arm64: dts: ti: k3-am69-sk: Add USB SuperSpeed support

Commit Message

Enric Balletbo i Serra Nov. 26, 2024, 10:08 a.m. UTC

From: Dasnavis Sabiya <[e-mail]>

AM69 SK board has two stacked USB3 connectors:
   1. USB3 (Stacked TypeA + TypeC)
   2. USB3 TypeA Hub interfaced through TUSB8041.

The board uses SERDES0 Lane 3 for USB3 IP. So update the
SerDes lane info for PCIe and USB. Add the pin mux data
and enable USB 3.0 support with its respective SERDES settings.

Signed-off-by: Dasnavis Sabiya <[e-mail]>
Signed-off-by: Enric Balletbo i Serra <[e-mail]>
---
I've been carrying this patch for quite long time in my builds to have
support for USB on my AM69-SK board without problems. For some reason this
patch was never send to upstream or I couldn't find it. So I took the
opportunity, now that I rebased my build, to send upstream.

I have maintained the original author of the downstream patch as is
basically his work.
---
 arch/arm64/boot/dts/ti/k3-am69-sk.dts | 33 +++++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)


---
base-commit: 7eef7e306d3c40a0c5b9ff6adc9b273cc894dbd5
change-id: 20241126-am69sk-dt-usb-89180ef58f8d

Best regards,

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
index 1e36965a14032ca07143230855e04b9549f1d0d1..72797f4b689c1d069bf395d6d4fe1846dc4e4297 100644
--- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
@@ -484,6 +484,12 @@  J784S4_IOPAD(0x09C, PIN_OUTPUT, 0) /* (AF35) MCAN7_TX */
 		>;
 	};
 
+	main_usbss0_pins_default: main-usbss0-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0EC, PIN_OUTPUT, 6) /* (AN37) TIMER_IO1.USB0_DRVVBUS */
+		>;
+	};
+
 };
 
 &wkup_pmx0 {
@@ -1299,6 +1305,14 @@  serdes0_pcie_link: phy@0 {
 		cdns,phy-type = <PHY_TYPE_PCIE>;
 		resets = <&serdes_wiz0 1>, <&serdes_wiz0 2>, <&serdes_wiz0 3>;
 	};
+
+	serdes0_usb_link: phy@3 {
+		reg = <3>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+		resets = <&serdes_wiz0 4>;
+	};
 };
 
 &serdes_wiz1 {
@@ -1339,3 +1353,22 @@  &pcie3_rc {
 	phy-names = "pcie-phy";
 	num-lanes = <1>;
 };
+
+&usb_serdes_mux {
+	idle-states = <0>; /* USB0 to SERDES0 */
+};
+
+&usbss0 {
+	status = "okay";
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	pinctrl-names = "default";
+	ti,vbus-divider;
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+	maximum-speed = "super-speed";
+	phys = <&serdes0_usb_link>;
+	phy-names = "cdns3,usb3-phy";
+};