diff mbox series

[v2,1/2] arm64: dts: ti: k3-am62p: Add nodes for more IPs

Message ID 20231018194839.2689377-2-bb@ti.com (mailing list archive)
State New, archived
Headers show
Series arm64: dts: ti: enable more peripherals | expand

Commit Message

Bryan Brattlof Oct. 18, 2023, 7:48 p.m. UTC
From: Vignesh Raghavendra <vigneshr@ti.com>

The am62px shares many of the same IP as the existing am62x family
of SoCs, Introduce more nodes for hardware available on the am62p5.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62p-main.dtsi    | 811 ++++++++++++++++++-
 arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi     | 190 +++++
 arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi |  47 ++
 arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi  |  87 +-
 arch/arm64/boot/dts/ti/k3-am62p.dtsi         |   7 +-
 5 files changed, 1130 insertions(+), 12 deletions(-)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi

Comments

Vignesh Raghavendra Oct. 19, 2023, 5:55 a.m. UTC | #1
> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> index aaf4b793b58e7..e37f19f7e58ea 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> @@ -6,17 +6,35 @@
>  
>  &cbass_wakeup {
>  	wkup_conf: bus@43000000 {
> -		bootph-all;
>  		compatible = "simple-bus";
>  		reg = <0x00 0x43000000 0x00 0x20000>;
>  		#address-cells = <1>;
>  		#size-cells = <1>;
>  		ranges = <0x00 0x00 0x43000000 0x20000>;
> +		bootph-all;
>  
>  		chipid: chipid@14 {
> -			bootph-all;
>  			compatible = "ti,am654-chipid";
>  			reg = <0x14 0x4>;
> +			bootph-all;
> +		};
> +
> +		cpsw_efuse: syscon@200 {
> +			compatible = "syscon", "simple-mfd";
> +			reg = <0x200 0x4>;

This holds mac-address which is at least 48bits long

> +			bootph-all;
> +		};
> +
> +		usb0_phy_pll_refclk: syscon@4008 {
> +			compatible = "syscon", "simple-mfd";
> +			reg = <0x4008 0x10>;
> +			bootph-all;
> +		};
> +
> +		usb1_phy_pll_refclk: syscon@4018 {
> +			compatible = "syscon", "simple-mfd";
> +			reg = <0x4018 0x10>;
> +			bootph-all;

This adds new dtbs_check warnings:

+/workdir/arch/arm64/boot/dts/ti/k3-am62p5-sk.dtb: syscon@100000: $nodename:0: 'syscon@100000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
+/workdir/arch/arm64/boot/dts/ti/k3-am62p5-sk.dtb: syscon@200: compatible: ['syscon', 'simple-mfd'] is too short
+/workdir/arch/arm64/boot/dts/ti/k3-am62p5-sk.dtb: syscon@4008: compatible: ['syscon', 'simple-mfd'] is too short
+/workdir/arch/arm64/boot/dts/ti/k3-am62p5-sk.dtb: syscon@4018: compatible: ['syscon', 'simple-mfd'] is too short


I suggest to drop them for now.

Please add a new yamls for these nodes or single yaml for top level wkup_conf to 
cover am62/62a/62p SoCs and then introduce the nodes accordingly

Regards
Vignesh
Bryan Brattlof Oct. 19, 2023, 2:26 p.m. UTC | #2
Hi Vignesh!

On October 19, 2023 thus sayeth Vignesh Raghavendra:
> 
> > diff --git a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> > index aaf4b793b58e7..e37f19f7e58ea 100644
> > --- a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> > @@ -6,17 +6,35 @@
> >  
> >  &cbass_wakeup {
> >  	wkup_conf: bus@43000000 {
> > -		bootph-all;
> >  		compatible = "simple-bus";
> >  		reg = <0x00 0x43000000 0x00 0x20000>;
> >  		#address-cells = <1>;
> >  		#size-cells = <1>;
> >  		ranges = <0x00 0x00 0x43000000 0x20000>;
> > +		bootph-all;
> >  
> >  		chipid: chipid@14 {
> > -			bootph-all;
> >  			compatible = "ti,am654-chipid";
> >  			reg = <0x14 0x4>;
> > +			bootph-all;
> > +		};
> > +
> > +		cpsw_efuse: syscon@200 {
> > +			compatible = "syscon", "simple-mfd";
> > +			reg = <0x200 0x4>;
> 
> This holds mac-address which is at least 48bits long
> 
> > +			bootph-all;
> > +		};
> > +
> > +		usb0_phy_pll_refclk: syscon@4008 {
> > +			compatible = "syscon", "simple-mfd";
> > +			reg = <0x4008 0x10>;
> > +			bootph-all;
> > +		};
> > +
> > +		usb1_phy_pll_refclk: syscon@4018 {
> > +			compatible = "syscon", "simple-mfd";
> > +			reg = <0x4018 0x10>;
> > +			bootph-all;
> 
> This adds new dtbs_check warnings:
> 
> +/workdir/arch/arm64/boot/dts/ti/k3-am62p5-sk.dtb: syscon@100000: $nodename:0: 'syscon@100000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
> +/workdir/arch/arm64/boot/dts/ti/k3-am62p5-sk.dtb: syscon@200: compatible: ['syscon', 'simple-mfd'] is too short
> +/workdir/arch/arm64/boot/dts/ti/k3-am62p5-sk.dtb: syscon@4008: compatible: ['syscon', 'simple-mfd'] is too short
> +/workdir/arch/arm64/boot/dts/ti/k3-am62p5-sk.dtb: syscon@4018: compatible: ['syscon', 'simple-mfd'] is too short
>
> 
> I suggest to drop them for now.
> 
> Please add a new yamls for these nodes or single yaml for top level wkup_conf to 
> cover am62/62a/62p SoCs and then introduce the nodes accordingly
> 

Ah man I didn't see these warnings. Yeah dropping USB and CPSW may be 
the only way for now :/

Thanks again for the review Vignesh
~Bryan
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
index fcbfb1b5242b4..7a53461959709 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
@@ -40,18 +40,37 @@  gic_its: msi-controller@1820000 {
 		};
 	};
 
+	main_conf: syscon@100000 {
+		compatible = "simple-bus";
+		reg = <0x00 0x00100000 0x00 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x00100000 0x20000>;
+
+		phy_gmii_sel: phy@4044 {
+			compatible = "ti,am654-phy-gmii-sel";
+			reg = <0x4044 0x8>;
+			#phy-cells = <1>;
+		};
+
+		epwm_tbclk: clock-controller@4130 {
+			compatible = "ti,am62-epwm-tbclk";
+			reg = <0x4130 0x4>;
+			#clock-cells = <1>;
+		};
+	};
+
 	dmss: bus@48000000 {
-		bootph-all;
 		compatible = "simple-bus";
 		#address-cells = <2>;
 		#size-cells = <2>;
 		dma-ranges;
 		ranges = <0x00 0x48000000 0x00 0x48000000 0x00 0x06400000>;
+		bootph-all;
 
 		ti,sci-dev-id = <25>;
 
 		secure_proxy_main: mailbox@4d000000 {
-			bootph-all;
 			compatible = "ti,am654-secure-proxy";
 			#mbox-cells = <1>;
 			reg-names = "target_data", "rt", "scfg";
@@ -60,11 +79,76 @@  secure_proxy_main: mailbox@4d000000 {
 			      <0x00 0x4a400000 0x00 0x80000>;
 			interrupt-names = "rx_012";
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			bootph-all;
+		};
+
+		inta_main_dmss: interrupt-controller@48000000 {
+			compatible = "ti,sci-inta";
+			reg = <0x00 0x48000000 0x00 0x100000>;
+			#interrupt-cells = <0>;
+			interrupt-controller;
+			interrupt-parent = <&gic500>;
+			msi-controller;
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <28>;
+			ti,interrupt-ranges = <5 69 35>;
+			ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>;
+		};
+
+		main_bcdma: dma-controller@485c0100 {
+			compatible = "ti,am64-dmss-bcdma";
+			reg = <0x00 0x485c0100 0x00 0x100>,
+			      <0x00 0x4c000000 0x00 0x20000>,
+			      <0x00 0x4a820000 0x00 0x20000>,
+			      <0x00 0x4aa40000 0x00 0x20000>,
+			      <0x00 0x4bc00000 0x00 0x100000>;
+			reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt";
+			msi-parent = <&inta_main_dmss>;
+			#dma-cells = <3>;
+
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <26>;
+			ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
+			ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
+			ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
+			bootph-all;
+		};
+
+		main_pktdma: dma-controller@485c0000 {
+			compatible = "ti,am64-dmss-pktdma";
+			reg = <0x00 0x485c0000 0x00 0x100>,
+			      <0x00 0x4a800000 0x00 0x20000>,
+			      <0x00 0x4aa00000 0x00 0x40000>,
+			      <0x00 0x4b800000 0x00 0x400000>;
+			reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt";
+			msi-parent = <&inta_main_dmss>;
+			#dma-cells = <2>;
+			bootph-all;
+
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <30>;
+			ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */
+						<0x24>, /* CPSW_TX_CHAN */
+						<0x25>, /* SAUL_TX_0_CHAN */
+						<0x26>; /* SAUL_TX_1_CHAN */
+			ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */
+						<0x11>, /* RING_CPSW_TX_CHAN */
+						<0x12>, /* RING_SAUL_TX_0_CHAN */
+						<0x13>; /* RING_SAUL_TX_1_CHAN */
+			ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */
+						<0x2b>, /* CPSW_RX_CHAN */
+						<0x2d>, /* SAUL_RX_0_CHAN */
+						<0x2f>, /* SAUL_RX_1_CHAN */
+						<0x31>, /* SAUL_RX_2_CHAN */
+						<0x33>; /* SAUL_RX_3_CHAN */
+			ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */
+						<0x2c>, /* FLOW_CPSW_RX_CHAN */
+						<0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */
+						<0x32>; /* FLOW_SAUL_RX_2/3_CHAN */
 		};
 	};
 
 	dmsc: system-controller@44043000 {
-		bootph-all;
 		compatible = "ti,k2g-sci";
 		ti,host-id = <12>;
 		mbox-names = "rx", "tx";
@@ -72,37 +156,72 @@  dmsc: system-controller@44043000 {
 			 <&secure_proxy_main 13>;
 		reg-names = "debug_messages";
 		reg = <0x00 0x44043000 0x00 0xfe0>;
+		bootph-all;
 
 		k3_pds: power-controller {
-			bootph-all;
 			compatible = "ti,sci-pm-domain";
 			#power-domain-cells = <2>;
+			bootph-all;
 		};
 
 		k3_clks: clock-controller {
-			bootph-all;
 			compatible = "ti,k2g-sci-clk";
 			#clock-cells = <2>;
+			bootph-all;
 		};
 
 		k3_reset: reset-controller {
-			bootph-all;
 			compatible = "ti,sci-reset";
 			#reset-cells = <2>;
+			bootph-all;
 		};
 	};
 
-	main_pmx0: pinctrl@f4000 {
+	crypto: crypto@40900000 {
+		compatible = "ti,am62-sa3ul";
+		reg = <0x00 0x40900000 0x00 0x1200>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0x00 0x40900000 0x00 0x40900000 0x00 0x30000>;
+
+		dmas = <&main_pktdma 0xf501 0>, <&main_pktdma 0x7506 0>,
+		       <&main_pktdma 0x7507 0>;
+		dma-names = "tx", "rx1", "rx2";
+	};
+
+	secure_proxy_sa3: mailbox@43600000 {
+		compatible = "ti,am654-secure-proxy";
+		#mbox-cells = <1>;
+		reg-names = "target_data", "rt", "scfg";
+		reg = <0x00 0x43600000 0x00 0x10000>,
+		      <0x00 0x44880000 0x00 0x20000>,
+		      <0x00 0x44860000 0x00 0x20000>;
+		/*
+		 * Marked Disabled:
+		 * Node is incomplete as it is meant for bootloaders and
+		 * firmware on non-MPU processors
+		 */
+		status = "disabled";
 		bootph-all;
+	};
+
+	main_pmx0: pinctrl@f4000 {
 		compatible = "pinctrl-single";
 		reg = <0x00 0xf4000 0x00 0x2ac>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
 		pinctrl-single,function-mask = <0xffffffff>;
+		bootph-all;
+	};
+
+	main_esm: esm@420000 {
+		compatible = "ti,j721e-esm";
+		reg = <0x00 0x420000 0x00 0x1000>;
+		ti,esm-pins = <160>, <161>, <162>, <163>, <177>, <178>;
+		bootph-pre-ram;
 	};
 
 	main_timer0: timer@2400000 {
-		bootph-all;
 		compatible = "ti,am654-timer";
 		reg = <0x00 0x2400000 0x00 0x400>;
 		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
@@ -112,6 +231,91 @@  main_timer0: timer@2400000 {
 		assigned-clock-parents = <&k3_clks 36 3>;
 		power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>;
 		ti,timer-pwm;
+		bootph-all;
+	};
+
+	main_timer1: timer@2410000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2410000 0x00 0x400>;
+		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 37 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 37 2>;
+		assigned-clock-parents = <&k3_clks 37 3>;
+		power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer2: timer@2420000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2420000 0x00 0x400>;
+		interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 38 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 38 2>;
+		assigned-clock-parents = <&k3_clks 38 3>;
+		power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer3: timer@2430000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2430000 0x00 0x400>;
+		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 39 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 39 2>;
+		assigned-clock-parents = <&k3_clks 39 3>;
+		power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer4: timer@2440000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2440000 0x00 0x400>;
+		interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 40 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 40 2>;
+		assigned-clock-parents = <&k3_clks 40 3>;
+		power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer5: timer@2450000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2450000 0x00 0x400>;
+		interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 41 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 41 2>;
+		assigned-clock-parents = <&k3_clks 41 3>;
+		power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer6: timer@2460000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2460000 0x00 0x400>;
+		interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 42 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 42 2>;
+		assigned-clock-parents = <&k3_clks 42 3>;
+		power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer7: timer@2470000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2470000 0x00 0x400>;
+		interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 43 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 43 2>;
+		assigned-clock-parents = <&k3_clks 43 3>;
+		power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
 	};
 
 	main_uart0: serial@2800000 {
@@ -133,4 +337,595 @@  main_uart1: serial@2810000 {
 		clock-names = "fclk";
 		status = "disabled";
 	};
+
+	main_uart2: serial@2820000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02820000 0x00 0x100>;
+		interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 153 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_uart3: serial@2830000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02830000 0x00 0x100>;
+		interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 154 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_uart4: serial@2840000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02840000 0x00 0x100>;
+		interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 155 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_uart5: serial@2850000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02850000 0x00 0x100>;
+		interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 156 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_uart6: serial@2860000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02860000 0x00 0x100>;
+		interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 158 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_i2c0: i2c@20000000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20000000 0x00 0x100>;
+		interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 102 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	main_i2c1: i2c@20010000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20010000 0x00 0x100>;
+		interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 103 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	main_i2c2: i2c@20020000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20020000 0x00 0x100>;
+		interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 104 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	main_i2c3: i2c@20030000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20030000 0x00 0x100>;
+		interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 105 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	main_spi0: spi@20100000 {
+		compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+		reg = <0x00 0x20100000 0x00 0x400>;
+		interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 141 0>;
+		status = "disabled";
+	};
+
+	main_spi1: spi@20110000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x20110000 0x00 0x400>;
+		interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 142 0>;
+		status = "disabled";
+	};
+
+	main_spi2: spi@20120000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x20120000 0x00 0x400>;
+		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 143 0>;
+		status = "disabled";
+	};
+
+	main_gpio_intr: interrupt-controller@a00000 {
+		compatible = "ti,sci-intr";
+		reg = <0x00 0x00a00000 0x00 0x800>;
+		ti,intr-trigger-type = <1>;
+		interrupt-controller;
+		interrupt-parent = <&gic500>;
+		#interrupt-cells = <1>;
+		ti,sci = <&dmsc>;
+		ti,sci-dev-id = <3>;
+		ti,interrupt-ranges = <0 32 16>;
+	};
+
+	main_gpio0: gpio@600000 {
+		compatible = "ti,am64-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00600000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <190>, <191>, <192>,
+			     <193>, <194>, <195>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <92>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 77 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 77 0>;
+		clock-names = "gpio";
+	};
+
+	main_gpio1: gpio@601000 {
+		compatible = "ti,am64-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00601000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <180>, <181>, <182>,
+			     <183>, <184>, <185>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <52>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 78 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 78 0>;
+		clock-names = "gpio";
+	};
+
+	sdhci0: mmc@fa10000 {
+		compatible = "ti,am64-sdhci-8bit";
+		reg = <0x00 0x0fa10000 0x00 0x1000>, <0x00 0x0fa18000 0x00 0x400>;
+		interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 57 1>, <&k3_clks 57 2>;
+		clock-names = "clk_ahb", "clk_xin";
+		assigned-clocks = <&k3_clks 57 2>;
+		assigned-clock-parents = <&k3_clks 57 4>;
+		ti,otap-del-sel-legacy = <0x0>;
+		status = "disabled";
+	};
+
+	sdhci1: mmc@fa00000 {
+		compatible = "ti,am62-sdhci";
+		reg = <0x00 0x0fa00000 0x00 0x1000>, <0x00 0x0fa08000 0x00 0x400>;
+		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 58 5>, <&k3_clks 58 6>;
+		clock-names = "clk_ahb", "clk_xin";
+		ti,otap-del-sel-legacy = <0x8>;
+		status = "disabled";
+	};
+
+	sdhci2: mmc@fa20000 {
+		compatible = "ti,am62-sdhci";
+		reg = <0x00 0x0fa20000 0x00 0x1000>, <0x00 0x0fa28000 0x00 0x400>;
+		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 184 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 184 5>, <&k3_clks 184 6>;
+		clock-names = "clk_ahb", "clk_xin";
+		ti,otap-del-sel-legacy = <0x8>;
+		status = "disabled";
+	};
+
+	usbss0: dwc3-usb@f900000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f900000 0x00 0x800>;
+		clocks = <&k3_clks 161 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&usb0_phy_pll_refclk 0x00>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb0: usb@31000000 {
+			compatible = "snps,dwc3";
+			reg = <0x00 0x31000000 0x00 0x50000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	usbss1: dwc3-usb@f910000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f910000 0x00 0x800>;
+		clocks = <&k3_clks 162 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&usb1_phy_pll_refclk 0x00>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb1: usb@31100000 {
+			compatible = "snps,dwc3";
+			reg = <0x00 0x31100000 0x00 0x50000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	fss: bus@fc00000 {
+		compatible = "simple-bus";
+		reg = <0x00 0x0fc00000 0x00 0x70000>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ospi0: spi@fc40000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x0fc40000 0x00 0x100>,
+			      <0x05 0x00000000 0x01 0x00000000>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 75 7>;
+			assigned-clocks = <&k3_clks 75 7>;
+			assigned-clock-parents = <&k3_clks 75 8>;
+			assigned-clock-rates = <166666666>;
+			power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+	};
+
+	cpsw3g: ethernet@8000000 {
+		compatible = "ti,am642-cpsw-nuss";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		reg = <0x00 0x08000000 0x00 0x200000>;
+		reg-names = "cpsw_nuss";
+		ranges = <0x00 0x00 0x00 0x08000000 0x00 0x200000>;
+		clocks = <&k3_clks 13 0>;
+		assigned-clocks = <&k3_clks 13 3>;
+		assigned-clock-parents = <&k3_clks 13 11>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
+
+		dmas = <&main_pktdma 0xc600 15>,
+		       <&main_pktdma 0xc601 15>,
+		       <&main_pktdma 0xc602 15>,
+		       <&main_pktdma 0xc603 15>,
+		       <&main_pktdma 0xc604 15>,
+		       <&main_pktdma 0xc605 15>,
+		       <&main_pktdma 0xc606 15>,
+		       <&main_pktdma 0xc607 15>,
+		       <&main_pktdma 0x4600 15>;
+		dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6",
+			    "tx7", "rx";
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cpsw_port1: port@1 {
+				reg = <1>;
+				ti,mac-only;
+				label = "port1";
+				phys = <&phy_gmii_sel 1>;
+				mac-address = [00 00 00 00 00 00];
+				ti,syscon-efuse = <&cpsw_efuse 0x00>;
+			};
+
+			cpsw_port2: port@2 {
+				reg = <2>;
+				ti,mac-only;
+				label = "port2";
+				phys = <&phy_gmii_sel 2>;
+				mac-address = [00 00 00 00 00 00];
+			};
+		};
+
+		cpsw3g_mdio: mdio@f00 {
+			compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+			reg = <0x00 0xf00 0x00 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&k3_clks 13 0>;
+			clock-names = "fck";
+			bus_freq = <1000000>;
+			status = "disabled";
+		};
+
+		cpts@3d000 {
+			compatible = "ti,j721e-cpts";
+			reg = <0x00 0x3d000 0x00 0x400>;
+			clocks = <&k3_clks 13 3>;
+			clock-names = "cpts";
+			interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cpts";
+			ti,cpts-ext-ts-inputs = <4>;
+			ti,cpts-periodic-outputs = <2>;
+		};
+	};
+
+	hwspinlock: spinlock@2a000000 {
+		compatible = "ti,am64-hwspinlock";
+		reg = <0x00 0x2a000000 0x00 0x1000>;
+		#hwlock-cells = <1>;
+	};
+
+	mailbox0_cluster0: mailbox@29000000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29000000 0x00 0x200>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	mailbox0_cluster1: mailbox@29010000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29010000 0x00 0x200>;
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	mailbox0_cluster2: mailbox@29020000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29020000 0x00 0x200>;
+		interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	mailbox0_cluster3: mailbox@29030000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29030000 0x00 0x200>;
+		interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	ecap0: pwm@23100000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23100000 0x00 0x100>;
+		power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 51 0>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	ecap1: pwm@23110000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23110000 0x00 0x100>;
+		power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 52 0>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	ecap2: pwm@23120000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23120000 0x00 0x100>;
+		power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 53 0>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	main_mcan0: can@20701000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x20701000 0x00 0x200>,
+		      <0x00 0x20708000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 98 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 98 6>, <&k3_clks 98 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+		status = "disabled";
+	};
+
+	main_mcan1: can@20711000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x20711000 0x00 0x200>,
+		      <0x00 0x20718000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 99 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 99 6>, <&k3_clks 99 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+		status = "disabled";
+	};
+
+	main_rti0: watchdog@e000000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x0e000000 0x00 0x100>;
+		clocks = <&k3_clks 125 0>;
+		power-domains = <&k3_pds 125 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 125 0>;
+		assigned-clock-parents = <&k3_clks 125 2>;
+	};
+
+	main_rti1: watchdog@e010000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x0e010000 0x00 0x100>;
+		clocks = <&k3_clks 126 0>;
+		power-domains = <&k3_pds 126 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 126 0>;
+		assigned-clock-parents = <&k3_clks 126 2>;
+	};
+
+	main_rti2: watchdog@e020000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x0e020000 0x00 0x100>;
+		clocks = <&k3_clks 127 0>;
+		power-domains = <&k3_pds 127 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 127 0>;
+		assigned-clock-parents = <&k3_clks 127 2>;
+	};
+
+	main_rti3: watchdog@e030000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x0e030000 0x00 0x100>;
+		clocks = <&k3_clks 128 0>;
+		power-domains = <&k3_pds 128 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 128 0>;
+		assigned-clock-parents = <&k3_clks 128 2>;
+	};
+
+	main_rti15: watchdog@e0f0000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x0e0f0000 0x00 0x100>;
+		clocks = <&k3_clks 130 0>;
+		power-domains = <&k3_pds 130 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 130 0>;
+		assigned-clock-parents = <&k3_clks 130 2>;
+	};
+
+	epwm0: pwm@23000000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23000000 0x00 0x100>;
+		power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	epwm1: pwm@23010000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23010000 0x00 0x100>;
+		power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	epwm2: pwm@23020000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23020000 0x00 0x100>;
+		power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	mcasp0: audio-controller@2b00000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b00000 0x00 0x2000>,
+		      <0x00 0x02b08000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 190 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 190 0>;
+		assigned-clock-parents = <&k3_clks 190 2>;
+		power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
+
+	mcasp1: audio-controller@2b10000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b10000 0x00 0x2000>,
+		      <0x00 0x02b18000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 191 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 191 0>;
+		assigned-clock-parents = <&k3_clks 191 2>;
+		power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
+
+	mcasp2: audio-controller@2b20000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b20000 0x00 0x2000>,
+		      <0x00 0x02b28000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 192 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 192 0>;
+		assigned-clock-parents = <&k3_clks 192 2>;
+		power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi
index 27ca1c9c6d135..c4b0b91d70cf3 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi
@@ -11,5 +11,195 @@  mcu_pmx0: pinctrl@4084000 {
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
 		pinctrl-single,function-mask = <0xffffffff>;
+		bootph-all;
+	};
+
+	mcu_esm: esm@4100000 {
+		compatible = "ti,j721e-esm";
+		reg = <0x00 0x4100000 0x00 0x1000>;
+		ti,esm-pins = <0>, <1>, <2>, <85>;
+		status = "reserved";
+		bootph-pre-ram;
+	};
+
+	/*
+	 * The MCU domain timer interrupts are routed only to the ESM module,
+	 * and not currently available for Linux. The MCU domain timers are
+	 * of limited use without interrupts, and likely reserved by the ESM.
+	 */
+	mcu_timer0: timer@4800000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4800000 0x00 0x400>;
+		clocks = <&k3_clks 35 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer1: timer@4810000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4810000 0x00 0x400>;
+		clocks = <&k3_clks 48 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer2: timer@4820000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4820000 0x00 0x400>;
+		clocks = <&k3_clks 49 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer3: timer@4830000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4830000 0x00 0x400>;
+		clocks = <&k3_clks 50 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_uart0: serial@4a00000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x04a00000 0x00 0x100>;
+		interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 149 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	mcu_i2c0: i2c@4900000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x04900000 0x00 0x100>;
+		interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 106 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	mcu_spi0: spi@4b00000 {
+		compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+		reg = <0x00 0x04b00000 0x00 0x400>;
+		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 147 0>;
+		status = "disabled";
+	};
+
+	mcu_spi1: spi@4b10000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x04b10000 0x00 0x400>;
+		interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 148 0>;
+		status = "disabled";
+	};
+
+	mcu_gpio_intr: interrupt-controller@4210000 {
+		compatible = "ti,sci-intr";
+		reg = <0x00 0x04210000 0x00 0x200>;
+		ti,intr-trigger-type = <1>;
+		interrupt-controller;
+		interrupt-parent = <&gic500>;
+		#interrupt-cells = <1>;
+		ti,sci = <&dmsc>;
+		ti,sci-dev-id = <5>;
+		ti,interrupt-ranges = <0 104 4>;
+	};
+
+	mcu_gpio0: gpio@4201000 {
+		compatible = "ti,am64-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x4201000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&mcu_gpio_intr>;
+		interrupts = <30>, <31>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <24>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 79 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 79 0>;
+		clock-names = "gpio";
+	};
+
+	mcu_rti0: watchdog@4880000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x04880000 0x00 0x100>;
+		clocks = <&k3_clks 131 0>;
+		power-domains = <&k3_pds 131 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 131 0>;
+		assigned-clock-parents = <&k3_clks 131 2>;
+		/* Tightly coupled to M4F */
+		status = "reserved";
+	};
+
+	mcu_mcan0: can@4e08000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x4e08000 0x00 0x200>,
+		      <0x00 0x4e00000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 188 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 188 6>, <&k3_clks 188 1>;
+		clock-names = "hclk", "cclk";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		status = "disabled";
+	};
+
+	mcu_mcan1: can@4e18000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x4e18000 0x00 0x200>,
+		      <0x00 0x4e10000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 189 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 189 6>, <&k3_clks 189 1>;
+		clock-names = "hclk", "cclk";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		status = "disabled";
+	};
+
+	mcu_r5fss0: r5fss@79000000 {
+		compatible = "ti,am62-r5fss";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x79000000 0x00 0x79000000 0x8000>,
+			 <0x79020000 0x00 0x79020000 0x8000>;
+		power-domains = <&k3_pds 7 TI_SCI_PD_EXCLUSIVE>;
+		mcu_r5fss0_core0: r5f@79000000 {
+			compatible = "ti,am62-r5f";
+			reg = <0x79000000 0x00008000>,
+			      <0x79020000 0x00008000>;
+			reg-names = "atcm", "btcm";
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <9>;
+			ti,sci-proc-ids = <0x03 0xff>;
+			resets = <&k3_reset 9 1>;
+			firmware-name = "am62p-mcu-r5f0_0-fw";
+			ti,atcm-enable = <0>;
+			ti,btcm-enable = <1>;
+			ti,loczrama = <0>;
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi
new file mode 100644
index 0000000000000..85ce545633ea5
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi
@@ -0,0 +1,47 @@ 
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/thermal/thermal.h>
+
+thermal_zones: thermal-zones {
+	main0_thermal: main0-thermal {
+		polling-delay-passive = <250>;	/* milliSeconds */
+		polling-delay = <500>;		/* milliSeconds */
+		thermal-sensors = <&wkup_vtm0 0>;
+
+		trips {
+			main0_crit: main0-crit {
+				temperature = <125000>;	/* milliCelsius */
+				hysteresis = <2000>;	/* milliCelsius */
+				type = "critical";
+			};
+		};
+	};
+
+	main1_thermal: main1-thermal {
+		polling-delay-passive = <250>;	/* milliSeconds */
+		polling-delay = <500>;		/* milliSeconds */
+		thermal-sensors = <&wkup_vtm0 1>;
+
+		trips {
+			main1_crit: main1-crit {
+				temperature = <125000>;	/* milliCelsius */
+				hysteresis = <2000>;	/* milliCelsius */
+				type = "critical";
+			};
+		};
+	};
+
+	main2_thermal: main2-thermal {
+	       polling-delay-passive = <250>;	/* milliSeconds */
+	       polling-delay = <500>;		/* milliSeconds */
+	       thermal-sensors = <&wkup_vtm0 2>;
+
+		trips {
+			main2_crit: main2-crit {
+				temperature = <125000>;	/* milliCelsius */
+				hysteresis = <2000>;	/* milliCelsius */
+				type = "critical";
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
index aaf4b793b58e7..e37f19f7e58ea 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
@@ -6,17 +6,35 @@ 
 
 &cbass_wakeup {
 	wkup_conf: bus@43000000 {
-		bootph-all;
 		compatible = "simple-bus";
 		reg = <0x00 0x43000000 0x00 0x20000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00 0x00 0x43000000 0x20000>;
+		bootph-all;
 
 		chipid: chipid@14 {
-			bootph-all;
 			compatible = "ti,am654-chipid";
 			reg = <0x14 0x4>;
+			bootph-all;
+		};
+
+		cpsw_efuse: syscon@200 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x200 0x4>;
+			bootph-all;
+		};
+
+		usb0_phy_pll_refclk: syscon@4008 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x4008 0x10>;
+			bootph-all;
+		};
+
+		usb1_phy_pll_refclk: syscon@4018 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x4018 0x10>;
+			bootph-all;
 		};
 	};
 
@@ -29,4 +47,69 @@  wkup_uart0: serial@2b300000 {
 		clock-names = "fclk";
 		status = "disabled";
 	};
+
+	wkup_i2c0: i2c@2b200000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x2b200000 0x00 0x100>;
+		interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 107 4>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	wkup_rtc0: rtc@2b1f0000 {
+		compatible = "ti,am62-rtc";
+		reg = <0x00 0x2b1f0000 0x00 0x100>;
+		interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 117 6> , <&k3_clks 117 0>;
+		clock-names = "vbus", "osc32k";
+		power-domains = <&k3_pds 117 TI_SCI_PD_EXCLUSIVE>;
+		wakeup-source;
+	};
+
+	wkup_rti0: watchdog@2b000000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x2b000000 0x00 0x100>;
+		clocks = <&k3_clks 132 0>;
+		power-domains = <&k3_pds 132 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 132 0>;
+		assigned-clock-parents = <&k3_clks 132 2>;
+		/* Used by DM firmware */
+		status = "reserved";
+	};
+
+	wkup_vtm0: temperature-sensor@b00000 {
+		compatible = "ti,j7200-vtm";
+		reg = <0x00 0xb00000 0x00 0x400>,
+		      <0x00 0xb01000 0x00 0x400>;
+		power-domains = <&k3_pds 95 TI_SCI_PD_EXCLUSIVE>;
+		#thermal-sensor-cells = <1>;
+	};
+
+	wkup_r5fss0: r5fss@78000000 {
+		compatible = "ti,am62-r5fss";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x78000000 0x00 0x78000000 0x8000>,
+			 <0x78100000 0x00 0x78100000 0x8000>;
+		power-domains = <&k3_pds 119 TI_SCI_PD_EXCLUSIVE>;
+
+		wkup_r5fss0_core0: r5f@78000000 {
+			compatible = "ti,am62-r5f";
+			reg = <0x78000000 0x00008000>,
+			      <0x78100000 0x00008000>;
+			reg-names = "atcm", "btcm";
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <121>;
+			ti,sci-proc-ids = <0x01 0xff>;
+			resets = <&k3_reset 121 1>;
+			firmware-name = "am62-wkup-r5f0_0-fw";
+			ti,atcm-enable = <1>;
+			ti,btcm-enable = <1>;
+			ti,loczrama = <1>;
+		};
+	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am62p.dtsi b/arch/arm64/boot/dts/ti/k3-am62p.dtsi
index 294ab73ec98b7..84ffe7b9dcaf3 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p.dtsi
@@ -45,10 +45,10 @@  pmu: pmu {
 	};
 
 	cbass_main: bus@f0000 {
-		bootph-all;
 		compatible = "simple-bus";
 		#address-cells = <2>;
 		#size-cells = <2>;
+		bootph-all;
 
 		ranges = <0x00 0x000f0000 0x00 0x000f0000 0x00 0x00030000>, /* Main MMRs */
 			 <0x00 0x00420000 0x00 0x00420000 0x00 0x00001000>, /* ESM0 */
@@ -100,10 +100,10 @@  cbass_mcu: bus@4000000 {
 				 <0x00 0x79020000 0x00 0x79020000 0x00 0x00008000>, /* MCU R5 BTCM */
 				 <0x00 0x79100000 0x00 0x79100000 0x00 0x00040000>, /* MCU IRAM0 */
 				 <0x00 0x79140000 0x00 0x79140000 0x00 0x00040000>; /* MCU IRAM1 */
+			bootph-all;
 		};
 
 		cbass_wakeup: bus@b00000 {
-			bootph-all;
 			compatible = "simple-bus";
 			#address-cells = <2>;
 			#size-cells = <2>;
@@ -112,8 +112,11 @@  cbass_wakeup: bus@b00000 {
 				 <0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>, /* WKUP CTRL MMR */
 				 <0x00 0x78000000 0x00 0x78000000 0x00 0x00008000>, /* DM R5 ATCM*/
 				 <0x00 0x78100000 0x00 0x78100000 0x00 0x00008000>; /* DM R5 BTCM*/
+			bootph-all;
 		};
 	};
+
+	#include "k3-am62p-thermal.dtsi"
 };
 
 /* Now include peripherals for each bus segment */