diff mbox series

arm64: dts: rockchip: Enable HDMI0 on rk3588-nanopc-t6

Message ID 20241023080605.623125-1-marcin.juszkiewicz@linaro.org (mailing list archive)
State New
Headers show
Series arm64: dts: rockchip: Enable HDMI0 on rk3588-nanopc-t6 | expand

Commit Message

Marcin Juszkiewicz Oct. 23, 2024, 8:06 a.m. UTC 
Add the necessary DT changes to enable HDMI0 on FriendlyELEC NanoPC-T6.
Tested on LTS variant of the board but this part is the same on both.

Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
---
 .../boot/dts/rockchip/rk3588-nanopc-t6.dtsi   | 47 +++++++++++++++++++
 1 file changed, 47 insertions(+)

Comments

Heiko Stübner Oct. 24, 2024, 8:30 a.m. UTC | #1 
On Wed, 23 Oct 2024 10:06:04 +0200, Marcin Juszkiewicz wrote:
> Add the necessary DT changes to enable HDMI0 on FriendlyELEC NanoPC-T6.
> Tested on LTS variant of the board but this part is the same on both.
> 
> 

Applied, thanks!

[1/1] arm64: dts: rockchip: Enable HDMI0 on rk3588-nanopc-t6
      commit: c3c9cd8f65f7f833de95dd70aa17393afa58f50b

Best regards,
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dtsi
index fc131789b4c3..35d5d9f0c477 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dtsi
@@ -10,6 +10,7 @@ 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
 #include <dt-bindings/usb/pd.h>
 #include "rk3588.dtsi"
 
@@ -40,6 +41,17 @@  chosen {
 		stdout-path = "serial2:1500000n8";
 	};
 
+	hdmi0-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi0_con_in: endpoint {
+				remote-endpoint = <&hdmi0_out_con>;
+			};
+		};
+	};
+
 	ir-receiver {
 		compatible = "gpio-ir-receiver";
 		gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_LOW>;
@@ -318,6 +330,26 @@  &gpu {
 	status = "okay";
 };
 
+&hdmi0 {
+	status = "okay";
+};
+
+&hdmi0_in {
+	hdmi0_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi0>;
+	};
+};
+
+&hdmi0_out {
+	hdmi0_out_con: endpoint {
+		remote-endpoint = <&hdmi0_con_in>;
+	};
+};
+
+&hdptxphy_hdmi0 {
+	status = "okay";
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0m2_xfer>;
@@ -1039,3 +1071,18 @@  &usb_host1_ehci {
 &usb_host1_ohci {
 	status = "okay";
 };
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vop {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi0: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi0_in_vp0>;
+	};
+};