new file mode 100644
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 NXP
+ *
+ * Richard Zhu <hongxing.zhu@nxp.com>
+ */
+#include <dt-bindings/phy/phy.h>
+
+hsio_axi_clk: clock-hsio-axi {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <400000000>;
+ clock-output-names = "hsio_axi_clk";
+};
+
+hsio_per_clk: clock-hsio-per {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133333333>;
+ clock-output-names = "hsio_per_clk";
+};
+
+hsio_refa_clk: clock-hsio-refa {
+ compatible = "gpio-gate-clock";
+ clocks = <&xtal100m>;
+ #clock-cells = <0>;
+ enable-gpios = <&lsio_gpio4 27 GPIO_ACTIVE_LOW>;
+};
+
+hsio_refb_clk: clock-hsio-refb {
+ compatible = "gpio-gate-clock";
+ clocks = <&xtal100m>;
+ #clock-cells = <0>;
+ enable-gpios = <&lsio_gpio4 1 GPIO_ACTIVE_LOW>;
+};
+
+xtal100m: clock-xtal100m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "xtal_100MHz";
+};
+
+hsio_subsys: bus@5f000000 {
+ compatible = "simple-bus";
+ ranges = <0x5f000000 0x0 0x5f000000 0x01000000>,
+ <0x80000000 0x0 0x70000000 0x10000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ dma-ranges = <0x80000000 0 0x80000000 0x80000000>;
+
+ pcieb: pcie@5f010000 {
+ compatible = "fsl,imx8q-pcie";
+ reg = <0x5f010000 0x10000>,
+ <0x8ff00000 0x80000>;
+ reg-names = "dbi", "config";
+ ranges = <0x81000000 0 0x00000000 0x8ff80000 0 0x00010000>,
+ <0x82000000 0 0x80000000 0x80000000 0 0x0ff00000>;
+ #interrupt-cells = <1>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ clocks = <&pcieb_lpcg IMX_LPCG_CLK_6>,
+ <&pcieb_lpcg IMX_LPCG_CLK_4>,
+ <&pcieb_lpcg IMX_LPCG_CLK_5>;
+ clock-names = "dbi", "mstr", "slv";
+ bus-range = <0x00 0xff>;
+ device_type = "pci";
+ interrupt-map = <0 0 0 1 &gic 0 105 4>,
+ <0 0 0 2 &gic 0 106 4>,
+ <0 0 0 3 &gic 0 107 4>,
+ <0 0 0 4 &gic 0 108 4>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ num-lanes = <1>;
+ num-viewport = <4>;
+ power-domains = <&pd IMX_SC_R_PCIE_B>;
+ fsl,max-link-speed = <3>;
+ status = "disabled";
+ };
+
+ pcieb_lpcg: clock-controller@5f060000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f060000 0x10000>;
+ clocks = <&hsio_axi_clk>, <&hsio_axi_clk>, <&hsio_axi_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, <IMX_LPCG_CLK_6>;
+ clock-output-names = "hsio_pcieb_mstr_axi_clk",
+ "hsio_pcieb_slv_axi_clk",
+ "hsio_pcieb_dbi_axi_clk";
+ power-domains = <&pd IMX_SC_R_PCIE_B>;
+ };
+
+ phyx1_crr1_lpcg: clock-controller@5f0b0000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f0b0000 0x10000>;
+ clocks = <&hsio_per_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_4>;
+ clock-output-names = "hsio_phyx1_per_clk";
+ power-domains = <&pd IMX_SC_R_SERDES_1>;
+ };
+
+ pcieb_crr3_lpcg: clock-controller@5f0d0000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f0d0000 0x10000>;
+ clocks = <&hsio_per_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_4>;
+ clock-output-names = "hsio_pcieb_per_clk";
+ power-domains = <&pd IMX_SC_R_PCIE_B>;
+ };
+
+ misc_crr5_lpcg: clock-controller@5f0f0000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f0f0000 0x10000>;
+ clocks = <&hsio_per_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_4>;
+ clock-output-names = "hsio_misc_per_clk";
+ power-domains = <&pd IMX_SC_R_HSIO_GPIO>;
+ };
+};
new file mode 100644
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 NXP
+ */
+
+&hsio_subsys {
+ phyx1_lpcg: clock-controller@5f090000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f090000 0x10000>;
+ clocks = <&hsio_refb_clk>, <&hsio_per_clk>,
+ <&hsio_per_clk>, <&hsio_per_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>,
+ <IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_4>;
+ clock-output-names = "hsio_phyx1_pclk",
+ "hsio_phyx1_epcs_tx_clk",
+ "hsio_phyx1_epcs_rx_clk",
+ "hsio_phyx1_apb_clk";
+ power-domains = <&pd IMX_SC_R_SERDES_1>;
+ };
+
+ hsio_phy: phy@5f1a0000 {
+ compatible = "fsl,imx8qxp-hsio";
+ reg = <0x5f1a0000 0x10000>,
+ <0x5f120000 0x10000>,
+ <0x5f140000 0x10000>,
+ <0x5f160000 0x10000>;
+ reg-names = "reg", "phy", "ctrl", "misc";
+ clocks = <&phyx1_lpcg IMX_LPCG_CLK_0>,
+ <&phyx1_lpcg IMX_LPCG_CLK_4>,
+ <&phyx1_crr1_lpcg IMX_LPCG_CLK_4>,
+ <&pcieb_crr3_lpcg IMX_LPCG_CLK_4>,
+ <&misc_crr5_lpcg IMX_LPCG_CLK_4>;
+ clock-names = "pclk0", "apb_pclk0", "phy0_crr", "ctl0_crr",
+ "misc_crr";
+ #phy-cells = <3>;
+ power-domains = <&pd IMX_SC_R_SERDES_1>;
+ status = "disabled";
+ };
+};
+
+&pcieb {
+ #interrupt-cells = <1>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ interrupt-map = <0 0 0 1 &gic 0 47 4>,
+ <0 0 0 2 &gic 0 48 4>,
+ <0 0 0 3 &gic 0 49 4>,
+ <0 0 0 4 &gic 0 50 4>;
+ interrupt-map-mask = <0 0 0 0x7>;
+};
+
@@ -237,12 +237,14 @@ xtal24m: clock-xtal24m {
#include "imx8-ss-conn.dtsi"
#include "imx8-ss-ddr.dtsi"
#include "imx8-ss-lsio.dtsi"
+ #include "imx8-ss-hsio.dtsi"
};
#include "imx8dxl-ss-adma.dtsi"
#include "imx8dxl-ss-conn.dtsi"
#include "imx8dxl-ss-lsio.dtsi"
#include "imx8dxl-ss-ddr.dtsi"
+#include "imx8dxl-ss-hsio.dtsi"
&cm40_intmux {
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
new file mode 100644
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 NXP
+ * Richard Zhu <hongxing.zhu@nxp.com>
+ */
+
+&hsio_subsys {
+ compatible = "simple-bus";
+ ranges = <0x5f000000 0x0 0x5f000000 0x01000000>,
+ <0x40000000 0x0 0x60000000 0x10000000>,
+ <0x80000000 0x0 0x70000000 0x10000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ pciea: pcie@5f000000 {
+ compatible = "fsl,imx8q-pcie";
+ reg = <0x5f000000 0x10000>,
+ <0x4ff00000 0x80000>;
+ reg-names = "dbi", "config";
+ ranges = <0x81000000 0 0x00000000 0x4ff80000 0 0x00010000>,
+ <0x82000000 0 0x40000000 0x40000000 0 0x0ff00000>;
+ #interrupt-cells = <1>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ clocks = <&pciea_lpcg 2>,
+ <&pciea_lpcg 0>,
+ <&pciea_lpcg 1>;
+ clock-names = "dbi", "mstr", "slv";
+ bus-range = <0x00 0xff>;
+ device_type = "pci";
+ interrupt-map = <0 0 0 1 &gic 0 73 4>,
+ <0 0 0 2 &gic 0 74 4>,
+ <0 0 0 3 &gic 0 75 4>,
+ <0 0 0 4 &gic 0 76 4>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ num-lanes = <1>;
+ num-viewport = <4>;
+ power-domains = <&pd IMX_SC_R_PCIE_A>;
+ fsl,max-link-speed = <3>;
+ status = "disabled";
+ };
+
+ pcieb: pcie@5f010000 {
+ compatible = "fsl,imx8q-pcie";
+ reg = <0x5f010000 0x10000>,
+ <0x8ff00000 0x80000>;
+ reg-names = "dbi", "config";
+ ranges = <0x81000000 0 0x00000000 0x8ff80000 0 0x00010000>,
+ <0x82000000 0 0x80000000 0x80000000 0 0x0ff00000>;
+ #interrupt-cells = <1>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ clocks = <&pcieb_lpcg 2>,
+ <&pcieb_lpcg 0>,
+ <&pcieb_lpcg 1>;
+ clock-names = "dbi", "mstr", "slv";
+ bus-range = <0x00 0xff>;
+ device_type = "pci";
+ interrupt-map = <0 0 0 1 &gic 0 105 4>,
+ <0 0 0 2 &gic 0 106 4>,
+ <0 0 0 3 &gic 0 107 4>,
+ <0 0 0 4 &gic 0 108 4>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ num-lanes = <1>;
+ num-viewport = <4>;
+ power-domains = <&pd IMX_SC_R_PCIE_B>;
+ fsl,max-link-speed = <3>;
+ status = "disabled";
+ };
+
+ sata: sata@5f020000 {
+ compatible = "fsl,imx8qm-ahci";
+ reg = <0x5f020000 0x10000>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sata_lpcg 0>,
+ <&sata_crr4_lpcg 0>;
+ clock-names = "sata", "sata_ref";
+ phy-names = "sata-phy", "cali-phy0", "cali-phy1";
+ power-domains = <&pd IMX_SC_R_SATA_0>;
+ /*
+ * Since "REXT" pin is only present for first lane PHY
+ * and its calibration result will be stored, and shared
+ * by the PHY used by SATA.
+ *
+ * Add the calibration PHYs for SATA here, although only
+ * the third lane PHY is used by SATA.
+ */
+ phys = <&hsio_phy 2 PHY_TYPE_SATA 0>,
+ <&hsio_phy 0 PHY_TYPE_PCIE 0>,
+ <&hsio_phy 1 PHY_TYPE_PCIE 1>;
+ status = "disabled";
+ };
+
+ pciea_lpcg: clock-controller@5f050000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f050000 0x10000>;
+ clocks = <&hsio_axi_clk>, <&hsio_axi_clk>, <&hsio_axi_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, <IMX_LPCG_CLK_6>;
+ clock-output-names = "hsio_pciea_mstr_axi_clk",
+ "hsio_pciea_slv_axi_clk",
+ "hsio_pciea_dbi_axi_clk";
+ power-domains = <&pd IMX_SC_R_PCIE_A>;
+ };
+
+ sata_lpcg: clock-controller@5f070000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f070000 0x10000>;
+ clocks = <&hsio_axi_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_4>;
+ clock-output-names = "hsio_sata_clk";
+ power-domains = <&pd IMX_SC_R_SATA_0>;
+ };
+
+ phyx2_lpcg: clock-controller@5f080000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f080000 0x10000>;
+ clocks = <&hsio_refa_clk>, <&hsio_per_clk>,
+ <&hsio_refa_clk>, <&hsio_per_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>,
+ <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>;
+ clock-output-names = "hsio_phyx2_pclk_0",
+ "hsio_phyx2_pclk_1",
+ "hsio_phyx2_apbclk_0",
+ "hsio_phyx2_apbclk_1";
+ power-domains = <&pd IMX_SC_R_SERDES_0>;
+ };
+
+ phyx1_lpcg: clock-controller@5f090000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f090000 0x10000>;
+ clocks = <&hsio_refa_clk>, <&hsio_per_clk>,
+ <&hsio_per_clk>, <&hsio_per_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>,
+ <IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_4>;
+ clock-output-names = "hsio_phyx1_pclk",
+ "hsio_phyx1_epcs_tx_clk",
+ "hsio_phyx1_epcs_rx_clk",
+ "hsio_phyx1_apb_clk";
+ power-domains = <&pd IMX_SC_R_SERDES_1>;
+ };
+
+ phyx2_crr0_lpcg: clock-controller@5f0a0000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f0a0000 0x10000>;
+ clocks = <&hsio_per_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_4>;
+ clock-output-names = "hsio_phyx2_per_clk";
+ power-domains = <&pd IMX_SC_R_SERDES_0>;
+ };
+
+ pciea_crr2_lpcg: clock-controller@5f0c0000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f0c0000 0x10000>;
+ clocks = <&hsio_per_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_4>;
+ clock-output-names = "hsio_pciea_per_clk";
+ power-domains = <&pd IMX_SC_R_PCIE_A>;
+ };
+
+ sata_crr4_lpcg: clock-controller@5f0e0000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f0e0000 0x10000>;
+ clocks = <&hsio_per_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_4>;
+ clock-output-names = "hsio_sata_per_clk";
+ power-domains = <&pd IMX_SC_R_SATA_0>;
+ };
+
+ hsio_phy: phy@5f180000 {
+ compatible = "fsl,imx8qm-hsio";
+ reg = <0x5f180000 0x30000>,
+ <0x5f110000 0x20000>,
+ <0x5f130000 0x30000>,
+ <0x5f160000 0x10000>;
+ reg-names = "reg", "phy", "ctrl", "misc";
+ clocks = <&phyx2_lpcg IMX_LPCG_CLK_0>,
+ <&phyx2_lpcg IMX_LPCG_CLK_1>,
+ <&phyx2_lpcg IMX_LPCG_CLK_4>,
+ <&phyx2_lpcg IMX_LPCG_CLK_5>,
+ <&phyx1_lpcg IMX_LPCG_CLK_0>,
+ <&phyx1_lpcg IMX_LPCG_CLK_1>,
+ <&phyx1_lpcg IMX_LPCG_CLK_2>,
+ <&phyx1_lpcg IMX_LPCG_CLK_4>,
+ <&phyx2_crr0_lpcg IMX_LPCG_CLK_4>,
+ <&phyx1_crr1_lpcg IMX_LPCG_CLK_4>,
+ <&pciea_crr2_lpcg IMX_LPCG_CLK_4>,
+ <&pcieb_crr3_lpcg IMX_LPCG_CLK_4>,
+ <&sata_crr4_lpcg IMX_LPCG_CLK_4>,
+ <&misc_crr5_lpcg IMX_LPCG_CLK_4>;
+ clock-names = "pclk0", "pclk1", "apb_pclk0", "apb_pclk1",
+ "pclk2", "epcs_tx", "epcs_rx", "apb_pclk2",
+ "phy0_crr", "phy1_crr", "ctl0_crr",
+ "ctl1_crr", "ctl2_crr", "misc_crr";
+ #phy-cells = <3>;
+ power-domains = <&pd IMX_SC_R_SERDES_0>, <&pd IMX_SC_R_SERDES_1>;
+ status = "disabled";
+ };
+};
@@ -594,6 +594,7 @@ mipi_pll_div2_clk: clock-controller-mipi-div2-pll {
#include "imx8-ss-dma.dtsi"
#include "imx8-ss-conn.dtsi"
#include "imx8-ss-lsio.dtsi"
+ #include "imx8-ss-hsio.dtsi"
};
#include "imx8qm-ss-img.dtsi"
@@ -603,3 +604,4 @@ mipi_pll_div2_clk: clock-controller-mipi-div2-pll {
#include "imx8qm-ss-audio.dtsi"
#include "imx8qm-ss-lvds.dtsi"
#include "imx8qm-ss-mipi.dtsi"
+#include "imx8qm-ss-hsio.dtsi"
new file mode 100644
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 NXP
+ * Richard Zhu <hongxing.zhu@nxp.com>
+ */
+
+&hsio_subsys {
+ phyx1_lpcg: clock-controller@5f090000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x5f090000 0x10000>;
+ clocks = <&hsio_refb_clk>, <&hsio_per_clk>,
+ <&hsio_per_clk>, <&hsio_per_clk>;
+ #clock-cells = <1>;
+ clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>,
+ <IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_4>;
+ clock-output-names = "hsio_phyx1_pclk",
+ "hsio_phyx1_epcs_tx_clk",
+ "hsio_phyx1_epcs_rx_clk",
+ "hsio_phyx1_apb_clk";
+ power-domains = <&pd IMX_SC_R_SERDES_1>;
+ };
+
+ hsio_phy: phy@5f1a0000 {
+ compatible = "fsl,imx8qxp-hsio";
+ reg = <0x5f1a0000 0x10000>,
+ <0x5f120000 0x10000>,
+ <0x5f140000 0x10000>,
+ <0x5f160000 0x10000>;
+ reg-names = "reg", "phy", "ctrl", "misc";
+ clocks = <&phyx1_lpcg IMX_LPCG_CLK_0>,
+ <&phyx1_lpcg IMX_LPCG_CLK_1>,
+ <&phyx1_crr1_lpcg IMX_LPCG_CLK_4>,
+ <&pcieb_crr3_lpcg IMX_LPCG_CLK_4>,
+ <&misc_crr5_lpcg IMX_LPCG_CLK_4>;
+ clock-names = "pclk0", "apb_pclk0", "phy0_crr", "ctl0_crr",
+ "misc_crr";
+ #phy-cells = <3>;
+ power-domains = <&pd IMX_SC_R_SERDES_1>;
+ status = "disabled";
+ };
+};
@@ -323,6 +323,7 @@ map0 {
#include "imx8-ss-conn.dtsi"
#include "imx8-ss-ddr.dtsi"
#include "imx8-ss-lsio.dtsi"
+ #include "imx8-ss-hsio.dtsi"
};
#include "imx8qxp-ss-img.dtsi"
@@ -330,3 +331,4 @@ map0 {
#include "imx8qxp-ss-adma.dtsi"
#include "imx8qxp-ss-conn.dtsi"
#include "imx8qxp-ss-lsio.dtsi"
+#include "imx8qxp-ss-hsio.dtsi"