| Message ID | 20231207-drop-11mpcore-v2-1-560b396f3bf5@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v2] ARM: Delete ARM11MPCore (ARM11 ARMv6K SMP) support | expand |
On Thu, Dec 07, 2023 at 02:33:35PM +0100, Linus Walleij wrote: > This ARM11 SMP configuration was one of the first SMP configurations > the ARM kernel supported, but it has the downside of odd DMA handling, > odd cache tagging, and often (as of recent) completely broken cache > handling on the ARM RealView PB11MPCore test chips. To boot the > platform it was necessary to completely disable the cache. > When it comes to the EB 11MPCore it is unclear if this ever worked. > > These reference designs are now the only ARMv6K SMP platforms. > > As only reference designs of purely academic interest remain, and > since the special-cased DMA and PMU code is hard to maintain and > doesn't really work, it is not really worth our time. > > Delete the ARM11MPCore support along with: > > - The special DMA quirk CONFIG_DMA_CACHE_RWFO that is only used > on ARMv6K SMP, and we are the last ARMV6K system leaving the > building and the cache handling is awkward, so good-bye. > > - The special PMU handling that was only used by ARM11MPCore. > > The following is left behind: > > - TIMER_OF_DECLARE(arm_twd_11mp, "arm,arm11mp-twd-timer", ...) > in arch/arm/kernel/smp_twd.c, this is still in use by Marvell MMP3 > arch/arm/boot/dts/marvell/mmp3.dtsi > > - IRQCHIP_DECLARE(arm11mp_gic, "arm,arm11mp-gic", ...) > in drivers/irqchip/irq-gic.c, this is still in use by Marvell MMP3 > arch/arm/boot/dts/marvell/mmp3.dtsi > > - A compatible for the arm11mpcore SCU, since this was mistakedly > used for the Cortex-A9 version of RealView EB. > > These are unfortunate but will need to be kept around for > compatibility. New Marvell-specific compatibles should however probably > be added. I remember seeing a decade ago some evaluation boards with ARM11MPCore but that's as far as I have ever come close to this platform. For what is worth: Acked-by: Liviu Dudau <liviu.dudau@arm.com> Best regards, Liviu > > Acked-by: Mark Rutland <mark.rutland@arm.com> > Reviewed-by: Arnd Bergmann <arnd@arndb.de> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> > --- > Changes in v2: > - Keep the PB11MPCore SCU compatible for a bit (until we delete these > RealView EB device trees). > - Please apply this to the SoC tree once there is consensus. > - Link to v1: https://lore.kernel.org/r/20231204-drop-11mpcore-v1-1-f96cd3938cf1@linaro.org > --- > arch/arm/kernel/perf_event_v6.c | 34 ------------------------------ > arch/arm/mach-versatile/Kconfig | 17 --------------- > arch/arm/mach-versatile/platsmp-realview.c | 6 +++++- > arch/arm/mach-versatile/realview.c | 1 - > arch/arm/mm/Kconfig | 18 ---------------- > arch/arm/mm/cache-v6.S | 31 --------------------------- > 6 files changed, 5 insertions(+), 102 deletions(-) > > diff --git a/arch/arm/kernel/perf_event_v6.c b/arch/arm/kernel/perf_event_v6.c > index 1ae99deeec54..3115077f6abc 100644 > --- a/arch/arm/kernel/perf_event_v6.c > +++ b/arch/arm/kernel/perf_event_v6.c > @@ -525,40 +525,7 @@ static int armv6_1176_pmu_init(struct arm_pmu *cpu_pmu) > return 0; > } > > -/* > - * ARMv6mpcore is almost identical to single core ARMv6 with the exception > - * that some of the events have different enumerations and that there is no > - * *hack* to stop the programmable counters. To stop the counters we simply > - * disable the interrupt reporting and update the event. When unthrottling we > - * reset the period and enable the interrupt reporting. > - */ > - > -static int armv6mpcore_map_event(struct perf_event *event) > -{ > - return armpmu_map_event(event, &armv6mpcore_perf_map, > - &armv6mpcore_perf_cache_map, 0xFF); > -} > - > -static int armv6mpcore_pmu_init(struct arm_pmu *cpu_pmu) > -{ > - cpu_pmu->name = "armv6_11mpcore"; > - cpu_pmu->handle_irq = armv6pmu_handle_irq; > - cpu_pmu->enable = armv6pmu_enable_event; > - cpu_pmu->disable = armv6mpcore_pmu_disable_event; > - cpu_pmu->read_counter = armv6pmu_read_counter; > - cpu_pmu->write_counter = armv6pmu_write_counter; > - cpu_pmu->get_event_idx = armv6pmu_get_event_idx; > - cpu_pmu->clear_event_idx = armv6pmu_clear_event_idx; > - cpu_pmu->start = armv6pmu_start; > - cpu_pmu->stop = armv6pmu_stop; > - cpu_pmu->map_event = armv6mpcore_map_event; > - cpu_pmu->num_events = 3; > - > - return 0; > -} > - > static const struct of_device_id armv6_pmu_of_device_ids[] = { > - {.compatible = "arm,arm11mpcore-pmu", .data = armv6mpcore_pmu_init}, > {.compatible = "arm,arm1176-pmu", .data = armv6_1176_pmu_init}, > {.compatible = "arm,arm1136-pmu", .data = armv6_1136_pmu_init}, > { /* sentinel value */ } > @@ -568,7 +535,6 @@ static const struct pmu_probe_info armv6_pmu_probe_table[] = { > ARM_PMU_PROBE(ARM_CPU_PART_ARM1136, armv6_1136_pmu_init), > ARM_PMU_PROBE(ARM_CPU_PART_ARM1156, armv6_1156_pmu_init), > ARM_PMU_PROBE(ARM_CPU_PART_ARM1176, armv6_1176_pmu_init), > - ARM_PMU_PROBE(ARM_CPU_PART_ARM11MPCORE, armv6mpcore_pmu_init), > { /* sentinel value */ } > }; > > diff --git a/arch/arm/mach-versatile/Kconfig b/arch/arm/mach-versatile/Kconfig > index b1519b4dc03a..e029270c2687 100644 > --- a/arch/arm/mach-versatile/Kconfig > +++ b/arch/arm/mach-versatile/Kconfig > @@ -201,23 +201,6 @@ config REALVIEW_EB_A9MP > Enable support for the Cortex-A9MPCore tile fitted to the > Realview(R) Emulation Baseboard platform. > > -config REALVIEW_EB_ARM11MP > - bool "Support ARM11MPCore Tile" > - depends on MACH_REALVIEW_EB && ARCH_MULTI_V6 > - select HAVE_SMP > - help > - Enable support for the ARM11MPCore tile fitted to the Realview(R) > - Emulation Baseboard platform. > - > -config MACH_REALVIEW_PB11MP > - bool "Support RealView(R) Platform Baseboard for ARM11MPCore" > - depends on ARCH_MULTI_V6 > - select HAVE_SMP > - help > - Include support for the ARM(R) RealView(R) Platform Baseboard for > - the ARM11MPCore. This platform has an on-board ARM11MPCore and has > - support for PCI-E and Compact Flash. > - > # ARMv6 CPU without K extensions, but does have the new exclusive ops > config MACH_REALVIEW_PB1176 > bool "Support RealView(R) Platform Baseboard for ARM1176JZF-S" > diff --git a/arch/arm/mach-versatile/platsmp-realview.c b/arch/arm/mach-versatile/platsmp-realview.c > index 5d363385c801..6965a1de727b 100644 > --- a/arch/arm/mach-versatile/platsmp-realview.c > +++ b/arch/arm/mach-versatile/platsmp-realview.c > @@ -18,6 +18,11 @@ > #define REALVIEW_SYS_FLAGSSET_OFFSET 0x30 > > static const struct of_device_id realview_scu_match[] = { > + /* > + * The ARM11MP SCU compatible is only provided as fallback for > + * old RealView EB Cortex-A9 device trees that were using this > + * compatible by mistake. > + */ > { .compatible = "arm,arm11mp-scu", }, > { .compatible = "arm,cortex-a9-scu", }, > { .compatible = "arm,cortex-a5-scu", }, > @@ -27,7 +32,6 @@ static const struct of_device_id realview_scu_match[] = { > static const struct of_device_id realview_syscon_match[] = { > { .compatible = "arm,core-module-integrator", }, > { .compatible = "arm,realview-eb-syscon", }, > - { .compatible = "arm,realview-pb11mp-syscon", }, > { .compatible = "arm,realview-pbx-syscon", }, > { }, > }; > diff --git a/arch/arm/mach-versatile/realview.c b/arch/arm/mach-versatile/realview.c > index a3933e2373d5..36a6f6bc4fdd 100644 > --- a/arch/arm/mach-versatile/realview.c > +++ b/arch/arm/mach-versatile/realview.c > @@ -9,7 +9,6 @@ > static const char *const realview_dt_platform_compat[] __initconst = { > "arm,realview-eb", > "arm,realview-pb1176", > - "arm,realview-pb11mp", > "arm,realview-pba8", > "arm,realview-pbx", > NULL, > diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig > index c164cde50243..2b6f50dd5478 100644 > --- a/arch/arm/mm/Kconfig > +++ b/arch/arm/mm/Kconfig > @@ -937,24 +937,6 @@ config VDSO > You must have glibc 2.22 or later for programs to seamlessly > take advantage of this. > > -config DMA_CACHE_RWFO > - bool "Enable read/write for ownership DMA cache maintenance" > - depends on CPU_V6K && SMP > - default y > - help > - The Snoop Control Unit on ARM11MPCore does not detect the > - cache maintenance operations and the dma_{map,unmap}_area() > - functions may leave stale cache entries on other CPUs. By > - enabling this option, Read or Write For Ownership in the ARMv6 > - DMA cache maintenance functions is performed. These LDR/STR > - instructions change the cache line state to shared or modified > - so that the cache operation has the desired effect. > - > - Note that the workaround is only valid on processors that do > - not perform speculative loads into the D-cache. For such > - processors, if cache maintenance operations are not broadcast > - in hardware, other workarounds are needed (e.g. cache > - maintenance broadcasting in software via FIQ). > > config OUTER_CACHE > bool > diff --git a/arch/arm/mm/cache-v6.S b/arch/arm/mm/cache-v6.S > index 250c83bf7158..44211d8a296f 100644 > --- a/arch/arm/mm/cache-v6.S > +++ b/arch/arm/mm/cache-v6.S > @@ -201,10 +201,6 @@ ENTRY(v6_flush_kern_dcache_area) > * - end - virtual end address of region > */ > v6_dma_inv_range: > -#ifdef CONFIG_DMA_CACHE_RWFO > - ldrb r2, [r0] @ read for ownership > - strb r2, [r0] @ write for ownership > -#endif > tst r0, #D_CACHE_LINE_SIZE - 1 > bic r0, r0, #D_CACHE_LINE_SIZE - 1 > #ifdef HARVARD_CACHE > @@ -213,10 +209,6 @@ v6_dma_inv_range: > mcrne p15, 0, r0, c7, c11, 1 @ clean unified line > #endif > tst r1, #D_CACHE_LINE_SIZE - 1 > -#ifdef CONFIG_DMA_CACHE_RWFO > - ldrbne r2, [r1, #-1] @ read for ownership > - strbne r2, [r1, #-1] @ write for ownership > -#endif > bic r1, r1, #D_CACHE_LINE_SIZE - 1 > #ifdef HARVARD_CACHE > mcrne p15, 0, r1, c7, c14, 1 @ clean & invalidate D line > @@ -231,10 +223,6 @@ v6_dma_inv_range: > #endif > add r0, r0, #D_CACHE_LINE_SIZE > cmp r0, r1 > -#ifdef CONFIG_DMA_CACHE_RWFO > - ldrlo r2, [r0] @ read for ownership > - strlo r2, [r0] @ write for ownership > -#endif > blo 1b > mov r0, #0 > mcr p15, 0, r0, c7, c10, 4 @ drain write buffer > @@ -248,9 +236,6 @@ v6_dma_inv_range: > v6_dma_clean_range: > bic r0, r0, #D_CACHE_LINE_SIZE - 1 > 1: > -#ifdef CONFIG_DMA_CACHE_RWFO > - ldr r2, [r0] @ read for ownership > -#endif > #ifdef HARVARD_CACHE > mcr p15, 0, r0, c7, c10, 1 @ clean D line > #else > @@ -269,10 +254,6 @@ v6_dma_clean_range: > * - end - virtual end address of region > */ > ENTRY(v6_dma_flush_range) > -#ifdef CONFIG_DMA_CACHE_RWFO > - ldrb r2, [r0] @ read for ownership > - strb r2, [r0] @ write for ownership > -#endif > bic r0, r0, #D_CACHE_LINE_SIZE - 1 > 1: > #ifdef HARVARD_CACHE > @@ -282,10 +263,6 @@ ENTRY(v6_dma_flush_range) > #endif > add r0, r0, #D_CACHE_LINE_SIZE > cmp r0, r1 > -#ifdef CONFIG_DMA_CACHE_RWFO > - ldrblo r2, [r0] @ read for ownership > - strblo r2, [r0] @ write for ownership > -#endif > blo 1b > mov r0, #0 > mcr p15, 0, r0, c7, c10, 4 @ drain write buffer > @@ -301,13 +278,7 @@ ENTRY(v6_dma_map_area) > add r1, r1, r0 > teq r2, #DMA_FROM_DEVICE > beq v6_dma_inv_range > -#ifndef CONFIG_DMA_CACHE_RWFO > b v6_dma_clean_range > -#else > - teq r2, #DMA_TO_DEVICE > - beq v6_dma_clean_range > - b v6_dma_flush_range > -#endif > ENDPROC(v6_dma_map_area) > > /* > @@ -317,11 +288,9 @@ ENDPROC(v6_dma_map_area) > * - dir - DMA direction > */ > ENTRY(v6_dma_unmap_area) > -#ifndef CONFIG_DMA_CACHE_RWFO > add r1, r1, r0 > teq r2, #DMA_TO_DEVICE > bne v6_dma_inv_range > -#endif > ret lr > ENDPROC(v6_dma_unmap_area) > > > --- > base-commit: d570fe67df85c84be7cc33ca9e9568d9601b494f > change-id: 20231202-drop-11mpcore-d556cc5f7d99 > > Best regards, > -- > Linus Walleij <linus.walleij@linaro.org> >
diff --git a/arch/arm/kernel/perf_event_v6.c b/arch/arm/kernel/perf_event_v6.c index 1ae99deeec54..3115077f6abc 100644 --- a/arch/arm/kernel/perf_event_v6.c +++ b/arch/arm/kernel/perf_event_v6.c @@ -525,40 +525,7 @@ static int armv6_1176_pmu_init(struct arm_pmu *cpu_pmu) return 0; } -/* - * ARMv6mpcore is almost identical to single core ARMv6 with the exception - * that some of the events have different enumerations and that there is no - * *hack* to stop the programmable counters. To stop the counters we simply - * disable the interrupt reporting and update the event. When unthrottling we - * reset the period and enable the interrupt reporting. - */ - -static int armv6mpcore_map_event(struct perf_event *event) -{ - return armpmu_map_event(event, &armv6mpcore_perf_map, - &armv6mpcore_perf_cache_map, 0xFF); -} - -static int armv6mpcore_pmu_init(struct arm_pmu *cpu_pmu) -{ - cpu_pmu->name = "armv6_11mpcore"; - cpu_pmu->handle_irq = armv6pmu_handle_irq; - cpu_pmu->enable = armv6pmu_enable_event; - cpu_pmu->disable = armv6mpcore_pmu_disable_event; - cpu_pmu->read_counter = armv6pmu_read_counter; - cpu_pmu->write_counter = armv6pmu_write_counter; - cpu_pmu->get_event_idx = armv6pmu_get_event_idx; - cpu_pmu->clear_event_idx = armv6pmu_clear_event_idx; - cpu_pmu->start = armv6pmu_start; - cpu_pmu->stop = armv6pmu_stop; - cpu_pmu->map_event = armv6mpcore_map_event; - cpu_pmu->num_events = 3; - - return 0; -} - static const struct of_device_id armv6_pmu_of_device_ids[] = { - {.compatible = "arm,arm11mpcore-pmu", .data = armv6mpcore_pmu_init}, {.compatible = "arm,arm1176-pmu", .data = armv6_1176_pmu_init}, {.compatible = "arm,arm1136-pmu", .data = armv6_1136_pmu_init}, { /* sentinel value */ } @@ -568,7 +535,6 @@ static const struct pmu_probe_info armv6_pmu_probe_table[] = { ARM_PMU_PROBE(ARM_CPU_PART_ARM1136, armv6_1136_pmu_init), ARM_PMU_PROBE(ARM_CPU_PART_ARM1156, armv6_1156_pmu_init), ARM_PMU_PROBE(ARM_CPU_PART_ARM1176, armv6_1176_pmu_init), - ARM_PMU_PROBE(ARM_CPU_PART_ARM11MPCORE, armv6mpcore_pmu_init), { /* sentinel value */ } }; diff --git a/arch/arm/mach-versatile/Kconfig b/arch/arm/mach-versatile/Kconfig index b1519b4dc03a..e029270c2687 100644 --- a/arch/arm/mach-versatile/Kconfig +++ b/arch/arm/mach-versatile/Kconfig @@ -201,23 +201,6 @@ config REALVIEW_EB_A9MP Enable support for the Cortex-A9MPCore tile fitted to the Realview(R) Emulation Baseboard platform. -config REALVIEW_EB_ARM11MP - bool "Support ARM11MPCore Tile" - depends on MACH_REALVIEW_EB && ARCH_MULTI_V6 - select HAVE_SMP - help - Enable support for the ARM11MPCore tile fitted to the Realview(R) - Emulation Baseboard platform. - -config MACH_REALVIEW_PB11MP - bool "Support RealView(R) Platform Baseboard for ARM11MPCore" - depends on ARCH_MULTI_V6 - select HAVE_SMP - help - Include support for the ARM(R) RealView(R) Platform Baseboard for - the ARM11MPCore. This platform has an on-board ARM11MPCore and has - support for PCI-E and Compact Flash. - # ARMv6 CPU without K extensions, but does have the new exclusive ops config MACH_REALVIEW_PB1176 bool "Support RealView(R) Platform Baseboard for ARM1176JZF-S" diff --git a/arch/arm/mach-versatile/platsmp-realview.c b/arch/arm/mach-versatile/platsmp-realview.c index 5d363385c801..6965a1de727b 100644 --- a/arch/arm/mach-versatile/platsmp-realview.c +++ b/arch/arm/mach-versatile/platsmp-realview.c @@ -18,6 +18,11 @@ #define REALVIEW_SYS_FLAGSSET_OFFSET 0x30 static const struct of_device_id realview_scu_match[] = { + /* + * The ARM11MP SCU compatible is only provided as fallback for + * old RealView EB Cortex-A9 device trees that were using this + * compatible by mistake. + */ { .compatible = "arm,arm11mp-scu", }, { .compatible = "arm,cortex-a9-scu", }, { .compatible = "arm,cortex-a5-scu", }, @@ -27,7 +32,6 @@ static const struct of_device_id realview_scu_match[] = { static const struct of_device_id realview_syscon_match[] = { { .compatible = "arm,core-module-integrator", }, { .compatible = "arm,realview-eb-syscon", }, - { .compatible = "arm,realview-pb11mp-syscon", }, { .compatible = "arm,realview-pbx-syscon", }, { }, }; diff --git a/arch/arm/mach-versatile/realview.c b/arch/arm/mach-versatile/realview.c index a3933e2373d5..36a6f6bc4fdd 100644 --- a/arch/arm/mach-versatile/realview.c +++ b/arch/arm/mach-versatile/realview.c @@ -9,7 +9,6 @@ static const char *const realview_dt_platform_compat[] __initconst = { "arm,realview-eb", "arm,realview-pb1176", - "arm,realview-pb11mp", "arm,realview-pba8", "arm,realview-pbx", NULL, diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index c164cde50243..2b6f50dd5478 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -937,24 +937,6 @@ config VDSO You must have glibc 2.22 or later for programs to seamlessly take advantage of this. -config DMA_CACHE_RWFO - bool "Enable read/write for ownership DMA cache maintenance" - depends on CPU_V6K && SMP - default y - help - The Snoop Control Unit on ARM11MPCore does not detect the - cache maintenance operations and the dma_{map,unmap}_area() - functions may leave stale cache entries on other CPUs. By - enabling this option, Read or Write For Ownership in the ARMv6 - DMA cache maintenance functions is performed. These LDR/STR - instructions change the cache line state to shared or modified - so that the cache operation has the desired effect. - - Note that the workaround is only valid on processors that do - not perform speculative loads into the D-cache. For such - processors, if cache maintenance operations are not broadcast - in hardware, other workarounds are needed (e.g. cache - maintenance broadcasting in software via FIQ). config OUTER_CACHE bool diff --git a/arch/arm/mm/cache-v6.S b/arch/arm/mm/cache-v6.S index 250c83bf7158..44211d8a296f 100644 --- a/arch/arm/mm/cache-v6.S +++ b/arch/arm/mm/cache-v6.S @@ -201,10 +201,6 @@ ENTRY(v6_flush_kern_dcache_area) * - end - virtual end address of region */ v6_dma_inv_range: -#ifdef CONFIG_DMA_CACHE_RWFO - ldrb r2, [r0] @ read for ownership - strb r2, [r0] @ write for ownership -#endif tst r0, #D_CACHE_LINE_SIZE - 1 bic r0, r0, #D_CACHE_LINE_SIZE - 1 #ifdef HARVARD_CACHE @@ -213,10 +209,6 @@ v6_dma_inv_range: mcrne p15, 0, r0, c7, c11, 1 @ clean unified line #endif tst r1, #D_CACHE_LINE_SIZE - 1 -#ifdef CONFIG_DMA_CACHE_RWFO - ldrbne r2, [r1, #-1] @ read for ownership - strbne r2, [r1, #-1] @ write for ownership -#endif bic r1, r1, #D_CACHE_LINE_SIZE - 1 #ifdef HARVARD_CACHE mcrne p15, 0, r1, c7, c14, 1 @ clean & invalidate D line @@ -231,10 +223,6 @@ v6_dma_inv_range: #endif add r0, r0, #D_CACHE_LINE_SIZE cmp r0, r1 -#ifdef CONFIG_DMA_CACHE_RWFO - ldrlo r2, [r0] @ read for ownership - strlo r2, [r0] @ write for ownership -#endif blo 1b mov r0, #0 mcr p15, 0, r0, c7, c10, 4 @ drain write buffer @@ -248,9 +236,6 @@ v6_dma_inv_range: v6_dma_clean_range: bic r0, r0, #D_CACHE_LINE_SIZE - 1 1: -#ifdef CONFIG_DMA_CACHE_RWFO - ldr r2, [r0] @ read for ownership -#endif #ifdef HARVARD_CACHE mcr p15, 0, r0, c7, c10, 1 @ clean D line #else @@ -269,10 +254,6 @@ v6_dma_clean_range: * - end - virtual end address of region */ ENTRY(v6_dma_flush_range) -#ifdef CONFIG_DMA_CACHE_RWFO - ldrb r2, [r0] @ read for ownership - strb r2, [r0] @ write for ownership -#endif bic r0, r0, #D_CACHE_LINE_SIZE - 1 1: #ifdef HARVARD_CACHE @@ -282,10 +263,6 @@ ENTRY(v6_dma_flush_range) #endif add r0, r0, #D_CACHE_LINE_SIZE cmp r0, r1 -#ifdef CONFIG_DMA_CACHE_RWFO - ldrblo r2, [r0] @ read for ownership - strblo r2, [r0] @ write for ownership -#endif blo 1b mov r0, #0 mcr p15, 0, r0, c7, c10, 4 @ drain write buffer @@ -301,13 +278,7 @@ ENTRY(v6_dma_map_area) add r1, r1, r0 teq r2, #DMA_FROM_DEVICE beq v6_dma_inv_range -#ifndef CONFIG_DMA_CACHE_RWFO b v6_dma_clean_range -#else - teq r2, #DMA_TO_DEVICE - beq v6_dma_clean_range - b v6_dma_flush_range -#endif ENDPROC(v6_dma_map_area) /* @@ -317,11 +288,9 @@ ENDPROC(v6_dma_map_area) * - dir - DMA direction */ ENTRY(v6_dma_unmap_area) -#ifndef CONFIG_DMA_CACHE_RWFO add r1, r1, r0 teq r2, #DMA_TO_DEVICE bne v6_dma_inv_range -#endif ret lr ENDPROC(v6_dma_unmap_area)