| Message ID | 20240808071132.149251-24-herve.codina@bootlin.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | soc: fsl: Add support for QUICC Engine TSA and QMC | expand |
On Thu, Aug 08, 2024 at 09:11:16AM +0200, Herve Codina wrote: > Add support for the QMC (QUICC Multichannel Controller) available in > some PowerQUICC SoC that uses a QUICC Engine (QE) block such as MPC8321. > > This QE QMC is similar to the CPM QMC except that it uses UCCs (Unified > Communication Controllers) instead of SCCs (Serial Communication > Controllers). Also, compared against the CPM QMC, this QE QMC does not > use a fixed area for the UCC/SCC parameters area but it uses a dynamic > area allocated and provided to the hardware at runtime. > Last point, the QE QMC can use a firmware to have the QMC working in > 'soft-qmc' mode. > > Signed-off-by: Herve Codina <herve.codina@bootlin.com> > --- > .../soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml | 197 ++++++++++++++++++ > 1 file changed, 197 insertions(+) > create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml > > diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml > new file mode 100644 > index 000000000000..71ae64cb8a4f > --- /dev/null > +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml > @@ -0,0 +1,197 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: PowerQUICC QE QUICC Multichannel Controller (QMC) > + > +maintainers: > + - Herve Codina <herve.codina@bootlin.com> > + > +description: > + The QMC (QUICC Multichannel Controller) emulates up to 64 channels within one > + serial controller using the same TDM physical interface routed from TSA. > + > +properties: > + compatible: > + items: > + - enum: > + - fsl,mpc8321-ucc-qmc > + - const: fsl,qe-ucc-qmc > + > + reg: > + items: > + - description: UCC (Unified communication controller) register base > + - description: Dual port ram base > + > + reg-names: > + items: > + - const: ucc_regs _regs is redundant. > + - const: dpram > + > + interrupts: > + maxItems: 1 > + description: UCC interrupt line in the QE interrupt controller > + > + fsl,tsa-serial: > + $ref: /schemas/types.yaml#/definitions/phandle-array > + items: > + - items: > + - description: phandle to TSA node > + - enum: [1, 2, 3, 4, 5] > + description: | > + TSA serial interface (dt-bindings/soc/qe-fsl,tsa.h defines these > + values) > + - 1: UCC1 > + - 2: UCC2 > + - 3: UCC3 > + - 4: UCC4 > + - 5: UCC5 > + description: > + Should be a phandle/number pair. The phandle to TSA node and the TSA > + serial interface to use. > + > + fsl,soft-qmc: > + $ref: /schemas/types.yaml#/definitions/string > + description: > + Soft QMC firmware name to load. If this property is omitted, no firmware > + are used. "firmware-name" doesn't work here? > + > + '#address-cells': > + const: 1 > + > + '#size-cells': > + const: 0 > + > +patternProperties: > + '^channel@([0-9]|[1-5][0-9]|6[0-3])$': Unit-addresses are typically hex. > + description: > + A channel managed by this controller > + type: object > + additionalProperties: false > + > + properties: > + compatible: > + items: > + - enum: > + - fsl,mpc8321-ucc-qmc-hdlc > + - const: fsl,qe-ucc-qmc-hdlc > + - const: fsl,qmc-hdlc > + > + reg: > + minimum: 0 > + maximum: 63 > + description: > + The channel number > + > + fsl,operational-mode: > + $ref: /schemas/types.yaml#/definitions/string > + enum: [transparent, hdlc] > + default: transparent > + description: | > + The channel operational mode > + - hdlc: The channel handles HDLC frames > + - transparent: The channel handles raw data without any processing > + > + fsl,reverse-data: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + The bit order as seen on the channels is reversed, > + transmitting/receiving the MSB of each octet first. > + This flag is used only in 'transparent' mode. > + > + fsl,tx-ts-mask: > + $ref: /schemas/types.yaml#/definitions/uint64 > + description: > + Channel assigned Tx time-slots within the Tx time-slots routed by the > + TSA to this cell. > + > + fsl,rx-ts-mask: > + $ref: /schemas/types.yaml#/definitions/uint64 > + description: > + Channel assigned Rx time-slots within the Rx time-slots routed by the > + TSA to this cell. > + > + fsl,framer: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + phandle to the framer node. The framer is in charge of an E1/T1 line > + interface connected to the TDM bus. It can be used to get the E1/T1 line > + status such as link up/down. > + > + allOf: > + - if: > + properties: > + compatible: > + not: > + contains: > + const: fsl,qmc-hdlc "fsl,qmc-hdlc" is always present in compatible. This is only true if compatible is not present. If that's what you wanted, just do: if: not: required: [compatible] > + then: > + properties: > + fsl,framer: false Err, actually, you can do 1 better with just: dependencies: fsl,framer: [compatible] > + > + required: > + - reg > + - fsl,tx-ts-mask > + - fsl,rx-ts-mask > + > +required: > + - compatible > + - reg > + - reg-names > + - interrupts > + - fsl,tsa-serial > + - '#address-cells' > + - '#size-cells' > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/soc/qe-fsl,tsa.h> > + > + qmc@a60 { > + compatible = "fsl,mpc8321-ucc-qmc", "fsl,qe-ucc-qmc"; > + reg = <0x3200 0x200>, > + <0x10000 0x1000>; > + reg-names = "ucc_regs", "dpram"; > + interrupts = <35>; > + interrupt-parent = <&qeic>; > + fsl,soft-qmc = "fsl_qe_ucode_qmc_8321_11.bin"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + fsl,tsa-serial = <&tsa FSL_QE_TSA_UCC4>; > + > + channel@16 { > + /* Ch16 : First 4 even TS from all routed from TSA */ > + reg = <16>; > + fsl,operational-mode = "transparent"; > + fsl,reverse-data; > + fsl,tx-ts-mask = <0x00000000 0x000000aa>; > + fsl,rx-ts-mask = <0x00000000 0x000000aa>; > + }; > + > + channel@17 { > + /* Ch17 : First 4 odd TS from all routed from TSA */ > + reg = <17>; > + fsl,operational-mode = "transparent"; > + fsl,reverse-data; > + fsl,tx-ts-mask = <0x00000000 0x00000055>; > + fsl,rx-ts-mask = <0x00000000 0x00000055>; > + }; > + > + channel@19 { > + /* Ch19 : 8 TS (TS 8..15) from all routed from TSA */ > + compatible = "fsl,mpc8321-ucc-qmc-hdlc", > + "fsl,qe-ucc-qmc-hdlc", > + "fsl,qmc-hdlc"; > + reg = <19>; > + fsl,operational-mode = "hdlc"; > + fsl,tx-ts-mask = <0x00000000 0x0000ff00>; > + fsl,rx-ts-mask = <0x00000000 0x0000ff00>; > + fsl,framer = <&framer>; > + }; > + }; > -- > 2.45.0 >
Le 08/08/2024 à 09:11, Herve Codina a écrit : > Add support for the QMC (QUICC Multichannel Controller) available in > some PowerQUICC SoC that uses a QUICC Engine (QE) block such as MPC8321. > > This QE QMC is similar to the CPM QMC except that it uses UCCs (Unified > Communication Controllers) instead of SCCs (Serial Communication > Controllers). Also, compared against the CPM QMC, this QE QMC does not > use a fixed area for the UCC/SCC parameters area but it uses a dynamic > area allocated and provided to the hardware at runtime. > Last point, the QE QMC can use a firmware to have the QMC working in > 'soft-qmc' mode. > > Signed-off-by: Herve Codina <herve.codina@bootlin.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> > --- > .../soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml | 197 ++++++++++++++++++ > 1 file changed, 197 insertions(+) > create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml > > diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml > new file mode 100644 > index 000000000000..71ae64cb8a4f > --- /dev/null > +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml > @@ -0,0 +1,197 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: PowerQUICC QE QUICC Multichannel Controller (QMC) > + > +maintainers: > + - Herve Codina <herve.codina@bootlin.com> > + > +description: > + The QMC (QUICC Multichannel Controller) emulates up to 64 channels within one > + serial controller using the same TDM physical interface routed from TSA. > + > +properties: > + compatible: > + items: > + - enum: > + - fsl,mpc8321-ucc-qmc > + - const: fsl,qe-ucc-qmc > + > + reg: > + items: > + - description: UCC (Unified communication controller) register base > + - description: Dual port ram base > + > + reg-names: > + items: > + - const: ucc_regs > + - const: dpram > + > + interrupts: > + maxItems: 1 > + description: UCC interrupt line in the QE interrupt controller > + > + fsl,tsa-serial: > + $ref: /schemas/types.yaml#/definitions/phandle-array > + items: > + - items: > + - description: phandle to TSA node > + - enum: [1, 2, 3, 4, 5] > + description: | > + TSA serial interface (dt-bindings/soc/qe-fsl,tsa.h defines these > + values) > + - 1: UCC1 > + - 2: UCC2 > + - 3: UCC3 > + - 4: UCC4 > + - 5: UCC5 > + description: > + Should be a phandle/number pair. The phandle to TSA node and the TSA > + serial interface to use. > + > + fsl,soft-qmc: > + $ref: /schemas/types.yaml#/definitions/string > + description: > + Soft QMC firmware name to load. If this property is omitted, no firmware > + are used. > + > + '#address-cells': > + const: 1 > + > + '#size-cells': > + const: 0 > + > +patternProperties: > + '^channel@([0-9]|[1-5][0-9]|6[0-3])$': > + description: > + A channel managed by this controller > + type: object > + additionalProperties: false > + > + properties: > + compatible: > + items: > + - enum: > + - fsl,mpc8321-ucc-qmc-hdlc > + - const: fsl,qe-ucc-qmc-hdlc > + - const: fsl,qmc-hdlc > + > + reg: > + minimum: 0 > + maximum: 63 > + description: > + The channel number > + > + fsl,operational-mode: > + $ref: /schemas/types.yaml#/definitions/string > + enum: [transparent, hdlc] > + default: transparent > + description: | > + The channel operational mode > + - hdlc: The channel handles HDLC frames > + - transparent: The channel handles raw data without any processing > + > + fsl,reverse-data: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + The bit order as seen on the channels is reversed, > + transmitting/receiving the MSB of each octet first. > + This flag is used only in 'transparent' mode. > + > + fsl,tx-ts-mask: > + $ref: /schemas/types.yaml#/definitions/uint64 > + description: > + Channel assigned Tx time-slots within the Tx time-slots routed by the > + TSA to this cell. > + > + fsl,rx-ts-mask: > + $ref: /schemas/types.yaml#/definitions/uint64 > + description: > + Channel assigned Rx time-slots within the Rx time-slots routed by the > + TSA to this cell. > + > + fsl,framer: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + phandle to the framer node. The framer is in charge of an E1/T1 line > + interface connected to the TDM bus. It can be used to get the E1/T1 line > + status such as link up/down. > + > + allOf: > + - if: > + properties: > + compatible: > + not: > + contains: > + const: fsl,qmc-hdlc > + then: > + properties: > + fsl,framer: false > + > + required: > + - reg > + - fsl,tx-ts-mask > + - fsl,rx-ts-mask > + > +required: > + - compatible > + - reg > + - reg-names > + - interrupts > + - fsl,tsa-serial > + - '#address-cells' > + - '#size-cells' > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/soc/qe-fsl,tsa.h> > + > + qmc@a60 { > + compatible = "fsl,mpc8321-ucc-qmc", "fsl,qe-ucc-qmc"; > + reg = <0x3200 0x200>, > + <0x10000 0x1000>; > + reg-names = "ucc_regs", "dpram"; > + interrupts = <35>; > + interrupt-parent = <&qeic>; > + fsl,soft-qmc = "fsl_qe_ucode_qmc_8321_11.bin"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + fsl,tsa-serial = <&tsa FSL_QE_TSA_UCC4>; > + > + channel@16 { > + /* Ch16 : First 4 even TS from all routed from TSA */ > + reg = <16>; > + fsl,operational-mode = "transparent"; > + fsl,reverse-data; > + fsl,tx-ts-mask = <0x00000000 0x000000aa>; > + fsl,rx-ts-mask = <0x00000000 0x000000aa>; > + }; > + > + channel@17 { > + /* Ch17 : First 4 odd TS from all routed from TSA */ > + reg = <17>; > + fsl,operational-mode = "transparent"; > + fsl,reverse-data; > + fsl,tx-ts-mask = <0x00000000 0x00000055>; > + fsl,rx-ts-mask = <0x00000000 0x00000055>; > + }; > + > + channel@19 { > + /* Ch19 : 8 TS (TS 8..15) from all routed from TSA */ > + compatible = "fsl,mpc8321-ucc-qmc-hdlc", > + "fsl,qe-ucc-qmc-hdlc", > + "fsl,qmc-hdlc"; > + reg = <19>; > + fsl,operational-mode = "hdlc"; > + fsl,tx-ts-mask = <0x00000000 0x0000ff00>; > + fsl,rx-ts-mask = <0x00000000 0x0000ff00>; > + fsl,framer = <&framer>; > + }; > + };
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml new file mode 100644 index 000000000000..71ae64cb8a4f --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml @@ -0,0 +1,197 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PowerQUICC QE QUICC Multichannel Controller (QMC) + +maintainers: + - Herve Codina <herve.codina@bootlin.com> + +description: + The QMC (QUICC Multichannel Controller) emulates up to 64 channels within one + serial controller using the same TDM physical interface routed from TSA. + +properties: + compatible: + items: + - enum: + - fsl,mpc8321-ucc-qmc + - const: fsl,qe-ucc-qmc + + reg: + items: + - description: UCC (Unified communication controller) register base + - description: Dual port ram base + + reg-names: + items: + - const: ucc_regs + - const: dpram + + interrupts: + maxItems: 1 + description: UCC interrupt line in the QE interrupt controller + + fsl,tsa-serial: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to TSA node + - enum: [1, 2, 3, 4, 5] + description: | + TSA serial interface (dt-bindings/soc/qe-fsl,tsa.h defines these + values) + - 1: UCC1 + - 2: UCC2 + - 3: UCC3 + - 4: UCC4 + - 5: UCC5 + description: + Should be a phandle/number pair. The phandle to TSA node and the TSA + serial interface to use. + + fsl,soft-qmc: + $ref: /schemas/types.yaml#/definitions/string + description: + Soft QMC firmware name to load. If this property is omitted, no firmware + are used. + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + '^channel@([0-9]|[1-5][0-9]|6[0-3])$': + description: + A channel managed by this controller + type: object + additionalProperties: false + + properties: + compatible: + items: + - enum: + - fsl,mpc8321-ucc-qmc-hdlc + - const: fsl,qe-ucc-qmc-hdlc + - const: fsl,qmc-hdlc + + reg: + minimum: 0 + maximum: 63 + description: + The channel number + + fsl,operational-mode: + $ref: /schemas/types.yaml#/definitions/string + enum: [transparent, hdlc] + default: transparent + description: | + The channel operational mode + - hdlc: The channel handles HDLC frames + - transparent: The channel handles raw data without any processing + + fsl,reverse-data: + $ref: /schemas/types.yaml#/definitions/flag + description: + The bit order as seen on the channels is reversed, + transmitting/receiving the MSB of each octet first. + This flag is used only in 'transparent' mode. + + fsl,tx-ts-mask: + $ref: /schemas/types.yaml#/definitions/uint64 + description: + Channel assigned Tx time-slots within the Tx time-slots routed by the + TSA to this cell. + + fsl,rx-ts-mask: + $ref: /schemas/types.yaml#/definitions/uint64 + description: + Channel assigned Rx time-slots within the Rx time-slots routed by the + TSA to this cell. + + fsl,framer: + $ref: /schemas/types.yaml#/definitions/phandle + description: + phandle to the framer node. The framer is in charge of an E1/T1 line + interface connected to the TDM bus. It can be used to get the E1/T1 line + status such as link up/down. + + allOf: + - if: + properties: + compatible: + not: + contains: + const: fsl,qmc-hdlc + then: + properties: + fsl,framer: false + + required: + - reg + - fsl,tx-ts-mask + - fsl,rx-ts-mask + +required: + - compatible + - reg + - reg-names + - interrupts + - fsl,tsa-serial + - '#address-cells' + - '#size-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/soc/qe-fsl,tsa.h> + + qmc@a60 { + compatible = "fsl,mpc8321-ucc-qmc", "fsl,qe-ucc-qmc"; + reg = <0x3200 0x200>, + <0x10000 0x1000>; + reg-names = "ucc_regs", "dpram"; + interrupts = <35>; + interrupt-parent = <&qeic>; + fsl,soft-qmc = "fsl_qe_ucode_qmc_8321_11.bin"; + + #address-cells = <1>; + #size-cells = <0>; + + fsl,tsa-serial = <&tsa FSL_QE_TSA_UCC4>; + + channel@16 { + /* Ch16 : First 4 even TS from all routed from TSA */ + reg = <16>; + fsl,operational-mode = "transparent"; + fsl,reverse-data; + fsl,tx-ts-mask = <0x00000000 0x000000aa>; + fsl,rx-ts-mask = <0x00000000 0x000000aa>; + }; + + channel@17 { + /* Ch17 : First 4 odd TS from all routed from TSA */ + reg = <17>; + fsl,operational-mode = "transparent"; + fsl,reverse-data; + fsl,tx-ts-mask = <0x00000000 0x00000055>; + fsl,rx-ts-mask = <0x00000000 0x00000055>; + }; + + channel@19 { + /* Ch19 : 8 TS (TS 8..15) from all routed from TSA */ + compatible = "fsl,mpc8321-ucc-qmc-hdlc", + "fsl,qe-ucc-qmc-hdlc", + "fsl,qmc-hdlc"; + reg = <19>; + fsl,operational-mode = "hdlc"; + fsl,tx-ts-mask = <0x00000000 0x0000ff00>; + fsl,rx-ts-mask = <0x00000000 0x0000ff00>; + fsl,framer = <&framer>; + }; + };
Add support for the QMC (QUICC Multichannel Controller) available in some PowerQUICC SoC that uses a QUICC Engine (QE) block such as MPC8321. This QE QMC is similar to the CPM QMC except that it uses UCCs (Unified Communication Controllers) instead of SCCs (Serial Communication Controllers). Also, compared against the CPM QMC, this QE QMC does not use a fixed area for the UCC/SCC parameters area but it uses a dynamic area allocated and provided to the hardware at runtime. Last point, the QE QMC can use a firmware to have the QMC working in 'soft-qmc' mode. Signed-off-by: Herve Codina <herve.codina@bootlin.com> --- .../soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml | 197 ++++++++++++++++++ 1 file changed, 197 insertions(+) create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ucc-qmc.yaml