@@ -6,6 +6,7 @@
/dts-v1/;
+#include <dt-bindings/usb/pd.h>
#include "imx8qm.dtsi"
/ {
@@ -109,6 +110,21 @@ lvds_backlight1: backlight-lvds1 {
default-brightness-level = <80>;
};
+ mux-controller {
+ compatible = "nxp,cbdtu02043", "gpio-sbu-mux";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec_mux>;
+ select-gpios = <&lsio_gpio4 6 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&lsio_gpio4 19 GPIO_ACTIVE_HIGH>;
+ orientation-switch;
+
+ port {
+ usb3_data_ss: endpoint {
+ remote-endpoint = <&typec_con_ss>;
+ };
+ };
+ };
+
reg_usdhc2_vmmc: usdhc2-vmmc {
compatible = "regulator-fixed";
regulator-name = "SD1_SPWR";
@@ -321,6 +337,44 @@ gyrometer@69 {
compatible = "st,l3g4200d-gyro";
reg = <0x69>;
};
+
+ ptn5110: tcpc@51 {
+ compatible = "nxp,ptn5110", "tcpci";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec>;
+ reg = <0x51>;
+ interrupt-parent = <&lsio_gpio4>;
+ interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+ status = "okay";
+
+ usb_con1: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "source";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ typec_dr_sw: endpoint {
+ remote-endpoint = <&usb3_drd_sw>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ typec_con_ss: endpoint {
+ remote-endpoint = <&usb3_data_ss>;
+ };
+ };
+ };
+ };
+ };
};
&i2c1 {
@@ -525,6 +579,26 @@ &usdhc2 {
status = "okay";
};
+&usb3_phy {
+ status = "okay";
+};
+
+&usbotg3 {
+ status = "okay";
+};
+
+&usbotg3_cdns3 {
+ dr_mode = "otg";
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ usb3_drd_sw: endpoint {
+ remote-endpoint = <&typec_dr_sw>;
+ };
+ };
+};
+
&sai0 {
#sound-dai-cells = <0>;
assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
@@ -791,6 +865,19 @@ IMX8QM_SAI1_TXC_AUD_SAI1_TXC 0x06000040
>;
};
+ pinctrl_typec: typecgrp {
+ fsl,pins = <
+ IMX8QM_QSPI1A_DATA0_LSIO_GPIO4_IO26 0x00000021
+ >;
+ };
+
+ pinctrl_typec_mux: typecmuxgrp {
+ fsl,pins = <
+ IMX8QM_QSPI1A_SS0_B_LSIO_GPIO4_IO19 0x60
+ IMX8QM_USB_SS3_TC3_LSIO_GPIO4_IO06 0x60
+ >;
+ };
+
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
Enable usb3.0 and related usb type C nodes. Signed-off-by: Frank Li <Frank.Li@nxp.com> --- arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 87 ++++++++++++++++++++++++++++ 1 file changed, 87 insertions(+)