diff mbox series

[7/8] arm64: dts: allwinner: rg35xx: Enable LCD output

Message ID 20250216092827.15444-8-ryan@testtoast.com (mailing list archive)
State New
Headers show
Series arm64: dts: allwinner: h616: add LCD timing controller and display engine support | expand

Commit Message

Ryan Walklin Feb. 16, 2025, 9:27 a.m. UTC 
The RG35XX has a 640x480 RGB/SPI LCD panel, supported by the SoC display
pipeline and an NV3052C controller. The H616 SOC's GPIO bank D contains
the muxed display pins for RGB and LVDS output support.

Enable the display engine and LCD timing controller, configure the
panel, and add a fixed 3.3v GPIO-controlled regulator for the panel, and
a VCC supply for the display pins as per the other GPIO banks.

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
---
 .../sun50i-h700-anbernic-rg35xx-2024.dts      | 58 +++++++++++++++++++
 1 file changed, 58 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
index a231abf1684ad..388487d4720e2 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
@@ -175,6 +175,49 @@  reg_vcc5v: regulator-vcc5v { /* USB-C power input */
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 	};
+
+	reg_lcd: regulator-gpio-lcd-vdd {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "vdd-lcd";
+		gpio = <&pio 8 15 GPIO_ACTIVE_HIGH>; // PI15
+		enable-active-high;
+	};
+
+	spi_lcd: spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&pio 8 9 GPIO_ACTIVE_HIGH>; // PI9
+		mosi-gpios = <&pio 8 10 GPIO_ACTIVE_HIGH>; // PI10
+		cs-gpios = <&pio 8 8 GPIO_ACTIVE_HIGH>; // PI8
+		num-chipselects = <1>;
+
+		panel: panel@0 {
+			compatible = "anbernic,rg35xx-plus-panel";
+
+			reg = <0>;
+
+			spi-max-frequency = <3125000>;
+			spi-3wire;
+
+			reset-gpios = <&pio 8 14 GPIO_ACTIVE_LOW>; // PI14
+
+			backlight = <&backlight>;
+			power-supply = <&reg_lcd>;
+
+			pinctrl-0 = <&lcd0_rgb888_pins>;
+			pinctrl-names = "default";
+
+			port {
+				panel_in_rgb: endpoint {
+					remote-endpoint = <&tcon_lcd0_out_lcd>;
+				};
+			};
+		};
+	};
 };
 
 &codec {
@@ -187,6 +230,10 @@  &cpu0 {
 	cpu-supply = <&reg_dcdc1>;
 };
 
+&de {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -206,6 +253,7 @@  &ohci0 {
 &pio {
 	vcc-pa-supply = <&reg_cldo3>;
 	vcc-pc-supply = <&reg_cldo3>;
+	vcc-pd-supply = <&reg_cldo3>;
 	vcc-pe-supply = <&reg_cldo3>;
 	vcc-pf-supply = <&reg_cldo3>;
 	vcc-pg-supply = <&reg_aldo4>;
@@ -355,3 +403,13 @@  &usbotg {
 &usbphy {
 	status = "okay";
 };
+
+&tcon_lcd0 {
+	status = "okay";
+};
+
+&tcon_lcd0_out {
+	tcon_lcd0_out_lcd: endpoint@1 {
+		remote-endpoint = <&panel_in_rgb>;
+	};
+};