[tty,v1,63/74] serial: st-asc: Use port lock wrappers

Commit Message

John Ogness Sept. 14, 2023, 6:38 p.m. UTC

From: Thomas Gleixner <[e-mail]>

When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.

So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.

All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.

To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.

Converted with coccinelle. No functional change.

Signed-off-by: Thomas Gleixner <[e-mail]>
---
 drivers/tty/serial/st-asc.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

Patch

diff --git a/drivers/tty/serial/st-asc.c b/drivers/tty/serial/st-asc.c
index 92b9f6894006..a821f5d76a26 100644
--- a/drivers/tty/serial/st-asc.c
+++ b/drivers/tty/serial/st-asc.c
@@ -319,7 +319,7 @@  static irqreturn_t asc_interrupt(int irq, void *ptr)
 	struct uart_port *port = ptr;
 	u32 status;
 
-	spin_lock(&port->lock);
+	uart_port_lock(port);
 
 	status = asc_in(port, ASC_STA);
 
@@ -334,7 +334,7 @@  static irqreturn_t asc_interrupt(int irq, void *ptr)
 		asc_transmit_chars(port);
 	}
 
-	spin_unlock(&port->lock);
+	uart_port_unlock(port);
 
 	return IRQ_HANDLED;
 }
@@ -452,10 +452,10 @@  static void asc_pm(struct uart_port *port, unsigned int state,
 		 * we can come to turning it off. Note this is not called with
 		 * the port spinlock held.
 		 */
-		spin_lock_irqsave(&port->lock, flags);
+		uart_port_lock_irqsave(port, &flags);
 		ctl = asc_in(port, ASC_CTL) & ~ASC_CTL_RUN;
 		asc_out(port, ASC_CTL, ctl);
-		spin_unlock_irqrestore(&port->lock, flags);
+		uart_port_unlock_irqrestore(port, flags);
 		clk_disable_unprepare(ascport->clk);
 		break;
 	}
@@ -480,7 +480,7 @@  static void asc_set_termios(struct uart_port *port, struct ktermios *termios,
 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
 	cflag = termios->c_cflag;
 
-	spin_lock_irqsave(&port->lock, flags);
+	uart_port_lock_irqsave(port, &flags);
 
 	/* read control register */
 	ctrl_val = asc_in(port, ASC_CTL);
@@ -594,7 +594,7 @@  static void asc_set_termios(struct uart_port *port, struct ktermios *termios,
 	/* write final value and enable port */
 	asc_out(port, ASC_CTL, (ctrl_val | ASC_CTL_RUN));
 
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock_irqrestore(port, flags);
 }
 
 static const char *asc_type(struct uart_port *port)
@@ -849,9 +849,9 @@  static void asc_console_write(struct console *co, const char *s, unsigned count)
 	if (port->sysrq)
 		locked = 0; /* asc_interrupt has already claimed the lock */
 	else if (oops_in_progress)
-		locked = spin_trylock_irqsave(&port->lock, flags);
+		locked = uart_port_trylock_irqsave(port, &flags);
 	else
-		spin_lock_irqsave(&port->lock, flags);
+		uart_port_lock_irqsave(port, &flags);
 
 	/*
 	 * Disable interrupts so we don't get the IRQ line bouncing
@@ -869,7 +869,7 @@  static void asc_console_write(struct console *co, const char *s, unsigned count)
 	asc_out(port, ASC_INTEN, intenable);
 
 	if (locked)
-		spin_unlock_irqrestore(&port->lock, flags);
+		uart_port_unlock_irqrestore(port, flags);
 }
 
 static int asc_console_setup(struct console *co, char *options)