| Message ID | 20241128-z2-v2-3-76cc59bbf117@gmail.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | Driver for Apple Z2 touchscreens. | expand |
Sasha Finkelstein via B4 Relay 於 2024/11/29 早上6:29 寫道: > From: Sasha Finkelstein <fnkl.kernel@gmail.com> > > Adds device tree entries for the touchbar digitizer > > Co-developed-by: Janne Grunau <j@jannau.net> > Signed-off-by: Janne Grunau <j@jannau.net> > Signed-off-by: Sasha Finkelstein <fnkl.kernel@gmail.com> > --- > arch/arm64/boot/dts/apple/t8103-j293.dts | 26 ++++++++++++++++++++++++++ > arch/arm64/boot/dts/apple/t8103.dtsi | 20 ++++++++++++++++++++ > arch/arm64/boot/dts/apple/t8112-j493.dts | 24 ++++++++++++++++++++++++ > arch/arm64/boot/dts/apple/t8112.dtsi | 14 ++++++++++++++ > 4 files changed, 84 insertions(+) > > diff --git a/arch/arm64/boot/dts/apple/t8103-j293.dts b/arch/arm64/boot/dts/apple/t8103-j293.dts > index 56b0c67bfcda321b60c621de092643017693ff91..c31eb3f6f54268cafc9197a9244a5954fbb42802 100644 > --- a/arch/arm64/boot/dts/apple/t8103-j293.dts > +++ b/arch/arm64/boot/dts/apple/t8103-j293.dts > @@ -17,6 +17,14 @@ / { > compatible = "apple,j293", "apple,t8103", "apple,arm-platform"; > model = "Apple MacBook Pro (13-inch, M1, 2020)"; > > + /* > + * All of those are used by the bootloader to pass calibration > + * blobs and other device-specific properties > + */ > + aliases { > + touchbar0 = &touchbar0; > + }; > + > led-controller { > compatible = "pwm-leds"; > led-0 { > @@ -49,3 +57,21 @@ &i2c4 { > &fpwm1 { > status = "okay"; > }; > + > +&spi0 { > + status = "okay"; > + > + touchbar0: touchbar@0 { > + compatible = "apple,j293-touchbar"; > + reg = <0>; > + spi-max-frequency = <11500000>; > + spi-cs-setup-delay-ns = <2000>; > + spi-cs-hold-delay-ns = <2000>; > + reset-gpios = <&pinctrl_ap 139 GPIO_ACTIVE_LOW>; > + interrupts-extended = <&pinctrl_ap 194 IRQ_TYPE_EDGE_FALLING>; > + firmware-name = "apple/dfrmtfw-j293.bin"; > + touchscreen-size-x = <23045>; > + touchscreen-size-y = <640>; > + touchscreen-inverted-y; > + }; > +}; > diff --git a/arch/arm64/boot/dts/apple/t8103.dtsi b/arch/arm64/boot/dts/apple/t8103.dtsi > index 9b0dad6b618444ac6b1c9735c50cccfc3965f947..9b83341a799d9a37578e5461e6b184f81ee7435c 100644 > --- a/arch/arm64/boot/dts/apple/t8103.dtsi > +++ b/arch/arm64/boot/dts/apple/t8103.dtsi > @@ -326,6 +326,13 @@ clkref: clock-ref { > clock-output-names = "clkref"; > }; > > + clk_200m: clock-200m { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <200000000>; > + clock-output-names = "clk_200m"; > + }; > + > /* > * This is a fabulated representation of the input clock > * to NCO since we don't know the true clock tree. > @@ -441,6 +448,19 @@ fpwm1: pwm@235044000 { > status = "disabled"; > }; > > + spi0: spi@235100000 { > + compatible = "apple,t8103-spi", "apple,spi"; > + reg = <0x2 0x35100000 0x0 0x4000>; > + interrupt-parent = <&aic>; > + interrupts = <AIC_IRQ 614 IRQ_TYPE_LEVEL_HIGH>; > + cs-gpios = <&pinctrl_ap 109 GPIO_ACTIVE_LOW>; > + clocks = <&clk_200m>; > + power-domains = <&ps_spi0>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; /* only used in J293 */ > + }; > + > serial0: serial@235200000 { > compatible = "apple,s5l-uart"; > reg = <0x2 0x35200000 0x0 0x1000>; > diff --git a/arch/arm64/boot/dts/apple/t8112-j493.dts b/arch/arm64/boot/dts/apple/t8112-j493.dts > index 0ad908349f55406783942735a2e9dad54cda00ec..3332cc87cdf1a418c4c2247639baf5d2a42ed3c2 100644 > --- a/arch/arm64/boot/dts/apple/t8112-j493.dts > +++ b/arch/arm64/boot/dts/apple/t8112-j493.dts > @@ -17,8 +17,13 @@ / { > compatible = "apple,j493", "apple,t8112", "apple,arm-platform"; > model = "Apple MacBook Pro (13-inch, M2, 2022)"; > > + /* > + * All of those are used by the bootloader to pass calibration > + * blobs and other device-specific properties > + */ > aliases { > bluetooth0 = &bluetooth0; > + touchbar0 = &touchbar0; > wifi0 = &wifi0; > }; > > @@ -67,3 +72,22 @@ &i2c4 { > &fpwm1 { > status = "okay"; > }; > + > +&spi3 { > + status = "okay"; > + > + touchbar0: touchbar@0 { > + compatible = "apple,j493-touchbar"; > + reg = <0>; > + spi-max-frequency = <8000000>; > + spi-cs-setup-delay-ns = <2000>; > + spi-cs-hold-delay-ns = <2000>; > + Remove the empty line > + reset-gpios = <&pinctrl_ap 170 GPIO_ACTIVE_LOW>; > + interrupts-extended = <&pinctrl_ap 174 IRQ_TYPE_EDGE_FALLING>; > + firmware-name = "apple/dfrmtfw-j493.bin"; > + touchscreen-size-x = <23045>; > + touchscreen-size-y = <640>; > + touchscreen-inverted-y; > + }; > +}; > diff --git a/arch/arm64/boot/dts/apple/t8112.dtsi b/arch/arm64/boot/dts/apple/t8112.dtsi > index 1666e6ab250bc0be9b8318e3c8fc903ccd3f3760..977c1ca5e8c1b566bb3876b6619ea8812b98e072 100644 > --- a/arch/arm64/boot/dts/apple/t8112.dtsi > +++ b/arch/arm64/boot/dts/apple/t8112.dtsi > @@ -467,6 +467,20 @@ fpwm1: pwm@235044000 { > status = "disabled"; > }; > > + spi3: spi@23510c000 { > + compatible = "apple,t8112-spi", "apple,spi"; > + reg = <0x2 0x3510c000 0x0 0x4000>; > + interrupt-parent = <&aic>; > + interrupts = <AIC_IRQ 751 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clkref>; > + pinctrl-0 = <&spi3_pins>; > + pinctrl-names = "default"; > + power-domains = <&ps_spi3>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; /* only used in J493 */ ? > + }; > + > serial0: serial@235200000 { > compatible = "apple,s5l-uart"; > reg = <0x2 0x35200000 0x0 0x1000>; > Nick Chan
diff --git a/arch/arm64/boot/dts/apple/t8103-j293.dts b/arch/arm64/boot/dts/apple/t8103-j293.dts index 56b0c67bfcda321b60c621de092643017693ff91..c31eb3f6f54268cafc9197a9244a5954fbb42802 100644 --- a/arch/arm64/boot/dts/apple/t8103-j293.dts +++ b/arch/arm64/boot/dts/apple/t8103-j293.dts @@ -17,6 +17,14 @@ / { compatible = "apple,j293", "apple,t8103", "apple,arm-platform"; model = "Apple MacBook Pro (13-inch, M1, 2020)"; + /* + * All of those are used by the bootloader to pass calibration + * blobs and other device-specific properties + */ + aliases { + touchbar0 = &touchbar0; + }; + led-controller { compatible = "pwm-leds"; led-0 { @@ -49,3 +57,21 @@ &i2c4 { &fpwm1 { status = "okay"; }; + +&spi0 { + status = "okay"; + + touchbar0: touchbar@0 { + compatible = "apple,j293-touchbar"; + reg = <0>; + spi-max-frequency = <11500000>; + spi-cs-setup-delay-ns = <2000>; + spi-cs-hold-delay-ns = <2000>; + reset-gpios = <&pinctrl_ap 139 GPIO_ACTIVE_LOW>; + interrupts-extended = <&pinctrl_ap 194 IRQ_TYPE_EDGE_FALLING>; + firmware-name = "apple/dfrmtfw-j293.bin"; + touchscreen-size-x = <23045>; + touchscreen-size-y = <640>; + touchscreen-inverted-y; + }; +}; diff --git a/arch/arm64/boot/dts/apple/t8103.dtsi b/arch/arm64/boot/dts/apple/t8103.dtsi index 9b0dad6b618444ac6b1c9735c50cccfc3965f947..9b83341a799d9a37578e5461e6b184f81ee7435c 100644 --- a/arch/arm64/boot/dts/apple/t8103.dtsi +++ b/arch/arm64/boot/dts/apple/t8103.dtsi @@ -326,6 +326,13 @@ clkref: clock-ref { clock-output-names = "clkref"; }; + clk_200m: clock-200m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <200000000>; + clock-output-names = "clk_200m"; + }; + /* * This is a fabulated representation of the input clock * to NCO since we don't know the true clock tree. @@ -441,6 +448,19 @@ fpwm1: pwm@235044000 { status = "disabled"; }; + spi0: spi@235100000 { + compatible = "apple,t8103-spi", "apple,spi"; + reg = <0x2 0x35100000 0x0 0x4000>; + interrupt-parent = <&aic>; + interrupts = <AIC_IRQ 614 IRQ_TYPE_LEVEL_HIGH>; + cs-gpios = <&pinctrl_ap 109 GPIO_ACTIVE_LOW>; + clocks = <&clk_200m>; + power-domains = <&ps_spi0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; /* only used in J293 */ + }; + serial0: serial@235200000 { compatible = "apple,s5l-uart"; reg = <0x2 0x35200000 0x0 0x1000>; diff --git a/arch/arm64/boot/dts/apple/t8112-j493.dts b/arch/arm64/boot/dts/apple/t8112-j493.dts index 0ad908349f55406783942735a2e9dad54cda00ec..3332cc87cdf1a418c4c2247639baf5d2a42ed3c2 100644 --- a/arch/arm64/boot/dts/apple/t8112-j493.dts +++ b/arch/arm64/boot/dts/apple/t8112-j493.dts @@ -17,8 +17,13 @@ / { compatible = "apple,j493", "apple,t8112", "apple,arm-platform"; model = "Apple MacBook Pro (13-inch, M2, 2022)"; + /* + * All of those are used by the bootloader to pass calibration + * blobs and other device-specific properties + */ aliases { bluetooth0 = &bluetooth0; + touchbar0 = &touchbar0; wifi0 = &wifi0; }; @@ -67,3 +72,22 @@ &i2c4 { &fpwm1 { status = "okay"; }; + +&spi3 { + status = "okay"; + + touchbar0: touchbar@0 { + compatible = "apple,j493-touchbar"; + reg = <0>; + spi-max-frequency = <8000000>; + spi-cs-setup-delay-ns = <2000>; + spi-cs-hold-delay-ns = <2000>; + + reset-gpios = <&pinctrl_ap 170 GPIO_ACTIVE_LOW>; + interrupts-extended = <&pinctrl_ap 174 IRQ_TYPE_EDGE_FALLING>; + firmware-name = "apple/dfrmtfw-j493.bin"; + touchscreen-size-x = <23045>; + touchscreen-size-y = <640>; + touchscreen-inverted-y; + }; +}; diff --git a/arch/arm64/boot/dts/apple/t8112.dtsi b/arch/arm64/boot/dts/apple/t8112.dtsi index 1666e6ab250bc0be9b8318e3c8fc903ccd3f3760..977c1ca5e8c1b566bb3876b6619ea8812b98e072 100644 --- a/arch/arm64/boot/dts/apple/t8112.dtsi +++ b/arch/arm64/boot/dts/apple/t8112.dtsi @@ -467,6 +467,20 @@ fpwm1: pwm@235044000 { status = "disabled"; }; + spi3: spi@23510c000 { + compatible = "apple,t8112-spi", "apple,spi"; + reg = <0x2 0x3510c000 0x0 0x4000>; + interrupt-parent = <&aic>; + interrupts = <AIC_IRQ 751 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clkref>; + pinctrl-0 = <&spi3_pins>; + pinctrl-names = "default"; + power-domains = <&ps_spi3>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + serial0: serial@235200000 { compatible = "apple,s5l-uart"; reg = <0x2 0x35200000 0x0 0x1000>;