| Message ID | 20240627220001.692875-3-Frank.Li@nxp.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/7] arm64: dts: imx95: add edma[1..3] nodes | expand |
> Subject: [PATCH 3/7] arm64: dts: imx95-19x19-evk: Add audio related > nodes > > Add sai1, sai2. Add i2c4 and wm8962 and other dependent nodes. > > Signed-off-by: Frank Li <Frank.Li@nxp.com> > --- > .../boot/dts/freescale/imx95-19x19-evk.dts | 238 > ++++++++++++++++++ > 1 file changed, 238 insertions(+) > > diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > index d14a54ab4fd47..660e623f4f964 100644 > --- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > +++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > @@ -17,6 +17,11 @@ aliases { > serial0 = &lpuart1; > }; > > + bt_sco_codec: audio-codec-bt-sco { > + #sound-dai-cells = <1>; > + compatible = "linux,bt-sco"; > + }; > + > chosen { > stdout-path = &lpuart1; > }; > @@ -40,6 +45,34 @@ linux_cma: linux,cma { > }; > }; > > + reg_3p3v: regulator-3p3v { > + compatible = "regulator-fixed"; > + regulator-max-microvolt = <3300000>; > + regulator-min-microvolt = <3300000>; > + regulator-name = "+V3.3_SW"; > + }; > + > + reg_audio_pwr: regulator-audio-pwr { > + compatible = "regulator-fixed"; > + regulator-name = "audio-pwr"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&i2c4_gpio_expander_21 1 > GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-always-on; > + }; > + > + reg_audio_slot: regulator-audio-slot { > + compatible = "regulator-fixed"; > + regulator-name = "audio-wm8962"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&i2c4_gpio_expander_21 7 > GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-always-on; > + status = "disabled"; > + }; > + > reg_m2_pwr: regulator-m2-pwr { > compatible = "regulator-fixed"; > regulator-name = "M.2-power"; > @@ -79,6 +112,97 @@ reg_usdhc2_vmmc: regulator-usdhc2 { > enable-active-high; > off-on-delay-us = <12000>; > }; > + > + sound-bt-sco { > + compatible = "simple-audio-card"; > + simple-audio-card,name = "bt-sco-audio"; > + simple-audio-card,format = "dsp_a"; > + simple-audio-card,bitclock-inversion; > + simple-audio-card,frame-master = <&btcpu>; > + simple-audio-card,bitclock-master = <&btcpu>; > + > + btcpu: simple-audio-card,cpu { > + sound-dai = <&sai1>; > + dai-tdm-slot-num = <2>; > + dai-tdm-slot-width = <16>; > + }; > + > + simple-audio-card,codec { > + sound-dai = <&bt_sco_codec 1>; > + }; > + }; > + > + sound-micfil { > + compatible = "fsl,imx-audio-card"; > + model = "micfil-audio"; > + > + pri-dai-link { > + link-name = "micfil hifi"; > + format = "i2s"; > + cpu { > + sound-dai = <&micfil>; > + }; > + }; > + }; > + > + sound-wm8962 { > + compatible = "fsl,imx-audio-wm8962"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hp>; > + model = "wm8962-audio"; > + audio-cpu = <&sai3>; > + audio-codec = <&wm8962>; > + hp-det-gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>; > + audio-routing = "Headphone Jack", "HPOUTL", > + "Headphone Jack", "HPOUTR", > + "Ext Spk", "SPKOUTL", > + "Ext Spk", "SPKOUTR", > + "AMIC", "MICBIAS", > + "IN3R", "AMIC", > + "IN1R", "AMIC"; > + }; > +}; > + > +&lpi2c4 { > + clock-frequency = <400000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_lpi2c4>; > + status = "okay"; > + > + wm8962: audio-codec@1a { > + compatible = "wlf,wm8962"; > + reg = <0x1a>; > + clocks = <&scmi_clk IMX95_CLK_SAI3>; > + DCVDD-supply = <®_audio_pwr>; > + DBVDD-supply = <®_audio_pwr>; > + AVDD-supply = <®_audio_pwr>; > + CPVDD-supply = <®_audio_pwr>; > + MICVDD-supply = <®_audio_pwr>; > + PLLVDD-supply = <®_audio_pwr>; > + SPKVDD1-supply = <®_audio_pwr>; > + SPKVDD2-supply = <®_audio_pwr>; > + gpio-cfg = < 0x0000 /* 0:Default */ > + 0x0000 /* 1:Default */ > + 0x0000 /* 2:FN_DMICCLK */ > + 0x0000 /* 3:Default */ > + 0x0000 /* 4:FN_DMICCDAT */ > + 0x0000 /* 5:Default */ > + >; > + }; > + > + i2c4_gpio_expander_21: gpio@21 { Use gpio-expander@21? It is easy to duplicate the node if other i2c bus also has one. Regards, Peng. > + compatible = "nxp,pcal6408"; > + reg = <0x21>; > + #gpio-cells = <2>; > + gpio-controller; > + interrupt-controller; > + #interrupt-cells = <2>; > + interrupt-parent = <&gpio2>; > + interrupts = <18 IRQ_TYPE_LEVEL_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c4_pcal6408>; > + vcc-supply = <®_3p3v>; > + }; > }; > > &lpi2c7 { > @@ -108,6 +232,23 @@ &lpuart1 { > status = "okay"; > }; > > +&micfil { > + #sound-dai-cells = <0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pdm>; > + assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>, > + <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>, > + <&scmi_clk IMX95_CLK_AUDIOPLL1>, > + <&scmi_clk IMX95_CLK_AUDIOPLL2>, > + <&scmi_clk IMX95_CLK_PDM>; > + assigned-clock-parents = <0>, <0>, <0>, <0>, > + <&scmi_clk > IMX95_CLK_AUDIOPLL1>; > + assigned-clock-rates = <3932160000>, > + <3612672000>, <393216000>, > + <361267200>, <49152000>; > + status = "okay"; > +}; > + > &mu7 { > status = "okay"; > }; > @@ -128,6 +269,42 @@ &pcie1 { > status = "okay"; > }; > > +&sai1 { > + #sound-dai-cells = <0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sai1>; > + assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>, > + <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>, > + <&scmi_clk IMX95_CLK_AUDIOPLL1>, > + <&scmi_clk IMX95_CLK_AUDIOPLL2>, > + <&scmi_clk IMX95_CLK_SAI1>; > + assigned-clock-parents = <0>, <0>, <0>, <0>, > + <&scmi_clk > IMX95_CLK_AUDIOPLL1>; > + assigned-clock-rates = <3932160000>, > + <3612672000>, <393216000>, > + <361267200>, <12288000>; > + fsl,sai-mclk-direction-output; > + status = "okay"; > +}; > + > +&sai3 { > + #sound-dai-cells = <0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sai3>; > + assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>, > + <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>, > + <&scmi_clk IMX95_CLK_AUDIOPLL1>, > + <&scmi_clk IMX95_CLK_AUDIOPLL2>, > + <&scmi_clk IMX95_CLK_SAI3>; > + assigned-clock-parents = <0>, <0>, <0>, <0>, > + <&scmi_clk > IMX95_CLK_AUDIOPLL1>; > + assigned-clock-rates = <3932160000>, > + <3612672000>, <393216000>, > + <361267200>, <12288000>; > + fsl,sai-mclk-direction-output; > + status = "okay"; > +}; > + > &usdhc1 { > pinctrl-names = "default", "state_100mhz", "state_200mhz", > "sleep"; > pinctrl-0 = <&pinctrl_usdhc1>; > @@ -159,12 +336,31 @@ &wdog3 { > }; > > &scmi_iomuxc { > + pinctrl_hp: hpgrp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO11__GPIO2_IO_BIT11 > 0x31e > + >; > + }; > + > + pinctrl_i2c4_pcal6408: i2c4pcal6498grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO18__GPIO2_IO_BIT18 > 0x31e > + >; > + }; > + > pinctrl_i2c7_pcal6524: i2c7pcal6524grp { > fsl,pins = < > IMX95_PAD_GPIO_IO36__GPIO5_IO_BIT16 > 0x31e > >; > }; > > + pinctrl_lpi2c4: lpi2c4grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO30__LPI2C4_SDA > 0x40000b9e > + IMX95_PAD_GPIO_IO31__LPI2C4_SCL > 0x40000b9e > + >; > + }; > + > pinctrl_lpi2c7: lpi2c7grp { > fsl,pins = < > IMX95_PAD_GPIO_IO08__LPI2C7_SDA > 0x40000b9e > @@ -184,6 +380,48 @@ > IMX95_PAD_GPIO_IO35__HSIOMIX_TOP_PCIE2_CLKREQ_B > 0x4000031e > >; > }; > > + pinctrl_pdm: pdmgrp { > + fsl,pins = < > + > IMX95_PAD_PDM_CLK__AONMIX_TOP_PDM_CLK > 0x31e > + > IMX95_PAD_PDM_BIT_STREAM0__AONMIX_TOP_PDM_BIT_S > TREAM_BIT0 0x31e > + >; > + }; > + > + pinctrl_sai1: sai1grp { > + fsl,pins = < > + > IMX95_PAD_SAI1_RXD0__AONMIX_TOP_SAI1_RX_DATA_BIT0 > 0x31e > + > IMX95_PAD_SAI1_TXC__AONMIX_TOP_SAI1_TX_BCLK > 0x31e > + > IMX95_PAD_SAI1_TXFS__AONMIX_TOP_SAI1_TX_SYNC > 0x31e > + > IMX95_PAD_SAI1_TXD0__AONMIX_TOP_SAI1_TX_DATA_BIT0 > 0x31e > + >; > + }; > + > + pinctrl_sai2: sai2grp { > + fsl,pins = < > + > IMX95_PAD_ENET2_MDIO__NETCMIX_TOP_SAI2_RX_BCLK > 0x31e > + > IMX95_PAD_ENET2_MDC__NETCMIX_TOP_SAI2_RX_SYNC > 0x31e > + > IMX95_PAD_ENET2_TD3__NETCMIX_TOP_SAI2_RX_DATA_BIT > 0 0x31e > + > IMX95_PAD_ENET2_TD2__NETCMIX_TOP_SAI2_RX_DATA_BIT > 1 0x31e > + > IMX95_PAD_ENET2_TXC__NETCMIX_TOP_SAI2_TX_BCLK > 0x31e > + > IMX95_PAD_ENET2_TX_CTL__NETCMIX_TOP_SAI2_TX_SYNC > 0x31e > + > IMX95_PAD_ENET2_RX_CTL__NETCMIX_TOP_SAI2_TX_DATA_ > BIT0 0x31e > + > IMX95_PAD_ENET2_RXC__NETCMIX_TOP_SAI2_TX_DATA_BIT1 > 0x31e > + > IMX95_PAD_ENET2_RD0__NETCMIX_TOP_SAI2_TX_DATA_BIT > 2 0x31e > + > IMX95_PAD_ENET2_RD1__NETCMIX_TOP_SAI2_TX_DATA_BIT > 3 0x31e > + > IMX95_PAD_ENET2_RD2__NETCMIX_TOP_SAI2_MCLK > 0x31e > + >; > + }; > + > + pinctrl_sai3: sai3grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO17__SAI3_MCLK > 0x31e > + IMX95_PAD_GPIO_IO16__SAI3_TX_BCLK > 0x31e > + IMX95_PAD_GPIO_IO26__SAI3_TX_SYNC > 0x31e > + > IMX95_PAD_GPIO_IO20__SAI3_RX_DATA_BIT0 > 0x31e > + > IMX95_PAD_GPIO_IO21__SAI3_TX_DATA_BIT0 > 0x31e > + >; > + }; > + > pinctrl_uart1: uart1grp { > fsl,pins = < > > IMX95_PAD_UART1_RXD__AONMIX_TOP_LPUART1_RX > 0x31e > -- > 2.34.1 >
On Fri, Jun 28, 2024 at 12:03:27AM +0000, Peng Fan wrote: > > Subject: [PATCH 3/7] arm64: dts: imx95-19x19-evk: Add audio related > > nodes > > > > Add sai1, sai2. Add i2c4 and wm8962 and other dependent nodes. > > > > Signed-off-by: Frank Li <Frank.Li@nxp.com> > > --- > > .../boot/dts/freescale/imx95-19x19-evk.dts | 238 > > ++++++++++++++++++ > > 1 file changed, 238 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > > b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > > index d14a54ab4fd47..660e623f4f964 100644 > > --- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > > +++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > > @@ -17,6 +17,11 @@ aliases { > > serial0 = &lpuart1; > > }; > > ... > > + 0x0000 /* 4:FN_DMICCDAT */ > > + 0x0000 /* 5:Default */ > > + >; > > + }; > > + > > + i2c4_gpio_expander_21: gpio@21 { > > Use gpio-expander@21? > It is easy to duplicate the node if other i2c bus also > has one. It should be fine, parent node is difference. gpio-expander@21 can't resolve your problem. i2c2 { gpio-expander@21 {}; } i2c3 { gpio-expander@21 {}; } It should be same situation as gpio@21. DT should allow the same name under difference parent. Frank > > Regards, > Peng. >
> Subject: Re: [PATCH 3/7] arm64: dts: imx95-19x19-evk: Add audio > related nodes > > On Fri, Jun 28, 2024 at 12:03:27AM +0000, Peng Fan wrote: > > > Subject: [PATCH 3/7] arm64: dts: imx95-19x19-evk: Add audio > related > > > nodes > > > > > > Add sai1, sai2. Add i2c4 and wm8962 and other dependent nodes. > > > > > > Signed-off-by: Frank Li <Frank.Li@nxp.com> > > > --- > > > .../boot/dts/freescale/imx95-19x19-evk.dts | 238 > > > ++++++++++++++++++ > > > 1 file changed, 238 insertions(+) > > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > > > b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > > > index d14a54ab4fd47..660e623f4f964 100644 > > > --- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > > > +++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts > > > @@ -17,6 +17,11 @@ aliases { > > > serial0 = &lpuart1; > > > }; > > > > ... > > > + 0x0000 /* 4:FN_DMICCDAT */ > > > + 0x0000 /* 5:Default */ > > > + >; > > > + }; > > > + > > > + i2c4_gpio_expander_21: gpio@21 { > > > > Use gpio-expander@21? > > It is easy to duplicate the node if other i2c bus also has one. > > It should be fine, parent node is difference. gpio-expander@21 can't > resolve your problem. > > i2c2 > { > gpio-expander@21 {}; > } > > i2c3 > { > gpio-expander@21 {}; > } > > It should be same situation as gpio@21. > > DT should allow the same name under difference parent. As I recall, there is build error of duplicated node. Regards, Peng. > > Frank > > > > > Regards, > > Peng. > >
diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts index d14a54ab4fd47..660e623f4f964 100644 --- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts @@ -17,6 +17,11 @@ aliases { serial0 = &lpuart1; }; + bt_sco_codec: audio-codec-bt-sco { + #sound-dai-cells = <1>; + compatible = "linux,bt-sco"; + }; + chosen { stdout-path = &lpuart1; }; @@ -40,6 +45,34 @@ linux_cma: linux,cma { }; }; + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "+V3.3_SW"; + }; + + reg_audio_pwr: regulator-audio-pwr { + compatible = "regulator-fixed"; + regulator-name = "audio-pwr"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&i2c4_gpio_expander_21 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_audio_slot: regulator-audio-slot { + compatible = "regulator-fixed"; + regulator-name = "audio-wm8962"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&i2c4_gpio_expander_21 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + status = "disabled"; + }; + reg_m2_pwr: regulator-m2-pwr { compatible = "regulator-fixed"; regulator-name = "M.2-power"; @@ -79,6 +112,97 @@ reg_usdhc2_vmmc: regulator-usdhc2 { enable-active-high; off-on-delay-us = <12000>; }; + + sound-bt-sco { + compatible = "simple-audio-card"; + simple-audio-card,name = "bt-sco-audio"; + simple-audio-card,format = "dsp_a"; + simple-audio-card,bitclock-inversion; + simple-audio-card,frame-master = <&btcpu>; + simple-audio-card,bitclock-master = <&btcpu>; + + btcpu: simple-audio-card,cpu { + sound-dai = <&sai1>; + dai-tdm-slot-num = <2>; + dai-tdm-slot-width = <16>; + }; + + simple-audio-card,codec { + sound-dai = <&bt_sco_codec 1>; + }; + }; + + sound-micfil { + compatible = "fsl,imx-audio-card"; + model = "micfil-audio"; + + pri-dai-link { + link-name = "micfil hifi"; + format = "i2s"; + cpu { + sound-dai = <&micfil>; + }; + }; + }; + + sound-wm8962 { + compatible = "fsl,imx-audio-wm8962"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hp>; + model = "wm8962-audio"; + audio-cpu = <&sai3>; + audio-codec = <&wm8962>; + hp-det-gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>; + audio-routing = "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "Ext Spk", "SPKOUTL", + "Ext Spk", "SPKOUTR", + "AMIC", "MICBIAS", + "IN3R", "AMIC", + "IN1R", "AMIC"; + }; +}; + +&lpi2c4 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpi2c4>; + status = "okay"; + + wm8962: audio-codec@1a { + compatible = "wlf,wm8962"; + reg = <0x1a>; + clocks = <&scmi_clk IMX95_CLK_SAI3>; + DCVDD-supply = <®_audio_pwr>; + DBVDD-supply = <®_audio_pwr>; + AVDD-supply = <®_audio_pwr>; + CPVDD-supply = <®_audio_pwr>; + MICVDD-supply = <®_audio_pwr>; + PLLVDD-supply = <®_audio_pwr>; + SPKVDD1-supply = <®_audio_pwr>; + SPKVDD2-supply = <®_audio_pwr>; + gpio-cfg = < 0x0000 /* 0:Default */ + 0x0000 /* 1:Default */ + 0x0000 /* 2:FN_DMICCLK */ + 0x0000 /* 3:Default */ + 0x0000 /* 4:FN_DMICCDAT */ + 0x0000 /* 5:Default */ + >; + }; + + i2c4_gpio_expander_21: gpio@21 { + compatible = "nxp,pcal6408"; + reg = <0x21>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gpio2>; + interrupts = <18 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4_pcal6408>; + vcc-supply = <®_3p3v>; + }; }; &lpi2c7 { @@ -108,6 +232,23 @@ &lpuart1 { status = "okay"; }; +&micfil { + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pdm>; + assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>, + <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>, + <&scmi_clk IMX95_CLK_AUDIOPLL1>, + <&scmi_clk IMX95_CLK_AUDIOPLL2>, + <&scmi_clk IMX95_CLK_PDM>; + assigned-clock-parents = <0>, <0>, <0>, <0>, + <&scmi_clk IMX95_CLK_AUDIOPLL1>; + assigned-clock-rates = <3932160000>, + <3612672000>, <393216000>, + <361267200>, <49152000>; + status = "okay"; +}; + &mu7 { status = "okay"; }; @@ -128,6 +269,42 @@ &pcie1 { status = "okay"; }; +&sai1 { + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai1>; + assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>, + <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>, + <&scmi_clk IMX95_CLK_AUDIOPLL1>, + <&scmi_clk IMX95_CLK_AUDIOPLL2>, + <&scmi_clk IMX95_CLK_SAI1>; + assigned-clock-parents = <0>, <0>, <0>, <0>, + <&scmi_clk IMX95_CLK_AUDIOPLL1>; + assigned-clock-rates = <3932160000>, + <3612672000>, <393216000>, + <361267200>, <12288000>; + fsl,sai-mclk-direction-output; + status = "okay"; +}; + +&sai3 { + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>, + <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>, + <&scmi_clk IMX95_CLK_AUDIOPLL1>, + <&scmi_clk IMX95_CLK_AUDIOPLL2>, + <&scmi_clk IMX95_CLK_SAI3>; + assigned-clock-parents = <0>, <0>, <0>, <0>, + <&scmi_clk IMX95_CLK_AUDIOPLL1>; + assigned-clock-rates = <3932160000>, + <3612672000>, <393216000>, + <361267200>, <12288000>; + fsl,sai-mclk-direction-output; + status = "okay"; +}; + &usdhc1 { pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; pinctrl-0 = <&pinctrl_usdhc1>; @@ -159,12 +336,31 @@ &wdog3 { }; &scmi_iomuxc { + pinctrl_hp: hpgrp { + fsl,pins = < + IMX95_PAD_GPIO_IO11__GPIO2_IO_BIT11 0x31e + >; + }; + + pinctrl_i2c4_pcal6408: i2c4pcal6498grp { + fsl,pins = < + IMX95_PAD_GPIO_IO18__GPIO2_IO_BIT18 0x31e + >; + }; + pinctrl_i2c7_pcal6524: i2c7pcal6524grp { fsl,pins = < IMX95_PAD_GPIO_IO36__GPIO5_IO_BIT16 0x31e >; }; + pinctrl_lpi2c4: lpi2c4grp { + fsl,pins = < + IMX95_PAD_GPIO_IO30__LPI2C4_SDA 0x40000b9e + IMX95_PAD_GPIO_IO31__LPI2C4_SCL 0x40000b9e + >; + }; + pinctrl_lpi2c7: lpi2c7grp { fsl,pins = < IMX95_PAD_GPIO_IO08__LPI2C7_SDA 0x40000b9e @@ -184,6 +380,48 @@ IMX95_PAD_GPIO_IO35__HSIOMIX_TOP_PCIE2_CLKREQ_B 0x4000031e >; }; + pinctrl_pdm: pdmgrp { + fsl,pins = < + IMX95_PAD_PDM_CLK__AONMIX_TOP_PDM_CLK 0x31e + IMX95_PAD_PDM_BIT_STREAM0__AONMIX_TOP_PDM_BIT_STREAM_BIT0 0x31e + >; + }; + + pinctrl_sai1: sai1grp { + fsl,pins = < + IMX95_PAD_SAI1_RXD0__AONMIX_TOP_SAI1_RX_DATA_BIT0 0x31e + IMX95_PAD_SAI1_TXC__AONMIX_TOP_SAI1_TX_BCLK 0x31e + IMX95_PAD_SAI1_TXFS__AONMIX_TOP_SAI1_TX_SYNC 0x31e + IMX95_PAD_SAI1_TXD0__AONMIX_TOP_SAI1_TX_DATA_BIT0 0x31e + >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + IMX95_PAD_ENET2_MDIO__NETCMIX_TOP_SAI2_RX_BCLK 0x31e + IMX95_PAD_ENET2_MDC__NETCMIX_TOP_SAI2_RX_SYNC 0x31e + IMX95_PAD_ENET2_TD3__NETCMIX_TOP_SAI2_RX_DATA_BIT0 0x31e + IMX95_PAD_ENET2_TD2__NETCMIX_TOP_SAI2_RX_DATA_BIT1 0x31e + IMX95_PAD_ENET2_TXC__NETCMIX_TOP_SAI2_TX_BCLK 0x31e + IMX95_PAD_ENET2_TX_CTL__NETCMIX_TOP_SAI2_TX_SYNC 0x31e + IMX95_PAD_ENET2_RX_CTL__NETCMIX_TOP_SAI2_TX_DATA_BIT0 0x31e + IMX95_PAD_ENET2_RXC__NETCMIX_TOP_SAI2_TX_DATA_BIT1 0x31e + IMX95_PAD_ENET2_RD0__NETCMIX_TOP_SAI2_TX_DATA_BIT2 0x31e + IMX95_PAD_ENET2_RD1__NETCMIX_TOP_SAI2_TX_DATA_BIT3 0x31e + IMX95_PAD_ENET2_RD2__NETCMIX_TOP_SAI2_MCLK 0x31e + >; + }; + + pinctrl_sai3: sai3grp { + fsl,pins = < + IMX95_PAD_GPIO_IO17__SAI3_MCLK 0x31e + IMX95_PAD_GPIO_IO16__SAI3_TX_BCLK 0x31e + IMX95_PAD_GPIO_IO26__SAI3_TX_SYNC 0x31e + IMX95_PAD_GPIO_IO20__SAI3_RX_DATA_BIT0 0x31e + IMX95_PAD_GPIO_IO21__SAI3_TX_DATA_BIT0 0x31e + >; + }; + pinctrl_uart1: uart1grp { fsl,pins = < IMX95_PAD_UART1_RXD__AONMIX_TOP_LPUART1_RX 0x31e
Add sai1, sai2. Add i2c4 and wm8962 and other dependent nodes. Signed-off-by: Frank Li <Frank.Li@nxp.com> --- .../boot/dts/freescale/imx95-19x19-evk.dts | 238 ++++++++++++++++++ 1 file changed, 238 insertions(+)