@@ -5,4 +5,4 @@
obj-$(CONFIG_QCOM_IPQ4019_ESS) += ipqess.o
-ipqess-objs := ipqess_port.o ipqess_switch.o ipqess_edma.o ipqess_ethtool.o ipqess_notifiers.o
+ipqess-objs := ipqess_port.o ipqess_switch.o ipqess_edma.o ipqess_ethtool.o ipqess_notifiers.o ipqess_calib.o
new file mode 100644
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Calibration procedure for the IPQ4019 PSGMII link
+ *
+ * Copyright (C) 2009 Felix Fietkau <nbd@nbd.name>
+ * Copyright (C) 2011-2012, 2020-2021 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (c) 2015, 2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2016 John Crispin <john@phrozen.org>
+ * Copyright (c) 2022 Robert Marko <robert.marko@sartura.hr>
+ * Copyright (c) 2023 Romain Gantois <romain.gantois@bootlin.com>
+ */
+
+#include <linux/dsa/qca8k.h>
+#include <linux/phylink.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+#include <linux/regmap.h>
+
+#include "ipqess_port.h"
+#include "ipqess_switch.h"
+
+/* Nonstandard MII registers for the psgmii
+ * device on the IPQ4019 MDIO bus.
+ */
+
+#define PSGMII_RSTCTRL 0x0 /* Reset control register */
+#define PSGMII_RSTCTRL_RST BIT(6)
+#define PSGMII_RSTCTRL_RX20 BIT(2) /* Fix/release RX 20 bit */
+
+#define PSGMII_CDRCTRL 0x1a /* Clock and data recovery control register */
+#define PSGMII_CDRCTRL_RELEASE BIT(12)
+
+/* Retry policy */
+
+#define PSGMII_CALIB_RETRIES 50
+#define PSGMII_CALIB_RETRIES_BURST 5
+#define PSGMII_CALIB_RETRY_DELAY 100
+
+/* PSGMII PHY specific definitions */
+#define PSGMII_VCO_CALIB_INTERVAL 1000000
+#define PSGMII_VCO_CALIB_TIMEOUT 10000
+
+static void ipqess_port_unprep_test(struct ipqess_port *port)
+{
+ struct qca8k_priv *priv = port->sw->priv;
+ /* disable loopback on switch port */
+ qca8k_clear_bits(priv, QCA8K_PORT_LOOKUP_CTRL(port->index),
+ QCA8K_PORT_LOOKUP_LOOPBACK_EN);
+
+ qca8k_write(priv, QCA8K_REG_PORT_STATUS(port->index), 0);
+ qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port->index),
+ QCA8K_PORT_LOOKUP_STATE_DISABLED,
+ QCA8K_PORT_LOOKUP_STATE_DISABLED);
+}
+
+static void ipqess_port_prep_test(struct ipqess_port *port)
+{
+ struct qca8k_priv *priv = port->sw->priv;
+
+ qca8k_write(priv, QCA8K_REG_PORT_STATUS(port->index),
+ QCA8K_PORT_STATUS_SPEED_1000
+ | QCA8K_PORT_STATUS_TXMAC
+ | QCA8K_PORT_STATUS_RXMAC
+ | QCA8K_PORT_STATUS_DUPLEX);
+
+ qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port->index),
+ QCA8K_PORT_LOOKUP_STATE_FORWARD,
+ QCA8K_PORT_LOOKUP_STATE_FORWARD);
+
+ /* put switch port in loopback */
+ qca8k_set_bits(priv, QCA8K_PORT_LOOKUP_CTRL(port->index),
+ QCA8K_PORT_LOOKUP_LOOPBACK_EN);
+}
+
+static int psgmii_vco_calibrate(struct ipqess_port *port)
+{
+ struct ipqess_switch *sw = port->sw;
+ struct qca8k_priv *priv = sw->priv;
+ struct ipqess_port *other_port;
+ int val, ret, i;
+
+ ret = phy_start_calibration(port->netdev->phydev);
+ if (ret) {
+ dev_err(priv->dev,
+ "PHY VCO calibration PLL not ready\n");
+ return ret;
+ }
+
+ /* Start PSGMIIPHY VCO PLL calibration */
+ ret = regmap_set_bits(priv->psgmii,
+ PSGMIIPHY_VCO_CALIBRATION_CONTROL_REGISTER_1,
+ PSGMIIPHY_REG_PLL_VCO_CALIB_RESTART);
+
+ /* Poll for PSGMIIPHY PLL calibration finish - Dakota(IPQ40xx) */
+ ret = regmap_read_poll_timeout(priv->psgmii,
+ PSGMIIPHY_VCO_CALIBRATION_CONTROL_REGISTER_2,
+ val,
+ val & PSGMIIPHY_REG_PLL_VCO_CALIB_READY,
+ PSGMII_VCO_CALIB_INTERVAL,
+ PSGMII_VCO_CALIB_TIMEOUT);
+ if (ret) {
+ dev_err(priv->dev,
+ "IPQ PSGMIIPHY VCO calibration PLL not ready\n");
+ return ret;
+ }
+
+ /* Prepare all switch ports, in case we're dealing with a multiport PHY */
+ for (i = 0; i < IPQESS_SWITCH_MAX_PORTS; i++) {
+ other_port = sw->port_list[i];
+ if (!other_port)
+ continue;
+ ipqess_port_prep_test(other_port);
+ }
+
+ ret = phy_stop_calibration(port->netdev->phydev);
+
+ for (i = 0; i < IPQESS_SWITCH_MAX_PORTS; i++) {
+ other_port = sw->port_list[i];
+ if (!other_port)
+ continue;
+ ipqess_port_unprep_test(other_port);
+ }
+
+ qca8k_fdb_flush(priv);
+
+ return ret;
+}
+
+int psgmii_calibrate_and_test(struct ipqess_port *port)
+{
+ int ret, attempt;
+
+ for (attempt = 0; attempt <= PSGMII_CALIB_RETRIES; attempt++) {
+ ret = psgmii_vco_calibrate(port);
+ if (!ret) {
+ netdev_dbg(port->netdev,
+ "PSGMII link stabilized after %d attempts\n",
+ attempt + 1);
+ return 0;
+ }
+
+ /* On tested hardware, the link often stabilizes in 4 or 5 retries.
+ * If it still isn't stable, we wait a bit, then try another set
+ * of calibration attempts.
+ */
+ netdev_dbg(port->netdev, "PSGMII link is unstable! Retrying... %d/QCA8K_PSGMII_CALIB_RETRIES\n",
+ attempt + 1);
+ if (attempt % PSGMII_CALIB_RETRIES_BURST == 0)
+ schedule_timeout_interruptible(msecs_to_jiffies(PSGMII_CALIB_RETRY_DELAY));
+ else
+ schedule();
+ }
+
+ netdev_err(port->netdev, "PSGMII work is unstable! Repeated recalibration attempts did not help!\n");
+ return -EFAULT;
+}
@@ -1218,6 +1218,26 @@ int ipqess_port_check_8021q_upper(struct net_device *netdev,
/* phylink ops */
+static int
+ipqess_psgmii_configure(struct ipqess_port *port)
+{
+ int ret = 0;
+
+ /* For this multi-port PHY, we only need one calibration run,
+ * don't rerun it for other ports
+ */
+ if (!atomic_cmpxchg(&port->sw->priv->psgmii_calibrated, 0, 1)) {
+ psgmii_calibrate_and_test(port);
+
+ ret = regmap_clear_bits(port->sw->priv->psgmii, PSGMIIPHY_MODE_CONTROL,
+ PSGMIIPHY_MODE_ATHR_CSCO_MODE_25M);
+ ret = regmap_write(port->sw->priv->psgmii, PSGMIIPHY_TX_CONTROL,
+ PSGMIIPHY_TX_CONTROL_MAGIC_VALUE);
+ }
+
+ return ret;
+}
+
static void
ipqess_phylink_mac_config(struct phylink_config *config,
unsigned int mode,
@@ -1233,12 +1253,22 @@ ipqess_phylink_mac_config(struct phylink_config *config,
case 1:
case 2:
case 3:
+ if (state->interface == PHY_INTERFACE_MODE_PSGMII)
+ if (ipqess_psgmii_configure(port))
+ dev_err(priv->dev,
+ "PSGMII configuration failed!\n");
+ return;
case 4:
case 5:
if (phy_interface_mode_is_rgmii(state->interface))
regmap_set_bits(priv->regmap,
QCA8K_IPQ4019_REG_RGMII_CTRL,
QCA8K_IPQ4019_RGMII_CTRL_CLK);
+
+ if (state->interface == PHY_INTERFACE_MODE_PSGMII)
+ if (ipqess_psgmii_configure(port))
+ dev_err(priv->dev,
+ "PSGMII configuration failed!\n");
return;
default:
dev_err(priv->dev, "%s: unsupported port: %i\n", __func__,
@@ -95,4 +95,8 @@ int ipqess_port_obj_del(struct net_device *netdev, const void *ctx,
bool ipqess_port_offloads_bridge_port(struct ipqess_port *port,
const struct net_device *netdev);
+
+/* Defined in ipqess_calib.c */
+int psgmii_calibrate_and_test(struct ipqess_port *port);
+
#endif
@@ -496,6 +496,7 @@ struct qca8k_priv {
/* IPQ4019 specific */
struct regmap *psgmii;
+ atomic_t psgmii_calibrated;
};
struct qca8k_mib_desc {
The IPQ4019 Ethernet Switch Subsystem uses a PSGMII link to communicate with a QCA8075 5-port PHY. This 1G link requires calibration before it can be used reliably. This commit introduces a calibration procedure followed by thourough testing of the link between each switch port and its corresponding PHY port. Signed-off-by: Romain Gantois <romain.gantois@bootlin.com> --- drivers/net/ethernet/qualcomm/ipqess/Makefile | 2 +- .../ethernet/qualcomm/ipqess/ipqess_calib.c | 156 ++++++++++++++++++ .../ethernet/qualcomm/ipqess/ipqess_port.c | 30 ++++ .../ethernet/qualcomm/ipqess/ipqess_port.h | 4 + include/linux/dsa/qca8k.h | 1 + 5 files changed, 192 insertions(+), 1 deletion(-) create mode 100644 drivers/net/ethernet/qualcomm/ipqess/ipqess_calib.c