diff mbox series

[v4] arm64: dts: ti: k3-am68-sk-som: Add support for OSPI flash

Message ID 20240622161835.3610348-1-u-kumar1@ti.com (mailing list archive)
State New, archived
Headers show
Series [v4] arm64: dts: ti: k3-am68-sk-som: Add support for OSPI flash | expand

Commit Message

Kumar, Udit June 22, 2024, 4:18 p.m. UTC 
From: Sinthu Raja <sinthu.raja@ti.com>

AM68 SK has an OSPI NOR flash on its SOM connected to OSPI0 instance.
Enable support for the same. Also, describe the OSPI flash partition
information through the device tree, according to the offsets in the
bootloader.

Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
Bootlogs
https://gist.github.com/uditkumarti/3a131e3c78f121cf8c2f703d307c02df#file-gistfile1-txt
line 1451

Changes in v4:
  a. Added bootph properties
  b. INT pin is not used by flash drivers, so dropping this
  c. reverting partition 0 offset to 512KB, due to DFU boot failure
     seen on other K3 SOC with 1MB offset.

Changes in v3:
  a. Fix the make dtbs_check error related to ospi pinctrl
  b. Increase the partition 0 size to 1MB and update the following
   partitions start address accordingly.

Changes in v2:
  a. remove pin E20, which is not connected.

v3: https://lore.kernel.org/all/20240226095231.35684-1-sinthu.raja@ti.com/
v2: https://lore.kernel.org/linux-arm-kernel/20240219075932.6458-1-sinthu.raja@ti.com/
v1: https://patchwork.kernel.org/project/linux-arm-kernel/patch/20240206092334.30307-1-sinthu.raja@ti.com/ 
 arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 81 ++++++++++++++++++++++
 1 file changed, 81 insertions(+)

Comments

Vignesh Raghavendra July 4, 2024, 7:52 a.m. UTC | #1 
Hi Udit Kumar,

On Sat, 22 Jun 2024 21:48:35 +0530, Udit Kumar wrote:
> AM68 SK has an OSPI NOR flash on its SOM connected to OSPI0 instance.
> Enable support for the same. Also, describe the OSPI flash partition
> information through the device tree, according to the offsets in the
> bootloader.
> 
> 

I have applied the following to branch ti-k3-dts-next on [1].
Thank you!

[1/1] arm64: dts: ti: k3-am68-sk-som: Add support for OSPI flash
      commit: 73f1f26e2e4cda4e105476708961f0c3aff4515e

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
index 2ebb7daa822f..5c66e0ec6e82 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
@@ -131,6 +131,25 @@  rtos_ipc_memory_region: ipc-memories@a8000000 {
 	};
 };
 
+&wkup_pmx0 {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+			J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+			J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+			J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+			J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+			J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+			J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+			J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+			J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+			J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+			J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+		>;
+	};
+};
+
 &wkup_pmx2 {
 	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
 		pinctrl-single,pins = <
@@ -153,6 +172,68 @@  eeprom@51 {
 	};
 };
 
+&ospi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+
+		partitions {
+			bootph-all;
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "ospi.tiboot3";
+				reg = <0x0 0x80000>;
+			};
+
+			partition@80000 {
+				label = "ospi.tispl";
+				reg = <0x80000 0x200000>;
+			};
+
+			partition@280000 {
+				label = "ospi.u-boot";
+				reg = <0x280000 0x400000>;
+			};
+
+			partition@680000 {
+				label = "ospi.env";
+				reg = <0x680000 0x40000>;
+			};
+
+			partition@740000 {
+				label = "ospi.env.backup";
+				reg = <0x740000 0x40000>;
+			};
+
+			partition@800000 {
+				label = "ospi.rootfs";
+				reg = <0x800000 0x37c0000>;
+			};
+
+			partition@3fc0000 {
+				bootph-pre-ram;
+				label = "ospi.phypattern";
+				reg = <0x3fc0000 0x40000>;
+			};
+		};
+	};
+};
+
 &mailbox0_cluster0 {
 	status = "okay";
 	interrupts = <436>;