@@ -116,6 +116,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm-pcie1-ep.dtbo
# Boards with J722s SoC
+dtb-$(CONFIG_ARCH_K3) += k3-am67a-beagley-ai.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
# Boards with J784s4 SoC
new file mode 100644
@@ -0,0 +1,393 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * https://beagley-ai.org/
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ * Copyright (C) 2024 Robert Nelson, BeagleBoard.org Foundation
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "k3-j722s.dtsi"
+
+/ {
+ compatible = "beagle,am67a-beagley-ai", "ti,j722s";
+ model = "BeagleBoard.org BeagleY-AI";
+
+ aliases {
+ serial0 = &wkup_uart0;
+ serial2 = &main_uart0;
+ mmc1 = &sdhci1;
+ rtc0 = &rtc;
+ };
+
+ chosen {
+ stdout-path = &main_uart0;
+ };
+
+ memory@80000000 {
+ /* 4G RAM */
+ reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+ <0x00000008 0x80000000 0x00000000 0x80000000>;
+ device_type = "memory";
+ bootph-pre-ram;
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ secure_tfa_ddr: tfa@9e780000 {
+ reg = <0x00 0x9e780000 0x00 0x80000>;
+ no-map;
+ };
+
+ secure_ddr: optee@9e800000 {
+ reg = <0x00 0x9e800000 0x00 0x01800000>;
+ no-map;
+ };
+
+ wkup_r5fss0_core0_memory_region: r5f-memory@a0100000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa0100000 0x00 0xf00000>;
+ no-map;
+ };
+ };
+
+ vsys_5v0: regulator-1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ bootph-all;
+ };
+
+ vdd_3v3: regulator-2 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vsys_5v0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_mmc1: regulator-3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_3v3_sd_pins_default>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&main_gpio1 50 GPIO_ACTIVE_HIGH>;
+ bootph-all;
+ };
+
+ vdd_sd_dv: regulator-4 {
+ compatible = "regulator-gpio";
+ regulator-name = "tlv71033";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vsys_5v0>;
+ gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ bootph-all;
+ };
+
+ vsys_io_1v8: regulator-5 {
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_io_1v2: regulator-6 {
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_io_1v2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_default>;
+
+ led-0 {
+ gpios = <&main_gpio0 11 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-1 {
+ gpios = <&main_gpio0 12 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ function = LED_FUNCTION_HEARTBEAT;
+ default-state = "on";
+ };
+ };
+};
+
+&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x01e0, PIN_INPUT_PULLUP, 0) /* (D23) I2C0_SCL */
+ J722S_IOPAD(0x01e4, PIN_INPUT_PULLUP, 0) /* (B22) I2C0_SDA */
+ >;
+ bootph-all;
+ };
+
+ main_uart0_pins_default: main-uart0-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x01c8, PIN_INPUT, 0) /* (A22) UART0_RXD */
+ J722S_IOPAD(0x01cc, PIN_OUTPUT, 0) /* (B22) UART0_TXD */
+ >;
+ bootph-all;
+ };
+
+ vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x0244, PIN_OUTPUT, 7) /* (A24) MMC1_SDWP.GPIO1_49 */
+ >;
+ bootph-all;
+ };
+
+ main_mmc1_pins_default: main-mmc1-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x023c, PIN_INPUT, 0) /* (H22) MMC1_CMD */
+ J722S_IOPAD(0x0234, PIN_OUTPUT, 0) /* (H24) MMC1_CLK */
+ J722S_IOPAD(0x0230, PIN_INPUT, 0) /* (H23) MMC1_DAT0 */
+ J722S_IOPAD(0x022c, PIN_INPUT_PULLUP, 0) /* (H20) MMC1_DAT1 */
+ J722S_IOPAD(0x0228, PIN_INPUT_PULLUP, 0) /* (J23) MMC1_DAT2 */
+ J722S_IOPAD(0x0224, PIN_INPUT_PULLUP, 0) /* (H25) MMC1_DAT3 */
+ J722S_IOPAD(0x0240, PIN_INPUT, 7) /* (B24) MMC1_SDCD.GPIO1_48 */
+ >;
+ bootph-all;
+ };
+
+ mdio_pins_default: mdio-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AC24) MDIO0_MDC */
+ J722S_IOPAD(0x015c, PIN_INPUT, 0) /* (AD25) MDIO0_MDIO */
+ >;
+ };
+
+ rgmii1_pins_default: rgmii1-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x014c, PIN_INPUT, 0) /* (AC25) RGMII1_RD0 */
+ J722S_IOPAD(0x0150, PIN_INPUT, 0) /* (AD27) RGMII1_RD1 */
+ J722S_IOPAD(0x0154, PIN_INPUT, 0) /* (AE24) RGMII1_RD2 */
+ J722S_IOPAD(0x0158, PIN_INPUT, 0) /* (AE26) RGMII1_RD3 */
+ J722S_IOPAD(0x0148, PIN_INPUT, 0) /* (AE27) RGMII1_RXC */
+ J722S_IOPAD(0x0144, PIN_INPUT, 0) /* (AD23) RGMII1_RX_CTL */
+ J722S_IOPAD(0x0134, PIN_OUTPUT, 0) /* (AF27) RGMII1_TD0 */
+ J722S_IOPAD(0x0138, PIN_OUTPUT, 0) /* (AE23) RGMII1_TD1 */
+ J722S_IOPAD(0x013c, PIN_OUTPUT, 0) /* (AG25) RGMII1_TD2 */
+ J722S_IOPAD(0x0140, PIN_OUTPUT, 0) /* (AF24) RGMII1_TD3 */
+ J722S_IOPAD(0x0130, PIN_OUTPUT, 0) /* (AG26) RGMII1_TXC */
+ J722S_IOPAD(0x012c, PIN_OUTPUT, 0) /* (AF25) RGMII1_TX_CTL */
+ >;
+ };
+
+ led_pins_default: led-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x002c, PIN_OUTPUT, 7) /* (K26) OSPI0_CSn0.GPIO0_11 */
+ J722S_IOPAD(0x0030, PIN_OUTPUT, 7) /* (K23) OSPI0_CSn1.GPIO0_12 */
+ >;
+ };
+
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x01f4, PIN_INPUT_PULLUP, 0) /* (B23) EXTINTn */
+ >;
+ };
+
+ vdd_3v3_sd_pins_default: vdd-3v3-sd-default-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x0254, PIN_OUTPUT, 7) /* (E25) USB0_DRVVBUS.GPIO1_50 */
+ >;
+ };
+};
+
+&cpsw3g {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii1_pins_default>;
+ status = "okay";
+};
+
+&cpsw3g_mdio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins_default>;
+ status = "okay";
+
+ cpsw3g_phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
+&cpsw_port1 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy0>;
+ status = "okay";
+};
+
+&main_gpio1 {
+ status = "okay";
+};
+
+&main_uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart0_pins_default>;
+ bootph-all;
+ status = "okay";
+};
+
+&mcu_pmx0 {
+ wkup_uart0_pins_default: wkup-uart0-default-pins {
+ pinctrl-single,pins = <
+ J722S_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C7) WKUP_UART0_CTSn */
+ J722S_MCU_IOPAD(0x030, PIN_OUTPUT, 0) /* (C6) WKUP_UART0_RTSn */
+ J722S_MCU_IOPAD(0x024, PIN_INPUT, 0) /* (D8) WKUP_UART0_RXD */
+ J722S_MCU_IOPAD(0x028, PIN_OUTPUT, 0) /* (D7) WKUP_UART0_TXD */
+ >;
+ bootph-all;
+ };
+
+ wkup_i2c0_pins_default: wkup-i2c0-default-pins {
+ pinctrl-single,pins = <
+ J722S_MCU_IOPAD(0x04c, PIN_INPUT_PULLUP, 0) /* (C7) WKUP_I2C0_SCL */
+ J722S_MCU_IOPAD(0x050, PIN_INPUT_PULLUP, 0) /* (C6) WKUP_I2C1_SDA */
+ >;
+ bootph-all;
+ };
+};
+
+&wkup_uart0 {
+ /* WKUP UART0 is used by Device Manager firmware */
+ pinctrl-names = "default";
+ pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
+ status = "reserved";
+};
+
+&wkup_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wkup_i2c0_pins_default>;
+ clock-frequency = <100000>;
+ bootph-all;
+ status = "okay";
+
+ tps65219: pmic@30 {
+ compatible = "ti,tps65219";
+ reg = <0x30>;
+ buck1-supply = <&vsys_5v0>;
+ buck2-supply = <&vsys_5v0>;
+ buck3-supply = <&vsys_5v0>;
+ ldo1-supply = <&vdd_3v3>;
+ ldo3-supply = <&vdd_3v3>;
+ ldo4-supply = <&vdd_3v3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&gic500>;
+ interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ bootph-all;
+ system-power-controller;
+ ti,power-button;
+
+ regulators {
+ buck1_reg: buck1 {
+ regulator-name = "VDD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck2_reg: buck2 {
+ regulator-name = "VDD_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: ldo1 {
+ regulator-name = "VDDSHV5_SDIO";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-allow-bypass;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-name = "VDD_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-name = "VDDA_PHY_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-name = "VDDA_PLL_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ };
+
+ rtc: rtc@68 {
+ compatible = "dallas,ds1340";
+ reg = <0x68>;
+ };
+};
+
+&sdhci1 {
+ /* SD/MMC */
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ disable-wp;
+ cd-gpios = <&main_gpio1 48 GPIO_ACTIVE_LOW>;
+ cd-debounce-delay-ms = <100>;
+ bootph-all;
+ ti,fails-without-test-cd;
+ status = "okay";
+};
BeagleBoard.org BeagleY-AI is an easy to use, affordable open source hardware single board computer based on the Texas Instruments AM67A, which features a quad-core 64-bit Arm CPU subsystem, 2 general-purpose digital-signal-processors (DSP) and matrix-multiply-accelerators (MMA), GPU, vision and deep learning accelerators, and multiple Arm Cortex-R5 cores for low-power, low-latency GPIO control. https://beagley-ai.org/ https://openbeagle.org/beagley-ai/beagley-ai Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Rob Herring <robh@kernel.org> CC: Krzysztof Kozlowski <krzk+dt@kernel.org> CC: Conor Dooley <conor+dt@kernel.org> CC: Vignesh Raghavendra <vigneshr@ti.com> CC: Nishanth Menon <nm@ti.com> CC: Andrew Davis <afd@ti.com> CC: Jai Luthra <j-luthra@ti.com> CC: Roger Quadros <rogerq@kernel.org> CC: Siddharth Vadapalli <s-vadapalli@ti.com> CC: Jared McArthur <j-mcarthur@ti.com> CC: Andrei Aldea <a-aldea@ti.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Deepak Khatri <lorforlinux@beagleboard.org> CC: Drew Fustini <drew@beagleboard.org> --- Changes since v3: - removed extra blank lines - Krzysztof/Nishanth: switch to consistent regulator-x syntax along with dropping uppercase - Roger: removed un-used internal network clock: OBSCLK - Nishanth: fixed order of bootph-all before vendor prefixes - Nishanth: removed unused default-trigger with led-0 (dtbs_check failure) Changes since v2: - added led indictors - sdhci1 use MMC1_SDCD.GPIO1_48 for card detect - cleaned up order of status = "okay" - wkup_i2c0 moved to 100000 - eeprom added atmel,24c32 - rtc added dallas,ds1340 - sdhci1 use ti,fails-without-test-cd Changes since v1: - fixed incorrect vdd-3v3-sd-pins-default name - updated hdmi VDD_1V2 regulator for production pcb - switched device tree name from k3-j722s-beagley-ai to k3-am67a-beagley-ai - removed cpsw_port2 node - enable UHS support for MMCSD --- arch/arm64/boot/dts/ti/Makefile | 1 + .../arm64/boot/dts/ti/k3-am67a-beagley-ai.dts | 393 ++++++++++++++++++ 2 files changed, 394 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am67a-beagley-ai.dts