new file mode 100644
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2024 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx93-kontron-osm-s.dtsi"
+
+/ {
+ model = "Kontron BL i.MX93 OSM-S";
+ compatible = "kontron,imx93-bl-osm-s", "kontron,imx93-osm-s", "fsl,imx93";
+
+ aliases {
+ ethernet0 = &fec;
+ ethernet1 = &eqos;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led1 {
+ label = "led1";
+ gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ pwm-beeper {
+ compatible = "pwm-beeper";
+ pwms = <&tpm6 1 5000 0>;
+ };
+
+ reg_vcc_panel: regulator-vcc-panel {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "VCC_PANEL";
+ };
+};
+
+&lpspi8 {
+ status = "okay";
+ assigned-clocks = <&clk IMX93_CLK_LPSPI8>;
+ assigned-clock-parents = <&clk IMX93_CLK_SYS_PLL_PFD0_DIV2>;
+ assigned-clock-rates = <100000000>;
+
+ eeram@0 {
+ compatible = "microchip,48l640";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&eqos { /* Second ethernet (OSM-S ETH_B) */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eqos_rgmii>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-id4f51.e91b";
+ reg = <1>;
+ reset-assert-us = <10000>;
+ reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&fec { /* First ethernet (OSM-S ETH_A) */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet_rgmii>;
+ phy-connection-type = "rgmii-id";
+ phy-handle = <ðphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-id4f51.e91b";
+ reg = <1>;
+ reset-assert-us = <10000>;
+ reset-gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&flexcan1 {
+ status = "okay";
+};
+
+&lpi2c2 {
+ status = "okay";
+
+ gpio_expander_dio: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "DIO1_OUT","DIO1_IN", "DIO2_OUT","DIO2_IN",
+ "DIO3_OUT","DIO3_IN", "DIO4_OUT","DIO4_IN";
+ interrupt-parent = <&gpio4>;
+ interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&lpuart1 {
+ status = "okay";
+};
+
+&lpuart7 {
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&lpuart6 {
+ linux,rs485-enabled-at-boot-time;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&tpm6 {
+ status = "okay";
+};
+
+&usbotg1 {
+ disable-over-current;
+ dr_mode = "host";
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb1@1 {
+ compatible = "usb424,2514";
+ reg = <1>;
+ };
+};
+
+&usbotg2 {
+ adp-disable;
+ hnp-disable;
+ srp-disable;
+
+ disable-over-current;
+ dr_mode = "otg";
+ usb-role-switch;
+ status = "okay";
+};
+
+&usdhc2 {
+ vmmc-supply = <®_vdd_3v3>;
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,547 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2024 Kontron Electronics GmbH
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx93.dtsi"
+
+/ {
+ model = "Kontron OSM-S i.MX93";
+ compatible = "kontron,imx93-osm-s", "fsl,imx93";
+
+ aliases {
+ rtc0 = &rv3028;
+ rtc1 = &bbnsm_rtc;
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x0 0x40000000 0 0x80000000>;
+ };
+
+ chosen {
+ stdout-path = &lpuart1;
+ };
+
+ reg_usdhc2_vcc: regulator-usdhc2-vcc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vcc>;
+ enable-active-high;
+ gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "VCC_SDIO_A";
+ };
+
+ reg_vdd_carrier: regulator-vdd-carrier {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_vdd_carrier>;
+ enable-active-high;
+ gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "VDD_CARRIER";
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ };
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+
+ regulator-state-disk {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&lpspi1 { /* OSM-S SPI_A */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpspi1>;
+ cs-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+};
+
+&lpspi8 { /* OSM-S SPI_B */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpspi8>;
+ cs-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+};
+
+&flexcan1 { /* OSM-S CAN_A */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+};
+
+&flexcan2 { /* OSM-S CAN_B */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+};
+
+&gpio1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio1>;
+ gpio-line-names = "", "", "I2C_A_SCL", "I2C_A_SDA",
+ "UART_CON_RX", "UART_CON_TX", "UART_C_RX", "UART_C_TX",
+ "CAN_A_TX", "CAN_A_RX", "GPIO_A_0", "SPI_A_CS0",
+ "SPI_A_SDI", "SPI_A_SCK","SPI_A_SDO";
+};
+
+&gpio2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio2>;
+ gpio-line-names = "I2C_B_SDA", "I2C_B_SCL", "GPIO_B_1", "GPIO_A_2",
+ "UART_B_TX", "UART_B_RX", "UART_B_RTS", "UART_B_CTS",
+ "UART_A_TX", "UART_A_RX", "UART_A_RTS", "UART_A_CTS",
+ "SPI_B_CS0", "SPI_B_SDI", "SPI_B_SDO", "SPI_B_SCK",
+ "I2S_BITCLK", "I2S_MCLK", "GPIO_A_1", "I2S_A_DATA_OUT",
+ "I2S_A_DATA_IN", "PWM_2", "GPIO_A_3", "PWM_1",
+ "PWM_0", "CAN_B_TX", "I2S_LRCLK", "CAN_B_RX", "GPIO_A_4",
+ "GPIO_A_5";
+};
+
+&gpio3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio3>;
+ gpio-line-names = "SDIO_A_CD", "SDIO_A_CLK", "SDIO_A_CMD", "SDIO_A_D0",
+ "SDIO_A_D1", "SDIO_A_D2", "SDIO_A_D3", "SDIO_A_PWR_EN",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "SDIO_B_CLK", "SDIO_B_CMD", "SDIO_B_D0", "SDIO_B_D1",
+ "SDIO_B_D2", "SDIO_B_D3", "GPIO_A_6", "GPIO_A_7";
+};
+
+&gpio4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio4>;
+ gpio-line-names = "ETH_B_MDC", "ETH_B_MDIO", "ETH_B_TXD4", "ETH_B_TXD3",
+ "ETH_B_TXD2", "ETH_B_TXD1", "ETH_B_TX_EN", "ETH_B_TX_CLK",
+ "ETH_B_RX_CTL", "ETH_B_RX_CLK", "ETH_B_RXD0", "ETH_B_RXD1",
+ "ETH_B_RXD2", "ETH_B_RXD3", "ETH_MDC", "ETH_MDIO",
+ "ETH_A_TXD3", "ETH_A_TXD2", "ETH_A_TXD1", "ETH_A_TXD0",
+ "ETH_A_TX_EN", "ETH_A_TX_CLK", "ETH_A_RX_CTL", "ETH_A_RX_CLK",
+ "ETH_A_RXD0", "ETH_A_RXD1", "ETH_A_RXD2", "ETH_A_RXD3",
+ "GPIO_B_0", "CARRIER_PWR_EN";
+};
+
+&lpi2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c1>;
+ status = "okay";
+
+ pca9451: pmic@25 {
+ compatible = "nxp,pca9451a";
+ reg = <0x25>;
+ nxp,i2c-lt-enable;
+
+ regulators {
+ reg_vdd_soc: BUCK1 { /* dual phase with BUCK3 */
+ regulator-name = "+0V8_VDD_SOC (BUCK1)";
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ reg_vddq_ddr: BUCK2 {
+ regulator-name = "+0V6_VDDQ_DDR (BUCK2)";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <600000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ reg_vdd_3v3: BUCK4 {
+ regulator-name = "+3V3 (BUCK4)";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdd_1v8: BUCK5 {
+ regulator-name = "+1V8 (BUCK5)";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_nvcc_dram: BUCK6 {
+ regulator-name = "+1V1_NVCC_DRAM (BUCK6)";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_nvcc_snvs: LDO1 {
+ regulator-name = "+1V8_NVCC_SNVS (LDO1)";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdd_ana: LDO4 {
+ regulator-name = "+0V8_VDD_ANA (LDO4)";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_nvcc_sd: LDO5 {
+ regulator-name = "NVCC_SD (LDO5)";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+ eeprom@50 {
+ compatible = "onnn,n24s64b", "atmel,24c64";
+ reg = <0x50>;
+ pagesize = <32>;
+ size = <8192>;
+ num-addresses = <1>;
+ };
+
+ rv3028: rtc@52 {
+ compatible = "microcrystal,rv3028";
+ reg = <0x52>;
+ };
+};
+
+&lpi2c2 { /* OSM-S I2C_A */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c2>;
+};
+
+&lpi2c3 { /* OSM-S I2C_B */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c3>;
+};
+
+&tpm3 { /* OSM-S PWM_0 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tpm3>;
+};
+
+&tpm4 { /* OSM-S PWM_2 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tpm4>;
+};
+
+&tpm6 { /* OSM-S PWM_1 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tpm6>;
+};
+
+&lpuart1 { /* OSM-S UART_CON */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart1>;
+};
+
+&lpuart2 { /* OSM-S UART_C */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart2>;
+};
+
+&lpuart6 { /* OSM-S UART_B */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart6>;
+};
+
+&lpuart7 { /* OSM-S UART_A */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart7>;
+};
+
+&usdhc1 { /* eMMC */
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1>;
+ pinctrl-2 = <&pinctrl_usdhc1>;
+ vmmc-supply = <®_vdd_3v3>;
+ vqmmc-supply = <®_vdd_1v8>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 { /* OSM-S SDIO_A */
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ vmmc-supply = <®_usdhc2_vcc>;
+ cd-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+};
+
+&usdhc3 { /* OSM-S SDIO_B */
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3>;
+ pinctrl-2 = <&pinctrl_usdhc3>;
+ vqmmc-supply = <®_vdd_1v8>;
+};
+
+&wdog3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_lpspi1: lpspi1grp {
+ fsl,pins = <
+ MX93_PAD_SAI1_TXC__LPSPI1_SIN 0x3fe /* SPI_A_SDI_(IO0) */
+ MX93_PAD_SAI1_RXD0__LPSPI1_SOUT 0x3fe /* SPI_A_SDO_(IO1) */
+ MX93_PAD_SAI1_TXD0__LPSPI1_SCK 0x3fe /* SPI_A_SCK */
+ MX93_PAD_SAI1_TXFS__GPIO1_IO11 0x3fe /* SPI_A_CS0# */
+ >;
+ };
+
+ pinctrl_lpspi8: lpspi8grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO13__LPSPI8_SIN 0x3fe /* SPI_B_SDI */
+ MX93_PAD_GPIO_IO14__LPSPI8_SOUT 0x3fe /* SPI_B_SDO */
+ MX93_PAD_GPIO_IO15__LPSPI8_SCK 0x3fe /* SPI_B_SCK */
+ MX93_PAD_GPIO_IO12__GPIO2_IO12 0x3fe /* SPI_B_CS0# */
+ >;
+ };
+
+ pinctrl_enet_rgmii: enetrgmiigrp {
+ fsl,pins = <
+ MX93_PAD_ENET2_MDC__ENET1_MDC 0x57e /* ETH_MDC */
+ MX93_PAD_ENET2_MDIO__ENET1_MDIO 0x57e /* ETH_MDIO */
+ MX93_PAD_ENET2_RD0__ENET1_RGMII_RD0 0x57e /* ETH_A_(S)(R)(G)MII_RXD0 */
+ MX93_PAD_ENET2_RD1__ENET1_RGMII_RD1 0x57e /* ETH_A_(S)(R)(G)MII_RXD1 */
+ MX93_PAD_ENET2_RD2__ENET1_RGMII_RD2 0x57e /* ETH_A_(R)(G)MII_RXD2 */
+ MX93_PAD_ENET2_RD3__ENET1_RGMII_RD3 0x57e /* ETH_A_(R)(G)MII_RXD3 */
+ MX93_PAD_ENET2_RXC__ENET1_RGMII_RXC 0x5fe /* ETH_A_(R)(G)MII_RX_CLK */
+ MX93_PAD_ENET2_RX_CTL__ENET1_RGMII_RX_CTL 0x57e /* ETH_A_(R)(G)MII_RX_DV(_ER) */
+ MX93_PAD_ENET2_TD0__ENET1_RGMII_TD0 0x57e /* ETH_A_(S)(R)(G)MII_TXD0 */
+ MX93_PAD_ENET2_TD1__ENET1_RGMII_TD1 0x57e /* ETH_A_(S)(R)(G)MII_TXD1 */
+ MX93_PAD_ENET2_TD2__ENET1_RGMII_TD2 0x57e /* ETH_A_(S)(R)(G)MII_TXD2 */
+ MX93_PAD_ENET2_TD3__ENET1_RGMII_TD3 0x57e /* ETH_A_(S)(R)(G)MII_TXD3 */
+ MX93_PAD_ENET2_TXC__ENET1_RGMII_TXC 0x5fe /* ETH_A_(R)(G)MII_TX_CLK */
+ MX93_PAD_ENET2_TX_CTL__ENET1_RGMII_TX_CTL 0x57e /* ETH_A_(R)(G)MII_TX_EN(_ER) */
+ >;
+ };
+
+ pinctrl_eqos_rgmii: eqosrgmiigrp {
+ fsl,pins = <
+ MX93_PAD_ENET1_MDC__ENET_QOS_MDC 0x57e /* ETH_B_MDC */
+ MX93_PAD_ENET1_MDIO__ENET_QOS_MDIO 0x57e /* ETH_B_MDIO */
+ MX93_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0 0x57e /* ETH_B_(S)(R)(G)MII_RXD0 */
+ MX93_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1 0x57e /* ETH_B_(S)(R)(G)MII_RXD1 */
+ MX93_PAD_ENET1_RD2__ENET_QOS_RGMII_RD2 0x57e /* ETH_B_(R)(G)MII_RXD2 */
+ MX93_PAD_ENET1_RD3__ENET_QOS_RGMII_RD3 0x57e /* ETH_B_(R)(G)MII_RXD3 */
+ MX93_PAD_ENET1_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x57e /* ETH_B_(R)(G)MII_RX_CLK */
+ MX93_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x57e /* ETH_B_(R)(G)MII_RX_DV(_ER) */
+ MX93_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0 0x57e /* ETH_B_(S)(R)(G)MII_TXD0 */
+ MX93_PAD_ENET1_TD1__ENET_QOS_RGMII_TD1 0x57e /* ETH_B_(S)(R)(G)MII_TXD1 */
+ MX93_PAD_ENET1_TD2__ENET_QOS_RGMII_TD2 0x57e /* ETH_B_(S)(R)(G)MII_TXD2 */
+ MX93_PAD_ENET1_TD3__ENET_QOS_RGMII_TD3 0x57e /* ETH_B_(S)(R)(G)MII_TXD3 */
+ MX93_PAD_ENET1_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x57e /* ETH_B_(R)(G)MII_TX_CLK */
+ MX93_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x57e /* ETH_B_(R)(G)MII_TX_EN(_ER) */
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX93_PAD_PDM_CLK__CAN1_TX 0x139e /* CAN_A_TX */
+ MX93_PAD_PDM_BIT_STREAM0__CAN1_RX 0x139e /* CAN_A_RX */
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO25__CAN2_TX 0x139e /* CAN_B_TX */
+ MX93_PAD_GPIO_IO27__CAN2_RX 0x139e /* CAN_B_RX */
+ >;
+ };
+
+ pinctrl_gpio1: gpio1grp {
+ fsl,pins = <
+ MX93_PAD_PDM_BIT_STREAM1__GPIO1_IO10 0x31e /* GPIO_A_0 */
+ >;
+ };
+
+ pinctrl_gpio2: gpio2grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO18__GPIO2_IO18 0x31e /* GPIO_A_1 */
+ MX93_PAD_GPIO_IO03__GPIO2_IO03 0x31e /* GPIO_A_2 */
+ MX93_PAD_GPIO_IO22__GPIO2_IO22 0x31e /* GPIO_A_3 */
+ MX93_PAD_GPIO_IO28__GPIO2_IO28 0x31e /* GPIO_A_4 */
+ MX93_PAD_GPIO_IO29__GPIO2_IO29 0x31e /* GPIO_A_5 */
+ MX93_PAD_GPIO_IO02__GPIO2_IO02 0x31e /* GPIO_B_1 */
+ >;
+ };
+
+ pinctrl_gpio3: gpio3grp {
+ fsl,pins = <
+ MX93_PAD_CCM_CLKO1__GPIO3_IO26 0x31e /* GPIO_A_6 */
+ MX93_PAD_CCM_CLKO2__GPIO3_IO27 0x31e /* GPIO_A_7 */
+ >;
+ };
+
+ pinctrl_gpio4: gpio4grp {
+ fsl,pins = <
+ MX93_PAD_CCM_CLKO3__GPIO4_IO28 0x31e /* GPIO_B_0 */
+ >;
+ };
+
+ pinctrl_lpi2c1: lpi2c1grp {
+ fsl,pins = <
+ MX93_PAD_I2C1_SCL__LPI2C1_SCL 0x40000b9e
+ MX93_PAD_I2C1_SDA__LPI2C1_SDA 0x40000b9e
+ >;
+ };
+
+ pinctrl_lpi2c2: lpi2c2grp {
+ fsl,pins = <
+ MX93_PAD_I2C2_SCL__LPI2C2_SCL 0x40000b9e /* I2C_A_SCL */
+ MX93_PAD_I2C2_SDA__LPI2C2_SDA 0x40000b9e /* I2C_A_SDA */
+ >;
+ };
+
+ pinctrl_lpi2c3: lpi2c3grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO01__LPI2C3_SCL 0x40000b9e /* I2C_B_SCL */
+ MX93_PAD_GPIO_IO00__LPI2C3_SDA 0x40000b9e /* I2C_B_SDA */
+ >;
+ };
+
+ pinctrl_tpm3: tpm3grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO24__TPM3_CH3 0x57e /* PWM_0 */
+ >;
+ };
+
+ pinctrl_tpm4: tpm4grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO21__TPM4_CH1 0x57e /* PWM_2 */
+ >;
+ };
+
+ pinctrl_tpm6: tpm6grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO23__TPM6_CH1 0x57e /* PWM_1 */
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vcc: regusdhc2vccgrp {
+ fsl,pins = <
+ MX93_PAD_SD2_RESET_B__GPIO3_IO07 0x31e /* SDIO_A_PWR_EN */
+ >;
+ };
+
+ pinctrl_reg_vdd_carrier: regvddcarriergrp {
+ fsl,pins = <
+ MX93_PAD_CCM_CLKO4__GPIO4_IO29 0x31e /* CARRIER_PWR_EN */
+ >;
+ };
+
+ pinctrl_sai3: sai3grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO20__SAI3_RX_DATA00 0x31e /* I2S_A_DATA_IN */
+ MX93_PAD_GPIO_IO19__SAI3_TX_DATA00 0x31e /* I2S_A_DATA_OUT */
+ MX93_PAD_GPIO_IO17__SAI3_MCLK 0x31e /* I2S_MCLK */
+ MX93_PAD_GPIO_IO26__SAI3_TX_SYNC 0x31e /* I2S_LRCLK */
+ MX93_PAD_GPIO_IO16__SAI3_TX_BCLK 0x31e /* I2S_BITCLK */
+ >;
+ };
+
+ pinctrl_lpuart1: lpuart1grp {
+ fsl,pins = <
+ MX93_PAD_UART1_RXD__LPUART1_RX 0x31e /* UART_CON_RX */
+ MX93_PAD_UART1_TXD__LPUART1_TX 0x31e /* UART_CON_TX */
+ >;
+ };
+
+ pinctrl_lpuart2: lpuart2grp {
+ fsl,pins = <
+ MX93_PAD_UART2_RXD__LPUART2_RX 0x31e /* UART_C_RX */
+ MX93_PAD_UART2_TXD__LPUART2_TX 0x31e /* UART_C_TX */
+ >;
+ };
+
+ pinctrl_lpuart6: lpuart6grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO05__LPUART6_RX 0x31e /* UART_B_RX */
+ MX93_PAD_GPIO_IO04__LPUART6_TX 0x31e /* UART_B_TX */
+ MX93_PAD_GPIO_IO07__LPUART6_RTS_B 0x31e /* UART_B_CTS */
+ MX93_PAD_GPIO_IO06__LPUART6_CTS_B 0x31e /* UART_B_RTS */
+ >;
+ };
+
+ pinctrl_lpuart7: lpuart7grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO09__LPUART7_RX 0x31e /* UART_A_RX */
+ MX93_PAD_GPIO_IO08__LPUART7_TX 0x31e /* UART_A_TX */
+ MX93_PAD_GPIO_IO11__LPUART7_RTS_B 0x31e /* UART_A_CTS */
+ MX93_PAD_GPIO_IO10__LPUART7_CTS_B 0x31e /* UART_A_RTS */
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX93_PAD_SD1_CLK__USDHC1_CLK 0x15fe
+ MX93_PAD_SD1_CMD__USDHC1_CMD 0x13fe
+ MX93_PAD_SD1_DATA0__USDHC1_DATA0 0x13fe
+ MX93_PAD_SD1_DATA1__USDHC1_DATA1 0x13fe
+ MX93_PAD_SD1_DATA2__USDHC1_DATA2 0x13fe
+ MX93_PAD_SD1_DATA3__USDHC1_DATA3 0x13fe
+ MX93_PAD_SD1_DATA4__USDHC1_DATA4 0x13fe
+ MX93_PAD_SD1_DATA5__USDHC1_DATA5 0x13fe
+ MX93_PAD_SD1_DATA6__USDHC1_DATA6 0x13fe
+ MX93_PAD_SD1_DATA7__USDHC1_DATA7 0x13fe
+ MX93_PAD_SD1_STROBE__USDHC1_STROBE 0x15fe
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX93_PAD_SD2_CLK__USDHC2_CLK 0x15fe /* SDIO_A_CLK */
+ MX93_PAD_SD2_CMD__USDHC2_CMD 0x13fe /* SDIO_A_CMD */
+ MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x13fe /* SDIO_A_D0 */
+ MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x13fe /* SDIO_A_D1 */
+ MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x13fe /* SDIO_A_D2 */
+ MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x13fe /* SDIO_A_D3 */
+ MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+ fsl,pins = <
+ MX93_PAD_SD2_CD_B__GPIO3_IO00 0x31e /* SDIO_A_CD# */
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX93_PAD_SD3_CLK__USDHC3_CLK 0x15fe /* SDIO_B_CLK */
+ MX93_PAD_SD3_CMD__USDHC3_CMD 0x13fe /* SDIO_B_CMD */
+ MX93_PAD_SD3_DATA0__USDHC3_DATA0 0x13fe /* SDIO_B_D0 */
+ MX93_PAD_SD3_DATA1__USDHC3_DATA1 0x13fe /* SDIO_B_D1 */
+ MX93_PAD_SD3_DATA2__USDHC3_DATA2 0x13fe /* SDIO_B_D2 */
+ MX93_PAD_SD3_DATA3__USDHC3_DATA3 0x13fe /* SDIO_B_D3 */
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX93_PAD_WDOG_ANY__WDOG1_WDOG_ANY 0xc6
+ >;
+ };
+};