| Message ID | 20240503062745.11298-1-wahrenst@gmx.net (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [V2] pinctrl: bcm2835: Make pin freeing behavior configurable | expand |
On Fri, May 3, 2024 at 8:28 AM Stefan Wahren <wahrenst@gmx.net> wrote: > Until now after a bcm2835 pin was freed its pinmux was set to GPIO_IN. > So in case it was configured as GPIO_OUT before the configured output > level also get lost. As long as GPIO sysfs was used this wasn't > actually a problem because the pins and their possible output level > were kept by sysfs. > > Since more and more Raspberry Pi users start using libgpiod they are > confused about this behavior. So make the pin freeing behavior of > GPIO_OUT configurable via module parameter. In case > pinctrl-bcm2835.persist_gpio_outputs is set to 1, the output level is > kept. > > This patch based on the downstream work of Phil Elwell. > > Link: https://github.com/raspberrypi/linux/pull/6117 > Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Patch applied! Yours, Linus Walleij
Fri, May 03, 2024 at 08:27:45AM +0200, Stefan Wahren kirjoitti: > Until now after a bcm2835 pin was freed its pinmux was set to GPIO_IN. > So in case it was configured as GPIO_OUT before the configured output > level also get lost. As long as GPIO sysfs was used this wasn't > actually a problem because the pins and their possible output level > were kept by sysfs. > > Since more and more Raspberry Pi users start using libgpiod they are > confused about this behavior. So make the pin freeing behavior of > GPIO_OUT configurable via module parameter. In case > pinctrl-bcm2835.persist_gpio_outputs is set to 1, the output level is > kept. > > This patch based on the downstream work of Phil Elwell. ... > +static bool persist_gpio_outputs; > +module_param(persist_gpio_outputs, bool, 0644); Do you need 'w' attribute? ... > + dev_info(dev, "GPIO_OUT persistence: %s\n", > + persist_gpio_outputs ? "yes" : "no"); str_yes_no() and with it can be put on a single line.
diff --git a/drivers/pinctrl/bcm/pinctrl-bcm2835.c b/drivers/pinctrl/bcm/pinctrl-bcm2835.c index f5a9372d43bd..b4293a827a89 100644 --- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c +++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c @@ -244,6 +244,10 @@ static const char * const irq_type_names[] = { [IRQ_TYPE_LEVEL_LOW] = "level-low", }; +static bool persist_gpio_outputs; +module_param(persist_gpio_outputs, bool, 0644); +MODULE_PARM_DESC(persist_gpio_outputs, "Enable GPIO_OUT persistence when pin is freed"); + static inline u32 bcm2835_gpio_rd(struct bcm2835_pinctrl *pc, unsigned reg) { return readl(pc->base + reg); @@ -926,6 +930,13 @@ static int bcm2835_pmx_free(struct pinctrl_dev *pctldev, unsigned offset) { struct bcm2835_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev); + enum bcm2835_fsel fsel = bcm2835_pinctrl_fsel_get(pc, offset); + + if (fsel == BCM2835_FSEL_GPIO_IN) + return 0; + + if (persist_gpio_outputs && fsel == BCM2835_FSEL_GPIO_OUT) + return 0; /* disable by setting to GPIO_IN */ bcm2835_pinctrl_fsel_set(pc, offset, BCM2835_FSEL_GPIO_IN); @@ -970,10 +981,7 @@ static void bcm2835_pmx_gpio_disable_free(struct pinctrl_dev *pctldev, struct pinctrl_gpio_range *range, unsigned offset) { - struct bcm2835_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev); - - /* disable by setting to GPIO_IN */ - bcm2835_pinctrl_fsel_set(pc, offset, BCM2835_FSEL_GPIO_IN); + bcm2835_pmx_free(pctldev, offset); } static int bcm2835_pmx_gpio_set_direction(struct pinctrl_dev *pctldev, @@ -1419,6 +1427,9 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev) goto out_remove; } + dev_info(dev, "GPIO_OUT persistence: %s\n", + persist_gpio_outputs ? "yes" : "no"); + return 0; out_remove:
Until now after a bcm2835 pin was freed its pinmux was set to GPIO_IN. So in case it was configured as GPIO_OUT before the configured output level also get lost. As long as GPIO sysfs was used this wasn't actually a problem because the pins and their possible output level were kept by sysfs. Since more and more Raspberry Pi users start using libgpiod they are confused about this behavior. So make the pin freeing behavior of GPIO_OUT configurable via module parameter. In case pinctrl-bcm2835.persist_gpio_outputs is set to 1, the output level is kept. This patch based on the downstream work of Phil Elwell. Link: https://github.com/raspberrypi/linux/pull/6117 Signed-off-by: Stefan Wahren <wahrenst@gmx.net> --- Changes in V2: - improve parameter name as suggested by Kent Gibson drivers/pinctrl/bcm/pinctrl-bcm2835.c | 19 +++++++++++++++---- 1 file changed, 15 insertions(+), 4 deletions(-) -- 2.34.1