@@ -162,6 +162,22 @@ cf_gtr_isolation_pins: cf-gtr-isolation-pins {
marvell,function = "gpio";
};
+ cf_gtr_led_pins: led-pins {
+ marvell,pins = "mpp42", "mpp52";
+ marvell,function = "gpio";
+ };
+
+ cf_gtr_lte_disable_pins: lte-disable-pins {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+
+ cf_gtr_pci_pins: pci-pins {
+ // pci reset
+ marvell,pins = "mpp33", "mpp35", "mpp44";
+ marvell,function = "gpio";
+ };
+
cf_gtr_poe_reset_pins: cf-gtr-poe-reset-pins {
marvell,pins = "mpp48";
marvell,function = "gpio";
@@ -179,6 +195,12 @@ cf_gtr_sdhci_pins: cf-gtr-sdhci-pins {
marvell,function = "sd0";
};
+ cf_gtr_sfp0_pins: sfp0-pins {
+ /* sfp modabs, txdisable */
+ marvell,pins = "mpp25", "mpp46";
+ marvell,function = "gpio";
+ };
+
cf_gtr_spi1_cs_pins: spi1-cs-pins {
marvell,pins = "mpp59";
marvell,function = "spi1";
@@ -193,6 +215,11 @@ cf_gtr_usb3_con_vbus: cf-gtr-usb3-con-vbus {
marvell,pins = "mpp22";
marvell,function = "gpio";
};
+
+ cf_gtr_wifi_disable_pins: wifi-disable-pins {
+ marvell,pins = "mpp30", "mpp31";
+ marvell,function = "gpio";
+ };
};
sdhci@d8000 {
@@ -221,21 +248,26 @@ usb3@f8000 {
};
pcie {
+ pinctrl-0 = <&cf_gtr_pci_pins>;
+ pinctrl-names = "default";
status = "okay";
/*
* The PCIe units are accessible through
* the mini-PCIe connectors on the board.
*/
+ /* CON3 - serdes 0 */
pcie@1,0 {
reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
status = "okay";
};
+ /* CON4 - serdes 2 */
pcie@2,0 {
reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
status = "okay";
};
+ /* CON2 - serdes 4 */
pcie@3,0 {
reset-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
status = "okay";
@@ -243,10 +275,12 @@ pcie@3,0 {
};
};
+ /* CON5 */
sfp0: sfp {
compatible = "sff,sfp";
+ pinctrl-0 = <&cf_gtr_sfp0_pins>;
+ pinctrl-names = "default";
i2c-bus = <&i2c1>;
- los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpio0 25 GPIO_ACTIVE_LOW>;
tx-disable-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
};
@@ -273,6 +307,8 @@ button-1 {
gpio-leds {
compatible = "gpio-leds";
+ pinctrl-0 = <&cf_gtr_led_pins>;
+ pinctrl-names = "default";
led1 {
function = LED_FUNCTION_CPU;
@@ -408,7 +444,7 @@ &ahci1 {
};
&gpio0 {
- pinctrl-0 = <&cf_gtr_fan_pwm>;
+ pinctrl-0 = <&cf_gtr_fan_pwm &cf_gtr_wifi_disable_pins>;
pinctrl-names = "default";
wifi-disable {
@@ -420,7 +456,7 @@ wifi-disable {
};
&gpio1 {
- pinctrl-0 = <&cf_gtr_isolation_pins &cf_gtr_poe_reset_pins>;
+ pinctrl-0 = <&cf_gtr_isolation_pins &cf_gtr_poe_reset_pins &cf_gtr_lte_disable_pins>;
pinctrl-names = "default";
lte-disable {
Various control signals such as sfp module-absence, pci-e reset or led gpios were missing pinctrl nodes, leaving any u-boot choices in place. Since U-Boot is shared between multiple board variants, i.e. a388 clearfog pro / base, clearfog gtr l8 / s4, it is better to explicitly configure functions. Add explicit pinctrl entries for all gpios currently in use. Additionally the loss-of-signal gpio specified is invalid, in fact los only has a pull-up on the board but no gpio connection to the cpu. Remove this stray reference. Signed-off-by: Josua Mayer <josua@solid-run.com> --- .../boot/dts/marvell/armada-385-clearfog-gtr.dtsi | 42 ++++++++++++++++++++-- 1 file changed, 39 insertions(+), 3 deletions(-)