| Message ID | 20240302095430.4871-3-wahrenst@gmx.net (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | pinctrl: bcm2835: Implement pin_conf_get | expand |
Sat, Mar 02, 2024 at 10:54:30AM +0100, Stefan Wahren kirjoitti: > The BCM2711 allows to read the bias config. So implement pin_conf_get > accordingly. The pull resistor values has been taken from the > BCM2711/7211 datasheet. > > This implementation assumes that BCM7211 behaves the same way. ... > + switch (param) { > + case PIN_CONFIG_BIAS_DISABLE: > + if (((val >> shift) & PUD_2711_MASK) == BCM2711_PULL_NONE) > + return 0; > + else > + return -EINVAL; Redundant 'else' in all cases. Also as in previous patch, use single return point of success. if (((val >> shift) & PUD_2711_MASK) != BCM2711_PULL_NONE) return -EINVAL; break; > + case PIN_CONFIG_BIAS_PULL_UP: > + if (((val >> shift) & PUD_2711_MASK) == BCM2711_PULL_UP) { > + *config = pinconf_to_config_packed(param, 50000); > + return 0; > + } else { > + return -EINVAL; > + } > + > + case PIN_CONFIG_BIAS_PULL_DOWN: > + if (((val >> shift) & PUD_2711_MASK) == BCM2711_PULL_DOWN) { > + *config = pinconf_to_config_packed(param, 50000); > + return 0; > + } else { > + return -EINVAL; > + } > + > + default: > + break; Return directly from here. return bcm2835_pinconf_get(pctldev, pin, config); > + } > + > + return bcm2835_pinconf_get(pctldev, pin, config); return 0; > +}
diff --git a/drivers/pinctrl/bcm/pinctrl-bcm2835.c b/drivers/pinctrl/bcm/pinctrl-bcm2835.c index b37c86ec6915..fcb9ab6729c0 100644 --- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c +++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c @@ -1112,6 +1112,47 @@ static const struct pinconf_ops bcm2835_pinconf_ops = { .pin_config_set = bcm2835_pinconf_set, }; +static int bcm2711_pinconf_get(struct pinctrl_dev *pctldev, unsigned pin, + unsigned long *config) +{ + struct bcm2835_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev); + enum pin_config_param param = pinconf_to_config_param(*config); + u32 offset, shift, val; + + offset = PUD_2711_REG_OFFSET(pin); + shift = PUD_2711_REG_SHIFT(pin); + val = bcm2835_gpio_rd(pc, GP_GPIO_PUP_PDN_CNTRL_REG0 + (offset * 4)); + + switch (param) { + case PIN_CONFIG_BIAS_DISABLE: + if (((val >> shift) & PUD_2711_MASK) == BCM2711_PULL_NONE) + return 0; + else + return -EINVAL; + + case PIN_CONFIG_BIAS_PULL_UP: + if (((val >> shift) & PUD_2711_MASK) == BCM2711_PULL_UP) { + *config = pinconf_to_config_packed(param, 50000); + return 0; + } else { + return -EINVAL; + } + + case PIN_CONFIG_BIAS_PULL_DOWN: + if (((val >> shift) & PUD_2711_MASK) == BCM2711_PULL_DOWN) { + *config = pinconf_to_config_packed(param, 50000); + return 0; + } else { + return -EINVAL; + } + + default: + break; + } + + return bcm2835_pinconf_get(pctldev, pin, config); +} + static void bcm2711_pull_config_set(struct bcm2835_pinctrl *pc, unsigned int pin, unsigned int arg) { @@ -1179,7 +1220,7 @@ static int bcm2711_pinconf_set(struct pinctrl_dev *pctldev, static const struct pinconf_ops bcm2711_pinconf_ops = { .is_generic = true, - .pin_config_get = bcm2835_pinconf_get, + .pin_config_get = bcm2711_pinconf_get, .pin_config_set = bcm2711_pinconf_set, };
The BCM2711 allows to read the bias config. So implement pin_conf_get accordingly. The pull resistor values has been taken from the BCM2711/7211 datasheet. This implementation assumes that BCM7211 behaves the same way. Signed-off-by: Stefan Wahren <wahrenst@gmx.net> --- drivers/pinctrl/bcm/pinctrl-bcm2835.c | 43 ++++++++++++++++++++++++++- 1 file changed, 42 insertions(+), 1 deletion(-) -- 2.34.1