diff mbox series

[v3,5/9] arm64: dts: ti: k3-j721e-sk: Model CSI2RX connector mux

Message ID 20240208123233.391115-6-vaishnav.a@ti.com (mailing list archive)
State New, archived
Headers show
Series Add CSI2RX capture support on TI J7 platforms | expand

Commit Message

Vaishnav Achath Feb. 8, 2024, 12:32 p.m. UTC 
J721E SK has the CSI2RX routed to a MIPI CSI connector and to 15-pin
RPi camera connector through an analog mux with GPIO control, model that
so that an overlay can control the mux state according to connected
cameras. Also provide labels to the I2C mux bus instances so that a
generic overlay can be used across multiple platforms.

J721E SK schematics: https://www.ti.com/lit/zip/sprr438

Reviewed-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
---

V1->V2: Update commit message with schematics.

 arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 19 +++++++++++++++++--
 1 file changed, 17 insertions(+), 2 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
index 6950b1ff124f..5dbc85bc5038 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
@@ -286,6 +286,15 @@  tfp410_out: endpoint {
 			};
 		};
 	};
+
+	csi_mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-state-cells = <1>;
+		mux-gpios = <&main_gpio0 88 GPIO_ACTIVE_HIGH>;
+		idle-state = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&main_csi_mux_sel_pins_default>;
+	};
 };
 
 &main_pmx0 {
@@ -352,6 +361,12 @@  J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
 		>;
 	};
 
+	main_csi_mux_sel_pins_default: main-csi-mux-sel-default-pins {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x164, PIN_OUTPUT, 7) /* (V29) RGMII5_TD2 */
+		>;
+	};
+
 	dp0_pins_default: dp0-default-pins {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x1c4, PIN_INPUT, 5) /* SPI0_CS1.DP0_HPD */
@@ -858,14 +873,14 @@  i2c-mux@70 {
 		reg = <0x70>;
 
 		/* CSI0 I2C */
-		i2c@0 {
+		cam0_i2c: i2c@0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
 		};
 
 		/* CSI1 I2C */
-		i2c@1 {
+		cam1_i2c: i2c@1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;