@@ -22,7 +22,9 @@
#include <linux/of.h>
#include <linux/module.h>
#include <linux/pm_runtime.h>
-#include <linux/iopoll.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/delay.h>
#define CDNS_UART_TTY_NAME "ttyPS"
#define CDNS_UART_NAME "xuartps"
@@ -193,6 +195,10 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
* @clk_rate_change_nb: Notifier block for clock changes
* @quirks: Flags for RXBS support.
* @cts_override: Modem control state override
+ * @gpiod_rts: Pointer to the gpio descriptor
+ * @rs485_tx_started: RS485 tx state
+ * @timer: Timer for tx and rx
+ * @stop_tx_timer: Timer for stop tx
*/
struct cdns_uart {
struct uart_port *port;
@@ -203,10 +209,22 @@ struct cdns_uart {
struct notifier_block clk_rate_change_nb;
u32 quirks;
bool cts_override;
+ struct gpio_desc *gpiod_rts;
+ bool rs485_tx_started;
+ struct timer_list timer;
+ struct timer_list stop_tx_timer;
};
struct cdns_platform_data {
u32 quirks;
};
+
+struct serial_rs485 cdns_rs485_supported = {
+ .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+ SER_RS485_RTS_AFTER_SEND,
+ .delay_rts_before_send = 1,
+ .delay_rts_after_send = 1,
+};
+
#define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \
clk_rate_change_nb)
@@ -305,6 +323,55 @@ static void cdns_uart_handle_rx(void *dev_id, unsigned int isrstatus)
tty_flip_buffer_push(&port->state->port);
}
+/**
+ * cdns_rts_gpio_enable - Configure RTS/GPIO to high/low
+ * @cdns_uart: Handle to the cdns_uart
+ * @enable: Value to be set to RTS/GPIO
+ */
+static void cdns_rts_gpio_enable(struct cdns_uart *cdns_uart, bool enable)
+{
+ u32 val;
+
+ if (cdns_uart->gpiod_rts) {
+ gpiod_set_value(cdns_uart->gpiod_rts, enable);
+ } else {
+ val = readl(cdns_uart->port->membase + CDNS_UART_MODEMCR);
+ if (enable)
+ val &= ~CDNS_UART_MODEMCR_RTS;
+ else
+ val |= CDNS_UART_MODEMCR_RTS;
+ writel(val, cdns_uart->port->membase + CDNS_UART_MODEMCR);
+ }
+}
+
+/**
+ * cdns_rs485_tx_setup - Tx setup specific to rs485
+ * @cdns_uart: Handle to the cdns_uart
+ */
+static void cdns_rs485_tx_setup(struct cdns_uart *cdns_uart)
+{
+ if (cdns_uart->port->rs485.flags & SER_RS485_RTS_ON_SEND)
+ cdns_rts_gpio_enable(cdns_uart, 1);
+ else
+ cdns_rts_gpio_enable(cdns_uart, 0);
+
+ cdns_uart->rs485_tx_started = true;
+}
+
+/**
+ * cdns_rs485_rx_setup - Rx setup specific to rs485
+ * @cdns_uart: Handle to the cdns_uart
+ */
+static void cdns_rs485_rx_setup(struct cdns_uart *cdns_uart)
+{
+ if (cdns_uart->port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
+ cdns_rts_gpio_enable(cdns_uart, 1);
+ else
+ cdns_rts_gpio_enable(cdns_uart, 0);
+
+ cdns_uart->rs485_tx_started = false;
+}
+
/**
* cdns_uart_tx_empty - Check whether TX is empty
* @port: Handle to the uart port structure
@@ -579,6 +646,44 @@ static int cdns_uart_clk_notifier_cb(struct notifier_block *nb,
}
#endif
+/**
+ * cdns_rs485_rx_callback - Timer rx callback handler for rs485.
+ * @t: Handle to the timer list structure
+ */
+static void cdns_rs485_rx_callback(struct timer_list *t)
+{
+ struct cdns_uart *cdns_uart = from_timer(cdns_uart, t, timer);
+
+ /*
+ * Default Rx should be setup, because Rx signaling path
+ * need to enable to receive data.
+ */
+ cdns_rs485_rx_setup(cdns_uart);
+}
+
+/**
+ * cdns_rs485_tx_callback - Timer tx callback handler for rs485.
+ * @t: Handle to the timer list structure
+ */
+static void cdns_rs485_tx_callback(struct timer_list *t)
+{
+ struct cdns_uart *cdns_uart = from_timer(cdns_uart, t, timer);
+
+ uart_port_lock(cdns_uart->port);
+ cdns_uart_handle_tx(cdns_uart->port);
+
+ /* Enable the TX Empty interrupt */
+ writel(CDNS_UART_IXR_TXEMPTY, cdns_uart->port->membase + CDNS_UART_IER);
+ uart_port_unlock(cdns_uart->port);
+
+ if (uart_circ_empty(&cdns_uart->port->state->xmit) ||
+ uart_tx_stopped(cdns_uart->port)) {
+ timer_setup(&cdns_uart->timer, cdns_rs485_rx_callback, 0);
+ mod_timer(&cdns_uart->timer, jiffies +
+ msecs_to_jiffies(cdns_uart->port->rs485.delay_rts_after_send));
+ }
+}
+
/**
* cdns_uart_start_tx - Start transmitting bytes
* @port: Handle to the uart port structure
@@ -586,6 +691,7 @@ static int cdns_uart_clk_notifier_cb(struct notifier_block *nb,
static void cdns_uart_start_tx(struct uart_port *port)
{
unsigned int status;
+ struct cdns_uart *cdns_uart = port->private_data;
if (uart_tx_stopped(port))
return;
@@ -604,10 +710,40 @@ static void cdns_uart_start_tx(struct uart_port *port)
writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_ISR);
- cdns_uart_handle_tx(port);
+ if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED) {
+ if (!cdns_uart->rs485_tx_started) {
+ timer_setup(&cdns_uart->timer,
+ cdns_rs485_tx_callback, 0);
+ cdns_rs485_tx_setup(cdns_uart);
+ mod_timer(&cdns_uart->timer, jiffies +
+ msecs_to_jiffies(port->rs485.delay_rts_before_send));
+ } else {
+ if (!timer_pending(&cdns_uart->timer))
+ mod_timer(&cdns_uart->timer, jiffies);
+ }
+ } else {
+ cdns_uart_handle_tx(port);
- /* Enable the TX Empty interrupt */
- writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IER);
+ /* Enable the TX Empty interrupt */
+ writel(CDNS_UART_IXR_TXEMPTY, port->membase + CDNS_UART_IER);
+ }
+}
+
+/**
+ * cdns_rs485_stop_tx_callback - Timer stop tx callback handler for rs485.
+ * @t: Handle to the timer list structure
+ */
+static void cdns_rs485_stop_tx_callback(struct timer_list *t)
+{
+ unsigned int regval;
+ struct cdns_uart *cdns_uart = from_timer(cdns_uart, t, stop_tx_timer);
+
+ cdns_rs485_rx_setup(cdns_uart);
+
+ regval = readl(cdns_uart->port->membase + CDNS_UART_CR);
+ regval |= CDNS_UART_CR_TX_DIS;
+ /* Disable the transmitter */
+ writel(regval, cdns_uart->port->membase + CDNS_UART_CR);
}
/**
@@ -617,11 +753,19 @@ static void cdns_uart_start_tx(struct uart_port *port)
static void cdns_uart_stop_tx(struct uart_port *port)
{
unsigned int regval;
+ struct cdns_uart *cdns_uart = port->private_data;
- regval = readl(port->membase + CDNS_UART_CR);
- regval |= CDNS_UART_CR_TX_DIS;
- /* Disable the transmitter */
- writel(regval, port->membase + CDNS_UART_CR);
+ if ((cdns_uart->port->rs485.flags & SER_RS485_ENABLED) &&
+ !timer_pending(&cdns_uart->stop_tx_timer) &&
+ cdns_uart->rs485_tx_started) {
+ mod_timer(&cdns_uart->stop_tx_timer, jiffies +
+ msecs_to_jiffies(cdns_uart->port->rs485.delay_rts_after_send));
+ } else {
+ regval = readl(port->membase + CDNS_UART_CR);
+ regval |= CDNS_UART_CR_TX_DIS;
+ /* Disable the transmitter */
+ writel(regval, port->membase + CDNS_UART_CR);
+ }
}
/**
@@ -829,6 +973,12 @@ static int cdns_uart_startup(struct uart_port *port)
(CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
cpu_relax();
+ if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED) {
+ timer_setup(&cdns_uart->stop_tx_timer,
+ cdns_rs485_stop_tx_callback, 0);
+ cdns_rs485_rx_setup(cdns_uart);
+ }
+
/*
* Clear the RX disable bit and then set the RX enable bit to enable
* the receiver.
@@ -888,6 +1038,7 @@ static void cdns_uart_shutdown(struct uart_port *port)
{
int status;
unsigned long flags;
+ struct cdns_uart *cdns_uart = port->private_data;
uart_port_lock_irqsave(port, &flags);
@@ -903,6 +1054,11 @@ static void cdns_uart_shutdown(struct uart_port *port)
uart_port_unlock_irqrestore(port, flags);
free_irq(port->irq, port);
+
+ if (cdns_uart->port->rs485.flags & SER_RS485_ENABLED) {
+ del_timer_sync(&cdns_uart->timer);
+ del_timer_sync(&cdns_uart->stop_tx_timer);
+ }
}
/**
@@ -1032,7 +1188,7 @@ static void cdns_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
mode_reg &= ~CDNS_UART_MR_CHMODE_MASK;
if (mctrl & TIOCM_RTS)
- val |= CDNS_UART_MODEMCR_RTS;
+ cdns_rts_gpio_enable(cdns_uart_data, 1);
if (mctrl & TIOCM_DTR)
val |= CDNS_UART_MODEMCR_DTR;
if (mctrl & TIOCM_LOOP)
@@ -1455,6 +1611,37 @@ MODULE_DEVICE_TABLE(of, cdns_uart_of_match);
/* Temporary variable for storing number of instances */
static int instances;
+/**
+ * cdns_rs485_config - Called when an application calls TIOCSRS485 ioctl.
+ * @port: Pointer to the uart_port structure
+ * @termios: Pointer to the ktermios structure
+ * @rs485: Pointer to the serial_rs485 structure
+ *
+ * Return: 0
+ */
+static int cdns_rs485_config(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485)
+{
+ u32 val;
+ unsigned int ctrl_reg;
+
+ if (rs485->flags & SER_RS485_ENABLED) {
+ dev_dbg(port->dev, "Setting UART to RS485\n");
+ /* Make sure auto RTS is disabled */
+ val = readl(port->membase + CDNS_UART_MODEMCR);
+ val &= ~CDNS_UART_MODEMCR_FCM;
+ writel(val, port->membase + CDNS_UART_MODEMCR);
+ /* Disable transmitter and make Rx setup*/
+ cdns_uart_stop_tx(port);
+ } else {
+ /* Disable the TX and RX */
+ ctrl_reg = readl(port->membase + CDNS_UART_CR);
+ ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS;
+ writel(ctrl_reg, port->membase + CDNS_UART_CR);
+ }
+ return 0;
+}
+
/**
* cdns_uart_probe - Platform driver probe
* @pdev: Pointer to the platform device structure
@@ -1597,9 +1784,23 @@ static int cdns_uart_probe(struct platform_device *pdev)
port->private_data = cdns_uart_data;
port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG |
CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT;
+ port->rs485_config = cdns_rs485_config;
+ port->rs485_supported = cdns_rs485_supported;
cdns_uart_data->port = port;
platform_set_drvdata(pdev, port);
+ rc = uart_get_rs485_mode(port);
+ if (rc)
+ goto err_out_clk_notifier;
+
+ cdns_uart_data->gpiod_rts = devm_gpiod_get_optional(&pdev->dev, "rts",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(cdns_uart_data->gpiod_rts)) {
+ rc = PTR_ERR(cdns_uart_data->gpiod_rts);
+ dev_err(port->dev, "xuartps: devm_gpiod_get_optional failed\n");
+ goto err_out_clk_notifier;
+ }
+
pm_runtime_use_autosuspend(&pdev->dev);
pm_runtime_set_autosuspend_delay(&pdev->dev, UART_AUTOSUSPEND_TIMEOUT);
pm_runtime_set_active(&pdev->dev);
@@ -1618,6 +1819,8 @@ static int cdns_uart_probe(struct platform_device *pdev)
console_port = port;
}
#endif
+ if (cdns_uart_data->port->rs485.flags & SER_RS485_ENABLED)
+ cdns_rs485_rx_setup(cdns_uart_data);
rc = uart_add_one_port(&cdns_uart_uart_driver, port);
if (rc) {
@@ -1646,6 +1849,7 @@ static int cdns_uart_probe(struct platform_device *pdev)
pm_runtime_disable(&pdev->dev);
pm_runtime_set_suspended(&pdev->dev);
pm_runtime_dont_use_autosuspend(&pdev->dev);
+err_out_clk_notifier:
#ifdef CONFIG_COMMON_CLK
clk_notifier_unregister(cdns_uart_data->uartclk,
&cdns_uart_data->clk_rate_change_nb);
Add rs485 support to uartps driver. Use either rts-gpios or RTS to control RS485 phy as driver or a receiver. Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com> --- Changes for V2: Modify optional gpio name to xlnx,phy-ctrl-gpios. Update commit description. Add support for RTS, delay_rts_before_send and delay_rts_after_send in RS485 mode. Changes for V3: Modify optional gpio name to rts-gpios. Update commit description. Move cdns_uart_tx_empty function to avoid prototype statement. Remove assignment of struct serial_rs485 to port->rs485 as serial core performs that. Switch to native RTS in non GPIO case. Handle rs485 during stop tx. Remove explicit calls to configure gpio direction and value, as devm_gpiod_get_optional performs that by using GPIOD_OUT_LOW argument. Update implementation to support configuration of GPIO/RTS value based on user configuration of SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND. Move implementation to start_tx from handle_tx. Changes for V4: Create separate patch for cdns_uart_tx_empty relocation. Call cdns_rs485_rx_setup() before uart_add_one_port() in probe. Update gpio descriptor name to gpiod_rts. Instead of cdns_rs485_config_gpio_rts_high() and cdns_rs485_config_gpio_rts_low() functions for RTS/GPIO value configuration implement cdns_rts_gpio_enable(). Disable auto rts and call cdns_uart_stop_tx() from cdns_rs485_config. Use timer instead of mdelay for delay_rts_before_send and delay_rts_after_send. Update cdns_uart_set_mctrl to support GPIO/RTS. Changes for V5: None. Changes for V6: Disable the TX and RX in cdns_rs485_config() when rs485 disabled. Hold lock for cdns_uart_handle_tx() in cdns_rs485_tx_callback(). --- drivers/tty/serial/xilinx_uartps.c | 222 +++++++++++++++++++++++++++-- 1 file changed, 213 insertions(+), 9 deletions(-)