diff mbox series

[v2,2/2] arm64: dts: rockchip: Add Xunlong Orange Pi 3B

Message ID 20240626230319.1425316-3-jonas@kwiboo.se (mailing list archive)
State New, archived
Headers show
Series arm64: dts: rockchip: Add Xunlong Orange Pi 3B | expand

Commit Message

Jonas Karlman June 26, 2024, 11:03 p.m. UTC
The Xunlong Orange Pi 3B is a single-board computer based on the
Rockchip RK3566 SoC.

Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
---
v2:
- Add DT for v2.1 hw revision, rename initial DT to v1.1:
  - Ethernet phy io voltage: 3v3 (v1.1) / 1v8 (v2.1)
  - Etherent reset gpios: GPIO3_C2 (v1.1) / GPIO4_C4 (v2.1)
  - WiFi/BT: CDW-20U5622 (v1.1) / AP6256 (v2.1)
- Rename led node and move led pinctrl props
- Use regulator-.* nodename for fixed regulators
- Drop rockchip,mic-in-differential prop
- Add cap-mmc-highspeed to sdhci node
- Add no-mmc and no-sd to sdmmc1 node

Following issue is reported by dtbs_check and is fixed by series at [1]:

  pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks'
    do not match any of the regexes: 'pinctrl-[0-9]+'
  from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#

[1] https://lore.kernel.org/all/20240622-rk809-fixes-v2-0-c0db420d3639@collabora.com/
---
 arch/arm64/boot/dts/rockchip/Makefile         |   2 +
 .../dts/rockchip/rk3566-orangepi-3b-v1.1.dts  |  29 +
 .../dts/rockchip/rk3566-orangepi-3b-v2.1.dts  |  70 ++
 .../boot/dts/rockchip/rk3566-orangepi-3b.dtsi | 678 ++++++++++++++++++
 4 files changed, 779 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi

Comments

kernel test robot June 28, 2024, 12:01 a.m. UTC | #1
Hi Jonas,

kernel test robot noticed the following build warnings:

[auto build test WARNING on rockchip/for-next]
[also build test WARNING on robh/for-next krzk/for-next krzk-dt/for-next krzk-mem-ctrl/for-next linus/master v6.10-rc5 next-20240627]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Jonas-Karlman/dt-bindings-arm-rockchip-Add-Xunlong-Orange-Pi-3B/20240627-175050
base:   https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git for-next
patch link:    https://lore.kernel.org/r/20240626230319.1425316-3-jonas%40kwiboo.se
patch subject: [PATCH v2 2/2] arm64: dts: rockchip: Add Xunlong Orange Pi 3B
config: arm64-randconfig-051-20240628 (https://download.01.org/0day-ci/archive/20240628/202406280724.E053qdhz-lkp@intel.com/config)
compiler: aarch64-linux-gcc (GCC) 13.2.0
dtschema version: 2024.6.dev2+g3b69bad
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240628/202406280724.E053qdhz-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202406280724.E053qdhz-lkp@intel.com/

dtcheck warnings: (new ones prefixed by >>)
>> arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dtb: pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
   	from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
--
>> arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dtb: pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
   	from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
kernel test robot June 28, 2024, 10:49 a.m. UTC | #2
Hi Jonas,

kernel test robot noticed the following build warnings:

[auto build test WARNING on rockchip/for-next]
[also build test WARNING on robh/for-next krzk/for-next krzk-dt/for-next krzk-mem-ctrl/for-next linus/master v6.10-rc5 next-20240627]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Jonas-Karlman/dt-bindings-arm-rockchip-Add-Xunlong-Orange-Pi-3B/20240627-175050
base:   https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git for-next
patch link:    https://lore.kernel.org/r/20240626230319.1425316-3-jonas%40kwiboo.se
patch subject: [PATCH v2 2/2] arm64: dts: rockchip: Add Xunlong Orange Pi 3B
config: arm64-randconfig-051-20240628 (https://download.01.org/0day-ci/archive/20240628/202406281834.nNnojcHy-lkp@intel.com/config)
compiler: aarch64-linux-gcc (GCC) 13.2.0
dtschema version: 2024.6.dev3+g650bf2d
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240628/202406281834.nNnojcHy-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202406281834.nNnojcHy-lkp@intel.com/

dtcheck warnings: (new ones prefixed by >>)
>> arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dtb: pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
   	from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
--
>> arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dtb: pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
   	from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ae0ae02f51e9..df5a74c407f4 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -81,6 +81,8 @@  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353ps.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353v.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353vs.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg503.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-orangepi-3b-v1.1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-orangepi-3b-v2.1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinetab2-v0.1.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
new file mode 100644
index 000000000000..074e93bd4b85
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
@@ -0,0 +1,29 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-orangepi-3b.dtsi"
+
+/ {
+	model = "Xunlong Orange Pi 3B v1.1";
+	compatible = "xunlong,orangepi-3b-v1.1", "xunlong,orangepi-3b", "rockchip,rk3566";
+};
+
+&pmu_io_domains {
+	vccio5-supply = <&vcc_3v3>;
+};
+
+&gmac1 {
+	phy-handle = <&rgmii_phy1>;
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <50000>;
+		reset-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts
new file mode 100644
index 000000000000..d894bff41e61
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts
@@ -0,0 +1,70 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-orangepi-3b.dtsi"
+
+/ {
+	model = "Xunlong Orange Pi 3B v2.1";
+	compatible = "xunlong,orangepi-3b-v2.1", "xunlong,orangepi-3b", "rockchip,rk3566";
+
+	vccio_phy1: regulator-1v8-vccio-phy {
+		compatible = "regulator-fixed";
+		regulator-name = "vccio_phy1";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+	};
+};
+
+&pmu_io_domains {
+	vccio5-supply = <&vccio_phy1>;
+};
+
+&gmac1 {
+	phy-handle = <&rgmii_phy1>;
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <50000>;
+		reset-gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&sdmmc1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PD6 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_wake_host_h>;
+	};
+};
+
+&uart1 {
+	bluetooth {
+		compatible = "brcm,bcm4345c5";
+		clocks = <&rk809 1>;
+		clock-names = "lpo";
+		interrupt-parent = <&gpio2>;
+		interrupts = <RK_PC0 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wakeup";
+		device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_reg_on_h &bt_wake_host_h &host_wake_bt_h>;
+		vbat-supply = <&vcc_3v3>;
+		vddio-supply = <&vcc_1v8>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi
new file mode 100644
index 000000000000..d539570f531e
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi
@@ -0,0 +1,678 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+	model = "Xunlong Orange Pi 3B";
+	compatible = "xunlong,orangepi-3b", "rockchip,rk3566";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc0;
+		mmc2 = &sdmmc1;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&work_led>;
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "on";
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	vcc3v3_pcie30: regulator-3v3-vcc-pcie30 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie20_pwren>;
+		regulator-name = "vcc3v3_pcie30";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	vcc3v3_sys: regulator-3v3-vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_sys: regulator-5v0-vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc5v0_usb_host: regulator-5v0-vcc-usb-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_host_pwren_h>;
+		regulator-name = "vcc5v0_usb_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb_otg: regulator-5v0-vcc-usb-otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_otg_pwren_h>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_reg_on_h>;
+		post-power-on-delay-ms = <200>;
+		power-off-delay-us = <5000000>;
+		reset-gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK809";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&rk809>;
+		};
+	};
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&combphy2 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+	clock_in_out = "input";
+	phy-mode = "rgmii-id";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m0_miim
+		     &gmac1m0_tx_bus2
+		     &gmac1m0_rx_bus2
+		     &gmac1m0_rgmii_clk
+		     &gmac1m0_rgmii_bus
+		     &gmac1m0_clkinout>;
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		#clock-cells = <1>;
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		clock-names = "mclk";
+		clock-output-names = "rk809-clkout1", "rk809-clkout2";
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
+		#sound-dai-cells = <0>;
+		system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <830000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc3v3_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
+&i2s1_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s1m0_sclktx
+		     &i2s1m0_lrcktx
+		     &i2s1m0_sdi0
+		     &i2s1m0_sdo0>;
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&pcie2x1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie20_pins>;
+	reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie30>;
+	status = "okay";
+};
+
+&pinctrl {
+	bluetooth {
+		bt_reg_on_h: bt-reg-on-h {
+			rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_wake_host_h: bt-wake-host-h {
+			rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		host_wake_bt_h: host-wake-bt-h {
+			rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		work_led: work-led {
+			rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie20_pins: pcie20-pins {
+			rockchip,pins =
+				<1 RK_PB0 4 &pcfg_pull_none>,
+				<0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>,
+				<1 RK_PB1 4 &pcfg_pull_none>;
+		};
+
+		pcie20_pwren: pcie20-pwren {
+			rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb {
+		usb_host_pwren_h: usb-host-pwren-h {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usb_otg_pwren_h: usb-otg-pwren-h {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	wifi {
+		wifi_reg_on_h: wifi-reg-on-h {
+			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		wifi_wake_host_h: wifi-wake-host-h {
+			rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio6-supply = <&vcc_3v3>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	no-mmc;
+	no-sd;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_clk &sdmmc1_cmd>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sfc {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <104000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb2phy1_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};