@@ -193,6 +193,7 @@ J721E_IOPAD(0x1c0, PIN_OUTPUT, 1) /* (AA2) SPI0_CS0.UART0_RTSn */
J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
>;
+ bootph-all;
};
main_uart1_pins_default: main-uart1-default-pins {
@@ -234,6 +235,7 @@ J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
J721E_IOPAD(0x25c, PIN_INPUT, 0) /* (R28) MMC1_SDWP */
>;
+ bootph-all;
};
vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-default-pins {
@@ -247,6 +249,7 @@ main_usbss0_pins_default: main-usbss0-default-pins {
J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
>;
+ bootph-all;
};
main_usbss1_pins_default: main-usbss1-default-pins {
@@ -342,6 +345,7 @@ wkup_uart0_pins_default: wkup-uart0-default-pins {
J721E_WKUP_IOPAD(0xa0, PIN_INPUT, 0) /* (J29) WKUP_UART0_RXD */
J721E_WKUP_IOPAD(0xa4, PIN_OUTPUT, 0) /* (J28) WKUP_UART0_TXD */
>;
+ bootph-all;
};
mcu_uart0_pins_default: mcu-uart0-default-pins {
@@ -351,6 +355,7 @@ J721E_WKUP_IOPAD(0xec, PIN_OUTPUT, 0) /* (J27) WKUP_GPIO0_15.MCU_UART0_RTSn */
J721E_WKUP_IOPAD(0xe4, PIN_INPUT, 0) /* (H28) WKUP_GPIO0_13.MCU_UART0_RXD */
J721E_WKUP_IOPAD(0xe0, PIN_OUTPUT, 0) /* (G29) WKUP_GPIO0_12.MCU_UART0_TXD */
>;
+ bootph-all;
};
sw11_button_pins_default: sw11-button-default-pins {
@@ -370,6 +375,7 @@ J721E_WKUP_IOPAD(0x4c, PIN_INPUT, 0) /* (C23) MCU_OSPI1_D3 */
J721E_WKUP_IOPAD(0x3c, PIN_INPUT, 0) /* (B23) MCU_OSPI1_DQS */
J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
>;
+ bootph-all;
};
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
@@ -435,12 +441,14 @@ &wkup_uart0 {
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
};
&mcu_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
+ bootph-all;
};
&main_uart0 {
@@ -449,6 +457,7 @@ &main_uart0 {
pinctrl-0 = <&main_uart0_pins_default>;
/* Shared with ATF on this platform */
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+ bootph-all;
};
&main_uart1 {
@@ -487,6 +496,7 @@ &main_sdhci0 {
/* eMMC */
status = "okay";
non-removable;
+ bootph-all;
ti,driver-strength-ohm = <50>;
disable-wp;
};
@@ -498,12 +508,14 @@ &main_sdhci1 {
vqmmc-supply = <&vdd_sd_dv_alt>;
pinctrl-names = "default";
pinctrl-0 = <&main_mmc1_pins_default>;
+ bootph-all;
ti,driver-strength-ohm = <50>;
disable-wp;
};
&usb_serdes_mux {
idle-states = <1>, <0>; /* USB0 to SERDES3, USB1 to SERDES1 */
+ bootph-all;
};
&serdes_ln_ctrl {
@@ -513,6 +525,7 @@ &serdes_ln_ctrl {
<J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
<J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
<J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
+ bootph-all;
};
&serdes_wiz3 {
@@ -533,6 +546,7 @@ serdes3_usb_link: phy@0 {
&usbss0 {
pinctrl-names = "default";
pinctrl-0 = <&main_usbss0_pins_default>;
+ bootph-all;
ti,vbus-divider;
};
@@ -541,6 +555,7 @@ &usb0 {
maximum-speed = "super-speed";
phys = <&serdes3_usb_link>;
phy-names = "cdns3,usb3-phy";
+ bootph-all;
};
&usbss1 {
@@ -613,6 +628,7 @@ partition@800000 {
partition@3fe0000 {
label = "qspi.phypattern";
reg = <0x3fe0000 0x20000>;
+ bootph-all;
};
};
};
@@ -151,6 +151,7 @@ wkup_i2c0_pins_default: wkup-i2c0-default-pins {
J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
>;
+ bootph-all;
};
pmic_irq_pins_default: pmic-irq-default-pins {
@@ -173,6 +174,7 @@ J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */
J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */
J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */
>;
+ bootph-all;
};
mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-default-pins {
@@ -192,6 +194,7 @@ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* MCU_HYPERBUS0_DQ5 */
J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* MCU_HYPERBUS0_DQ6 */
J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* MCU_HYPERBUS0_DQ7 */
>;
+ bootph-all;
};
};
@@ -422,6 +425,7 @@ partition@800000 {
partition@3fe0000 {
label = "ospi.phypattern";
reg = <0x3fe0000 0x20000>;
+ bootph-all;
};
};
};
@@ -440,6 +444,7 @@ &hbmc {
flash@0,0 {
compatible = "cypress,hyperflash", "cfi-flash";
reg = <0x00 0x00 0x4000000>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";