| Message ID | 20240726113207.3393247-2-xu.yang_2@nxp.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v2,1/6] usb: phy: mxs: enable regulator phy-3p0 to improve signal qualilty | expand |
On 24-07-26 19:32:03, Xu Yang wrote: > IP require keep USBPHY2's clk always on, so USBPHY2 (PLL7) power can be > controlled by suspend signal. USB remote wakeup needs resume signal be > sent out as soon as possible to match USB requirements. > > Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Reviewed-by: Peter Chen <peter.chen@kernel.org> > > --- > Changes in v2: > - modify commit message > - remove hardware_control_phy2_clk > --- > drivers/usb/phy/phy-mxs-usb.c | 33 ++++++++++++++++++++++++++------- > 1 file changed, 26 insertions(+), 7 deletions(-) > > diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c > index d9d29f0b37de..e172af75f602 100644 > --- a/drivers/usb/phy/phy-mxs-usb.c > +++ b/drivers/usb/phy/phy-mxs-usb.c > @@ -150,6 +150,15 @@ > #define MXS_PHY_TX_D_CAL_MIN 79 > #define MXS_PHY_TX_D_CAL_MAX 119 > > +/* > + * At imx6q/6sl/6sx, the PHY2's clock is controlled by hardware directly, > + * eg, according to PHY's suspend status. In these PHYs, we only need to > + * open the clock at the initialization and close it at its shutdown routine. > + * These PHYs can send resume signal without software interfere if not > + * gate clock. > + */ > +#define MXS_PHY_HARDWARE_CONTROL_PHY2_CLK BIT(4) > + > struct mxs_phy_data { > unsigned int flags; > }; > @@ -161,12 +170,14 @@ static const struct mxs_phy_data imx23_phy_data = { > static const struct mxs_phy_data imx6q_phy_data = { > .flags = MXS_PHY_SENDING_SOF_TOO_FAST | > MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS | > - MXS_PHY_NEED_IP_FIX, > + MXS_PHY_NEED_IP_FIX | > + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK, > }; > > static const struct mxs_phy_data imx6sl_phy_data = { > .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS | > - MXS_PHY_NEED_IP_FIX, > + MXS_PHY_NEED_IP_FIX | > + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK, > }; > > static const struct mxs_phy_data vf610_phy_data = { > @@ -175,7 +186,8 @@ static const struct mxs_phy_data vf610_phy_data = { > }; > > static const struct mxs_phy_data imx6sx_phy_data = { > - .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS, > + .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS | > + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK, > }; > > static const struct mxs_phy_data imx6ul_phy_data = { > @@ -518,12 +530,19 @@ static int mxs_phy_suspend(struct usb_phy *x, int suspend) > } > writel(BM_USBPHY_CTRL_CLKGATE, > x->io_priv + HW_USBPHY_CTRL_SET); > - clk_disable_unprepare(mxs_phy->clk); > + if (!(mxs_phy->port_id == 1 && > + (mxs_phy->data->flags & > + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK))) > + clk_disable_unprepare(mxs_phy->clk); > } else { > mxs_phy_clock_switch_delay(); > - ret = clk_prepare_enable(mxs_phy->clk); > - if (ret) > - return ret; > + if (!(mxs_phy->port_id == 1 && > + (mxs_phy->data->flags & > + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK))) { > + ret = clk_prepare_enable(mxs_phy->clk); > + if (ret) > + return ret; > + } > writel(BM_USBPHY_CTRL_CLKGATE, > x->io_priv + HW_USBPHY_CTRL_CLR); > writel(0, x->io_priv + HW_USBPHY_PWD); > -- > 2.34.1 >
diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c index d9d29f0b37de..e172af75f602 100644 --- a/drivers/usb/phy/phy-mxs-usb.c +++ b/drivers/usb/phy/phy-mxs-usb.c @@ -150,6 +150,15 @@ #define MXS_PHY_TX_D_CAL_MIN 79 #define MXS_PHY_TX_D_CAL_MAX 119 +/* + * At imx6q/6sl/6sx, the PHY2's clock is controlled by hardware directly, + * eg, according to PHY's suspend status. In these PHYs, we only need to + * open the clock at the initialization and close it at its shutdown routine. + * These PHYs can send resume signal without software interfere if not + * gate clock. + */ +#define MXS_PHY_HARDWARE_CONTROL_PHY2_CLK BIT(4) + struct mxs_phy_data { unsigned int flags; }; @@ -161,12 +170,14 @@ static const struct mxs_phy_data imx23_phy_data = { static const struct mxs_phy_data imx6q_phy_data = { .flags = MXS_PHY_SENDING_SOF_TOO_FAST | MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS | - MXS_PHY_NEED_IP_FIX, + MXS_PHY_NEED_IP_FIX | + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK, }; static const struct mxs_phy_data imx6sl_phy_data = { .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS | - MXS_PHY_NEED_IP_FIX, + MXS_PHY_NEED_IP_FIX | + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK, }; static const struct mxs_phy_data vf610_phy_data = { @@ -175,7 +186,8 @@ static const struct mxs_phy_data vf610_phy_data = { }; static const struct mxs_phy_data imx6sx_phy_data = { - .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS, + .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS | + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK, }; static const struct mxs_phy_data imx6ul_phy_data = { @@ -518,12 +530,19 @@ static int mxs_phy_suspend(struct usb_phy *x, int suspend) } writel(BM_USBPHY_CTRL_CLKGATE, x->io_priv + HW_USBPHY_CTRL_SET); - clk_disable_unprepare(mxs_phy->clk); + if (!(mxs_phy->port_id == 1 && + (mxs_phy->data->flags & + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK))) + clk_disable_unprepare(mxs_phy->clk); } else { mxs_phy_clock_switch_delay(); - ret = clk_prepare_enable(mxs_phy->clk); - if (ret) - return ret; + if (!(mxs_phy->port_id == 1 && + (mxs_phy->data->flags & + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK))) { + ret = clk_prepare_enable(mxs_phy->clk); + if (ret) + return ret; + } writel(BM_USBPHY_CTRL_CLKGATE, x->io_priv + HW_USBPHY_CTRL_CLR); writel(0, x->io_priv + HW_USBPHY_PWD);
IP require keep USBPHY2's clk always on, so USBPHY2 (PLL7) power can be controlled by suspend signal. USB remote wakeup needs resume signal be sent out as soon as possible to match USB requirements. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> --- Changes in v2: - modify commit message - remove hardware_control_phy2_clk --- drivers/usb/phy/phy-mxs-usb.c | 33 ++++++++++++++++++++++++++------- 1 file changed, 26 insertions(+), 7 deletions(-)