| Message ID | 20250220165051.1889055-1-wens@kernel.org (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | arm64: dts: rockchip: rock-3a: Remove bluetooth node | expand |
Hi, What about adding another patch that converts it to a dtso? Best regards, Shengyu 在 2025/2/21 0:50, Chen-Yu Tsai 写道: > From: Chen-Yu Tsai <wens@csie.org> > > The Bluetooth node described in the device tree is actually on an M.2 > slot. What module is present depends on what the end user installed, > and should be left to an overlay. > > Remove the existing bluetooth node. This gets rid of bogus timeout > errors. > > Fixes: 8cf890aabd45 ("arm64: dts: rockchip: Add nodes for SDIO/UART Wi-Fi/Bluetooth modules to Radxa Rock 3A") > Signed-off-by: Chen-Yu Tsai <wens@csie.org> > --- > arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts | 14 -------------- > 1 file changed, 14 deletions(-) > > diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts > index ac79140a9ecd..44cfdfeed668 100644 > --- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts > +++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts > @@ -778,20 +778,6 @@ &uart1 { > pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>; > uart-has-rtscts; > status = "okay"; > - > - bluetooth { > - compatible = "brcm,bcm43438-bt"; > - clocks = <&rk809 1>; > - clock-names = "lpo"; > - device-wakeup-gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>; > - host-wakeup-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>; > - shutdown-gpios = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>; > - pinctrl-names = "default"; > - pinctrl-0 = <&bt_host_wake &bt_wake &bt_enable>; > - vbat-supply = <&vcc3v3_sys>; > - vddio-supply = <&vcc_1v8>; > - /* vddio comes from regulator on module, use IO bank voltage instead */ > - }; > }; > > &uart2 {
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts index ac79140a9ecd..44cfdfeed668 100644 --- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts +++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts @@ -778,20 +778,6 @@ &uart1 { pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>; uart-has-rtscts; status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - clocks = <&rk809 1>; - clock-names = "lpo"; - device-wakeup-gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>; - host-wakeup-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>; - shutdown-gpios = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&bt_host_wake &bt_wake &bt_enable>; - vbat-supply = <&vcc3v3_sys>; - vddio-supply = <&vcc_1v8>; - /* vddio comes from regulator on module, use IO bank voltage instead */ - }; }; &uart2 {