <0>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c1_default>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + i2c-analog-filter; + i2c-digital-filter; + i2c-digital-filter-width-ns = <35>; + sda-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_HIGH>; + scl-gpios = <&pioA PIN_PD5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; +}; + +&pioA { + pinctrl_adc_default: adc-default { + pinmux = <PIN_PD25__GPIO>, + <PIN_PD26__GPIO>; + bias-disable; + }; + + pinctrl_adtrg_default: adtrg-default { + pinmux = <PIN_PD31__ADTRG>; + bias-pull-up; + }; + + pinctrl_can0_default: can0-default { + pinmux = <PIN_PC10__CANTX0>, + <PIN_PC11__CANRX0>; + bias-disable; + }; + + pinctrl_can1_default: can1-default { + pinmux = <PIN_PC26__CANTX1>, + <PIN_PC27__CANRX1>; + bias-disable; + }; + + pinctrl_debug_uart: debug-uart { + pinmux = <PIN_PB26__URXD0>, + <PIN_PB27__UTXD0>; + bias-disable; + }; + + pinctrl_flx1_default: flx1-default { + pinmux = <PIN_PA24__FLEXCOM1_IO0>, + <PIN_PA23__FLEXCOM1_IO1>, + <PIN_PA25__FLEXCOM1_IO3>, + <PIN_PA26__FLEXCOM1_IO4>; + bias-disable; + }; + + pinctrl_i2c0_default: i2c0-default { + pinmux = <PIN_PB31__TWD0>, + <PIN_PC0__TWCK0>; + bias-disable; + }; + + pinctrl_i2c0_gpio: i2c0-gpio { + pinmux = <PIN_PB31__GPIO>, + <PIN_PC0__GPIO>; + bias-disable; + }; + + pinctrl_i2c1_default: i2c1-default { + pinmux = <PIN_PD4__TWD1>, + <PIN_PD5__TWCK1>; + bias-disable; + }; + + pinctrl_i2c1_gpio: i2c1-gpio { + pinmux = <PIN_PD4__GPIO>, + <PIN_PD5__GPIO>; + bias-disable; + }; + + pinctrl_key_gpio_default: key-gpio-default { + pinmux = <PIN_PA17__GPIO>; + bias-pull-up; + }; + + pinctrl_led_gpio_default: led-gpio-default { + pinmux = <PIN_PA7__GPIO>, + <PIN_PA8__GPIO>, + <PIN_PA9__GPIO>; + bias-pull-up; + }; + + pinctrl_mikrobus1_pwm: mikrobus1-pwm { + pinmux = <PIN_PA31__PWML0>; + bias-disable; + }; + + pinctrl_mikrobus2_pwm: mikrobus2-pwm { + pinmux = <PIN_PB0__PWMH1>; + bias-disable; + }; + + pinctrl_mikrobus1_uart: mikrobus1-uart { + pinmux = <PIN_PB3__URXD4>, + <PIN_PB4__UTXD4>; + bias-disable; + }; + + pinctrl_mikrobus2_uart: mikrobus2-uart { + pinmux = <PIN_PB11__URXD3>, + <PIN_PB12__UTXD3>; + bias-disable; + }; + + pinctrl_qspi1_default: qspi1-default { + pinmux = <PIN_PB5__QSPI1_SCK>, + <PIN_PB6__QSPI1_CS>, + <PIN_PB7__QSPI1_IO0>, + <PIN_PB8__QSPI1_IO1>, + <PIN_PB9__QSPI1_IO2>, + <PIN_PB10__QSPI1_IO3>; + bias-disable; + }; + + pinctrl_rpi_spi: rpi-spi { + pinmux = <PIN_PD12__FLEXCOM4_IO0>, + <PIN_PD13__FLEXCOM4_IO1>, + <PIN_PD14__FLEXCOM4_IO2>, + <PIN_PD15__FLEXCOM4_IO3>, + <PIN_PD16__FLEXCOM4_IO4>; + bias-disable; + }; + + pinctrl_rpi_uart: rpi-uart { + pinmux = <PIN_PD2__URXD1>, + <PIN_PD3__UTXD1>; + bias-disable; + }; + + pinctrl_sdmmc0_default: sdmmc0-default { + pinmux = <PIN_PA0__SDMMC0_CK>, + <PIN_PA1__SDMMC0_CMD>, + <PIN_PA2__SDMMC0_DAT0>, + <PIN_PA3__SDMMC0_DAT1>, + <PIN_PA4__SDMMC0_DAT2>, + <PIN_PA5__SDMMC0_DAT3>, + <PIN_PA11__SDMMC0_VDDSEL>, + <PIN_PA13__SDMMC0_CD>; + bias-disable; + }; + + pinctrl_sdmmc1_default: sdmmc1-default { + pinmux = <PIN_PA18__SDMMC1_DAT0>, + <PIN_PA19__SDMMC1_DAT1>, + <PIN_PA20__SDMMC1_DAT2>, + <PIN_PA21__SDMMC1_DAT3>, + <PIN_PA22__SDMMC1_CK>, + <PIN_PA28__SDMMC1_CMD>, + <PIN_PA30__SDMMC1_CD>; + bias-disable; + }; + + pinctrl_spi1_default: spi1-default { + pinmux = <PIN_PC1__SPI1_SPCK>, + <PIN_PC2__SPI1_MOSI>, + <PIN_PC3__SPI1_MISO>, + <PIN_PC4__SPI1_NPCS0>, + <PIN_PC5__SPI1_NPCS1>, + <PIN_PC6__SPI1_NPCS2>, + <PIN_PC7__SPI1_NPCS3>; + bias-disable; + }; + + pinctrl_usb_default: usb-default { + pinmux = <PIN_PA6__GPIO>; + bias-disable; + }; + + pinctrl_usba_vbus: usba-vbus { + pinmux = <PIN_PB13__GPIO>; + bias-disable; + }; +}; + +&pwm0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mikrobus1_pwm &pinctrl_mikrobus2_pwm>; + status = "okay"; +}; + +&qspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi1_default>; + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + m25p,fast-read; + label = "atmel_qspi1"; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x40000>; + }; + + bootloader@40000 { + label = "bootloader"; + reg = <0x40000 0xc0000>; + }; + + bootloaderenvred@100000 { + label = "bootloader env redundant"; + reg = <0x100000 0x40000>; + }; + + bootloaderenv@140000 { + label = "bootloader env"; + reg = <0x140000 0x40000>; + }; + + dtb@180000 { + label = "device tree"; + reg = <0x180000 0x80000>; + }; + + kernel@200000 { + label = "kernel"; + reg = <0x200000 0x600000>; + }; + }; +}; + +&sdmmc0 { + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdmmc0_default>; + disable-wp; + status = "okay"; +}; + +&sdmmc1 { + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdmmc1_default>; + disable-wp; + status = "okay"; +}; + +&shutdown_controller { + debounce-delay-us = <976>; + atmel,wakeup-rtc-timer; + + input@0 { + reg = <0>; + }; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; + status = "okay"; +}; + +&tcb0 { + timer0: timer@0 { + compatible = "atmel,tcb-timer"; + reg = <0>; + }; + + timer1: timer@1 { + compatible = "atmel,tcb-timer"; + reg = <1>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_debug_uart>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rpi_uart>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mikrobus2_uart>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mikrobus1_uart>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "okay"; +}; + +&usb0 { + atmel,vbus-gpio = <&pioA PIN_PB13 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usba_vbus>; + status = "okay"; +}; + +&usb1 { + num-ports = <3>; + atmel,vbus-gpio = <0 + &pioA PIN_PA6 GPIO_ACTIVE_HIGH + 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_default>; + status = "okay"; +}; + +&usb2 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +};
Add initial device tree file for sama5d29_curiosity board. Signed-off-by: Mihai Sain <mihai.sain@microchip.com> --- Changes in v3: * remove i2s0 node and its pinctrl Changes in v2: * drop dt-bindings patch * remove vdd_1v8 regulator * fix flx4 node to use 1 spi node and pinctrl * add i2s0 node and pinctrl * remove macb0 node and pinctrl * remove unused pinctrl * sort in alphabetical order all nodes and pinctrl * replace "_" with "-" in node names --- arch/arm/boot/dts/microchip/Makefile | 2 + .../dts/microchip/at91-sama5d29_curiosity.dts | 600 ++++++++++++++++++ 2 files changed, 602 insertions(+) create mode 100644 arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts