@@ -50,6 +50,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-lenovo-hr630.dtb \
aspeed-bmc-lenovo-hr855xg2.dtb \
aspeed-bmc-microsoft-olympus.dtb \
+ aspeed-bmc-nvidia-gb200nvl-bmc.dtb \
aspeed-bmc-opp-lanyang.dtb \
aspeed-bmc-opp-mowgli.dtb \
aspeed-bmc-opp-nicole.dtb \
new file mode 100644
@@ -0,0 +1,1229 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "AST2600 GB200NVL BMC";
+ compatible = "nvidia,gb200nvl-bmc", "aspeed,ast2600";
+
+ aliases {
+ serial2 = &uart3;
+ serial4 = &uart5;
+ i2c16 = &imux16;
+ i2c17 = &imux17;
+ i2c18 = &imux18;
+ i2c19 = &imux19;
+ i2c20 = &imux20;
+ i2c21 = &imux21;
+ i2c22 = &imux22;
+ i2c23 = &imux23;
+ i2c24 = &imux24;
+ i2c25 = &imux25;
+ i2c26 = &imux26;
+ i2c27 = &imux27;
+ i2c28 = &imux28;
+ i2c29 = &imux29;
+ i2c30 = &imux30;
+ i2c31 = &imux31;
+ i2c32 = &imux32;
+ i2c33 = &imux33;
+ i2c34 = &imux34;
+ i2c35 = &imux35;
+ i2c36 = &imux36;
+ i2c37 = &imux37;
+ i2c38 = &imux38;
+ i2c39 = &imux39;
+ i2c40 = &e1si2c0;
+ i2c41 = &e1si2c1;
+ i2c42 = &e1si2c2;
+ i2c43 = &e1si2c3;
+ i2c44 = &e1si2c4;
+ i2c45 = &e1si2c5;
+ i2c46 = &e1si2c6;
+ i2c47 = &e1si2c7;
+ i2c48 = &i2c17mux0;
+ i2c49 = &i2c17mux1;
+ i2c50 = &i2c17mux2;
+ i2c51 = &i2c17mux3;
+ i2c52 = &i2c25mux0;
+ i2c53 = &i2c25mux1;
+ i2c54 = &i2c25mux2;
+ i2c55 = &i2c25mux3;
+ i2c56 = &i2c29mux0;
+ i2c57 = &i2c29mux1;
+ i2c58 = &i2c29mux2;
+ i2c59 = &i2c29mux3;
+ };
+
+ chosen {
+ stdout-path = &uart5;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x80000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ vga_memory: framebuffer@9f000000 {
+ no-map;
+ reg = <0x9f000000 0x01000000>; /* 16M */
+ };
+
+ ramoops@a0000000 {
+ compatible = "ramoops";
+ reg = <0xa0000000 0x100000>; /* 1MB */
+ record-size = <0x10000>; /* 64KB */
+ max-reason = <2>; /* KMSG_DUMP_OOPS */
+ };
+
+ gfx_memory: framebuffer {
+ size = <0x01000000>;
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+
+ video_engine_memory: jpegbuffer {
+ size = <0x02000000>; /* 32M */
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-0{
+ label = "uid_led";
+ gpios = <&sgpiom0 27 GPIO_ACTIVE_LOW>;
+ };
+ led-1{
+ label = "fault_led";
+ gpios = <&sgpiom0 29 GPIO_ACTIVE_LOW>;
+ };
+ led-2{
+ label = "power_led";
+ gpios = <&sgpiom0 31 GPIO_ACTIVE_LOW>;
+ };
+
+ };
+
+ buttons {
+ button-power {
+ label = "power-btn";
+ gpio = <&sgpiom0 156 GPIO_ACTIVE_LOW>;
+ };
+ button-uid {
+ label = "uid-btn";
+ gpio = <&sgpiom0 154 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+};
+
+// Enable Primary flash on FMC for bring up activity
+&fmc {
+ status = "okay";
+ flash@0 {
+ status = "okay";
+ compatible = "jedec,spi-nor";
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ u-boot@0 {
+ // 896KB
+ reg = <0x0 0xe0000>;
+ label = "u-boot";
+ };
+
+ kernel@100000 {
+ // 9MB
+ reg = <0x100000 0x900000>;
+ label = "kernel";
+ };
+
+ rofs@a00000 {
+ // 55292KB (extends to end of 64MB SPI - 4KB)
+ reg = <0xa00000 0x35FF000>;
+ label = "rofs";
+ };
+ };
+ };
+};
+
+&spi2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi2_default>;
+
+ // Data SPI is 64MB in size
+ flash@0 {
+ status = "okay";
+ label = "config";
+ spi-max-frequency = <50000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ u-boot-env@0 {
+ // 256KB
+ reg = <0x0 0x40000>;
+ label = "u-boot-env";
+ };
+
+ rwfs@40000 {
+ // 16MB
+ reg = <0x40000 0x1000000>;
+ label = "rwfs";
+ };
+
+ log@1040000 {
+ // 40MB
+ reg = <0x1040000 0x2800000>;
+ label = "log";
+ };
+ };
+ };
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart3 {
+ // Enabling SOL
+ status = "okay";
+};
+
+&uart5 {
+ // BMC Debug Console
+ status = "okay";
+};
+
+&uart_routing {
+ status = "okay";
+};
+
+// MAC1 (per schematics, 1-based MAC1-MAC4) of AST2600 connected to external PHY
+// This is "mac0" in zero-based DTS
+&mdio0 {
+ status = "okay";
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+};
+
+&mdio3 {
+ status = "okay";
+ ethphy3: ethernet-phy@2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+ };
+};
+
+&mac0 {
+ status = "okay";
+ pinctrl-names = "default";
+ phy-mode = "rgmii";
+ phy-handle = <ðphy3>;
+ pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&mac2 {
+ status = "okay";
+ phy-mode = "rmii";
+ use-ncsi;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii3_default>;
+};
+
+// Enable emmc
+&emmc_controller {
+ status = "okay";
+};
+
+&emmc {
+ non-removable;
+ pinctrl-0 = <&pinctrl_emmcg5_default>;
+ bus-width = <4>;
+ max-frequency = <52000000>;
+ clk-phase-mmc-hs200 = <9>, <225>;
+};
+
+/*
+ * Enable USB port A as device (via the virtual hub) to host
+ */
+&vhub {
+ status = "okay";
+ pinctrl-names = "default";
+ /*
+ * Uncomment below line to enable internal EHCI controller
+ * Current config uses xHCI Port1
+ */
+};
+
+&video {
+ status = "okay";
+ memory-region = <&video_engine_memory>;
+};
+
+// USB 2.0 to HMC, on USB Port B
+&ehci1 {
+ status = "okay";
+};
+
+// USB 1.0
+&uhci {
+ status = "okay";
+};
+
+&sgpiom0 {
+ status="okay";
+ ngpios = <128>;
+
+ gpio-line-names =
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "RUN_POWER_FAULT_L-I","SYS_RST_IN_L-O",
+ "RUN_POWER_PG-I","PWR_BRAKE_L-O",
+ "SYS_RST_OUT_L-I","RUN_POWER_EN-O",
+ "L0L1_RST_REQ_OUT_L-I","SHDN_FORCE_L-O",
+ "L2_RST_REQ_OUT_L-I","SHDN_REQ_L-O",
+ "SHDN_OK_L-I","UID_LED_N-O",
+ "BMC_I2C1_FPGA_ALERT_L-I","SYS_FAULT_LED_N-O",
+ "BMC_I2C0_FPGA_ALERT_L-I","PWR_LED_N-O",
+ "FPGA_RSVD_FFU3-I","",
+ "FPGA_RSVD_FFU2-I","",
+ "FPGA_RSVD_FFU1-I","",
+ "FPGA_RSVD_FFU0-I","BMC_I2C_SSIF_ALERT_L-O",
+ "CPU_BOOT_DONE-I","JTAG_MUX_SELECT-O",
+ "SPI_BMC_FPGA_INT_L-I","RTC_CLR_L-O",
+ "THERM_BB_WARN_L-I","UART_MUX_SEL-O",
+ "THERM_BB_OVERT_L-I","",
+ "CPU0_UPHY3_PRSNT1_L-I","IOBRD0_RUN_POWER_EN-O",
+ "CPU0_UPHY3_PRSNT0_L-I","IOBRD1_RUN_POWER_EN-O",
+ "CPU0_UPHY2_PRSNT1_L-I","FPGA_RSVD_FFU4-O",
+ "CPU0_UPHY2_PRSNT0_L-I","FPGA_RSVD_FFU5-O",
+ "CPU0_UPHY1_PRSNT1_L-I","FPGA_RSVD_FFU6-O",
+ "CPU0_UPHY1_PRSNT0_L-I","FPGA_RSVD_FFU7-O",
+ "CPU0_UPHY0_PRSNT1_L-I","RSVD_NV_PLT_DETECT-O",
+ "CPU0_UPHY0_PRSNT0_L-I","SPI1_INT_L-O",
+ "CPU1_UPHY3_PRSNT1_L-I","",
+ "CPU1_UPHY3_PRSNT0_L-I","HMC_EROT_MUX_STATUS",
+ "CPU1_UPHY2_PRSNT1_L-I","",
+ "CPU1_UPHY2_PRSNT0_L-I","",
+ "CPU1_UPHY1_PRSNT1_L-I","",
+ "CPU1_UPHY1_PRSNT0_L-I","",
+ "CPU1_UPHY0_PRSNT1_L-I","",
+ "CPU1_UPHY0_PRSNT0_L-I","",
+ "FAN1_PRESENT_L-I","",
+ "FAN0_PRESENT_L-I","",
+ "","",
+ "IPEX_CABLE_PRSNT_L-I","",
+ "M2_1_PRSNT_L-I","",
+ "M2_0_PRSNT_L-I","",
+ "CPU1_UPHY4_PRSNT1_L-I","",
+ "CPU0_UPHY4_PRSNT0_L-I","",
+ "","",
+ "I2C_RTC_ALERT_L-I","",
+ "FAN7_PRESENT_L-I","",
+ "FAN6_PRESENT_L-I","",
+ "FAN5_PRESENT_L-I","",
+ "FAN4_PRESENT_L-I","",
+ "FAN3_PRESENT_L-I","",
+ "FAN2_PRESENT_L-I","",
+ "IOBRD0_IOX_INT_L-I","",
+ "IOBRD1_PRSNT_L-I","",
+ "IOBRD0_PRSNT_L-I","",
+ "IOBRD1_PWR_GOOD-I","",
+ "IOBRD0_PWR_GOOD-I","",
+ "","",
+ "","",
+ "FAN_FAIL_IN_L-I","",
+ "","",
+ "","",
+ "","",
+ "PDB_CABLE_PRESENT_L-I","",
+ "","",
+ "CHASSIS_PWR_BRK_L-I","",
+ "","",
+ "IOBRD1_IOX_INT_L-I","",
+ "10GBE_SMBALRT_L-I","",
+ "PCIE_WAKE_L-I","",
+ "I2C_M21_ALERT_L-I","",
+ "I2C_M20_ALERT_L-I","",
+ "TRAY_FAST_SHDN_L-I","",
+ "UID_BTN_N-I","",
+ "PWR_BTN_L-I","",
+ "PSU_SMB_ALERT_L-I","",
+ "","",
+ "","",
+ "NODE_LOC_ID[0]-I","",
+ "NODE_LOC_ID[1]-I","",
+ "NODE_LOC_ID[2]-I","",
+ "NODE_LOC_ID[3]-I","",
+ "NODE_LOC_ID[4]-I","",
+ "NODE_LOC_ID[5]-I","",
+ "FAN10_PRESENT_L-I","",
+ "FAN9_PRESENT_L-I","",
+ "FAN8_PRESENT_L-I","",
+ "FPGA1_READY_HMC-I","",
+ "DP_HPD-I","",
+ "HMC_I2C3_FPGA_ALERT_L-I","",
+ "HMC_I2C2_FPGA_ALERT_L-I","",
+ "FPGA0_READY_HMC-I","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "LEAK_DETECT_ALERT_L-I","",
+ "MOD1_B2B_CABLE_PRESENT_L-I","",
+ "MOD1_CLINK_CABLE_PRESENT_L-I","",
+ "FAN11_PRESENT_L-I","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "RSVD_SGPIO_IN_CRC[0]","RSVD_SGPIO_O_CRC[7]",
+ "RSVD_SGPIO_IN_CRC[1]","RSVD_SGPIO_O_CRC[6]",
+ "RSVD_SGPIO_IN_CRC[2]","RSVD_SGPIO_O_CRC[5]",
+ "RSVD_SGPIO_IN_CRC[3]","RSVD_SGPIO_O_CRC[4]",
+ "RSVD_SGPIO_IN_CRC[4]","RSVD_SGPIO_O_CRC[3]",
+ "RSVD_SGPIO_IN_CRC[5]","RSVD_SGPIO_O_CRC[2]",
+ "RSVD_SGPIO_IN_CRC[6]","RSVD_SGPIO_O_CRC[1]",
+ "RSVD_SGPIO_IN_CRC[7]","RSVD_SGPIO_O_CRC[0]";
+};
+
+// I2C1, SSIF IPMI interface
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+ disable-master = <1>;
+ i2c-scl-clk-low-timeout-us = <32000>;
+ ssif-bmc@10 {
+ compatible = "ssif-bmc";
+ reg = <0x10>;
+ };
+};
+
+// I2C2
+// BMC_I2C1_FPGA - Secondary FPGA
+// HMC EROT
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+ multi-master;
+ i2c-scl-clk-low-timeout-us = <32000>;
+};
+
+// I2C3
+// BMC_I2C0_FPGA - Primary FPGA
+// HMC FRU EEPROM
+&i2c2 {
+ status = "okay";
+ clock-frequency = <400000>;
+ multi-master;
+ i2c-scl-clk-low-timeout-us = <32000>;
+};
+
+// I2C4
+&i2c3 {
+ status = "disabled";
+};
+
+// I2C5
+// RTC Driver
+// IO Expander
+&i2c4 {
+ status = "okay";
+ clock-frequency = <400000>;
+ // Module 0, Expander @0x21
+ exp4: pca9555@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+
+ gpio-line-names =
+ "RTC_MUX_SEL-O",
+ "PCI_MUX_SEL-O",
+ "TPM_MUX_SEL-O",
+ "FAN_MUX-SEL-O",
+ "SGMII_MUX_SEL-O",
+ "DP_MUX_SEL-O",
+ "UPHY3_USB_SEL-O",
+ "NCSI_MUX_SEL-O",
+ "BMC_PHY_RST-O",
+ "RTC_CLR_L-O",
+ "BMC_12V_CTRL-O",
+ "PS_RUN_IO0_PG-I",
+ "",
+ "",
+ "",
+ "";
+ };
+};
+
+// I2C6
+// Module 0/1 I2C MUX x3
+&i2c5 {
+ status = "okay";
+ clock-frequency = <400000>;
+ multi-master;
+ i2c-scl-clk-low-timeout-us = <32000>;
+
+ i2c-switch@71 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x71>;
+ i2c-mux-idle-disconnect;
+
+ imux16: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux17: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ i2c-switch@74 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c-mux-idle-disconnect;
+
+ i2c17mux0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c17mux1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c17mux2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c17mux3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+ };
+
+ imux18: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux19: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-switch@72 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72>;
+ i2c-mux-idle-disconnect;
+
+ imux20: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux21: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ pca9555@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-line-names =
+ "RST_CX_0_L-O",
+ "RST_CX_1_L-O",
+ "CX0_SSD0_PRSNT_L-I",
+ "CX1_SSD1_PRSNT_L-I",
+ "CX_BOOT_CMPLT_CX0-I",
+ "CX_BOOT_CMPLT_CX1-I",
+ "CX_TWARN_CX0_L-I",
+ "CX_TWARN_CX1_L-I",
+ "CX_OVT_SHDN_CX0-I",
+ "CX_OVT_SHDN_CX1-I",
+ "FNP_L_CX0-O",
+ "FNP_L_CX1-O",
+ "",
+ "MCU_GPIO-I",
+ "MCU_RST_N-O",
+ "MCU_RECOVERY_N-O";
+ };
+ };
+
+ imux22: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux23: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-switch@73 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x73>;
+ i2c-mux-idle-disconnect;
+
+ imux24: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux25: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ i2c-switch@70 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ i2c-mux-idle-disconnect;
+
+ i2c25mux0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c25mux1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c25mux2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c25mux3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+ };
+
+ imux26: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux27: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-switch@75 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2c-mux-idle-disconnect;
+
+ imux28: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux29: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ i2c-switch@74 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c-mux-idle-disconnect;
+
+ i2c29mux0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c29mux1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c29mux2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c29mux3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+ };
+
+ imux30: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux31: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-switch@76 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux32: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux33: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ pca9555@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-line-names =
+ "SEC_RST_CX_0_L-O",
+ "SEC_RST_CX_1_L-O",
+ "SEC_CX0_SSD0_PRSNT_L-I",
+ "SEC_CX1_SSD1_PRSNT_L-I",
+ "SEC_CX_BOOT_CMPLT_CX0-I",
+ "SEC_CX_BOOT_CMPLT_CX1-I",
+ "SEC_CX_TWARN_CX0_L-I",
+ "SEC_CX_TWARN_CX1_L-I",
+ "SEC_CX_OVT_SHDN_CX0-I",
+ "SEC_CX_OVT_SHDN_CX1-I",
+ "SEC_FNP_L_CX0-O",
+ "SEC_FNP_L_CX1-O",
+ "",
+ "SEC_MCU_GPIO-I",
+ "SEC_MCU_RST_N-O",
+ "SEC_MCU_RECOVERY_N-O";
+ };
+ };
+
+ imux34: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux35: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-switch@77 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x77>;
+ i2c-mux-idle-disconnect;
+
+ imux36: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux37: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux38: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux39: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+// I2C7
+// Module 0/1 Leak Sensors
+// Module 0/1 Fan Controllers
+&i2c6 {
+ status = "okay";
+ clock-frequency = <400000>;
+ hsc@12 {
+ compatible = "ti,lm5066i";
+ reg = <0x12>;
+ shunt-resistor-micro-ohms = <190>;
+ status = "okay";
+ };
+ hsc@14 {
+ compatible = "ti,lm5066i";
+ reg = <0x14>;
+ shunt-resistor-micro-ohms = <190>;
+ status = "okay";
+ };
+ max31790@20 {
+ compatible = "maxim,max31790";
+ reg = <0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ max31790@23 {
+ compatible = "maxim,max31790";
+ reg = <0x23>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ max31790@2c {
+ compatible = "maxim,max31790";
+ reg = <0x2c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ max31790@2f {
+ compatible = "maxim,max31790";
+ reg = <0x2f>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+// I2C9
+// M.2
+&i2c8 {
+ status = "okay";
+ clock-frequency = <400000>;
+ multi-master;
+ i2c-scl-clk-low-timeout-us = <32000>;
+};
+
+// I2C10
+// HMC IO Expander
+// Module 0/1 IO Expanders
+&i2c9 {
+ status = "okay";
+ clock-frequency = <400000>;
+ // Module 0, Expander @0x20
+ exp0: pca9555@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+
+ gpio-line-names =
+ "FPGA_THERM_OVERT_L-I",
+ "FPGA_READY_BMC-I",
+ "HMC_BMC_DETECT-O",
+ "HMC_PGOOD-O",
+ "",
+ "BMC_STBY_CYCLE-O",
+ "FPGA_EROT_FATAL_ERROR_L-I",
+ "WP_HW_EXT_CTRL_L-O",
+ "EROT_FPGA_RST_L-O",
+ "FPGA_EROT_RECOVERY_L-O",
+ "BMC_EROT_FPGA_SPI_MUX_SEL-O",
+ "USB_HUB_RESET_L-O",
+ "NCSI_CS1_SEL-O",
+ "SGPIO_EN_L-O",
+ "B2B_IOEXP_INT_L-I",
+ "I2C_BUS_MUX_RESET_L-O";
+ };
+
+ // Module 1, Expander @0x21
+ exp1: pca9555@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+
+ gpio-line-names =
+ "SEC_FPGA_THERM_OVERT_L-I",
+ "SEC_FPGA_READY_BMC-I",
+ "",
+ "",
+ "",
+ "",
+ "SEC_FPGA_EROT_FATAL_ERROR_L-I",
+ "SEC_WP_HW_EXT_CTRL_L-O",
+ "SEC_EROT_FPGA_RST_L-O",
+ "SEC_FPGA_EROT_RECOVERY_L-O",
+ "SEC_BMC_EROT_FPGA_SPI_MUX_SEL-O",
+ "SEC_USB2_HUB_RST_L-O",
+ "",
+ "",
+ "",
+ "SEC_I2C_BUS_MUX_RESET_L-O";
+ };
+
+ // HMC Expander @0x27
+ exp2: pca9555@27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+
+ gpio-line-names =
+ "HMC_PRSNT_L-I",
+ "HMC_READY-I",
+ "HMC_EROT_FATAL_ERROR_L-I",
+ "I2C_MUX_SEL-O",
+ "HMC_EROT_SPI_MUX_SEL-O",
+ "HMC_EROT_RECOVERY_L-O",
+ "HMC_EROT_RST_L-O",
+ "GLOBAL_WP_HMC-O",
+ "FPGA_RST_L-O",
+ "USB2_HUB_RST-O",
+ "CPU_UART_MUX_SEL-O",
+ "",
+ "",
+ "",
+ "",
+ "";
+ };
+ // HMC Expander @0x74
+ exp3: pca9555@74 {
+ compatible = "nxp,pca9555";
+ reg = <0x74>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+
+ gpio-line-names =
+ "IOB_PRSNT_L",
+ "IOB_DP_HPD",
+ "IOX_BMC_RESET",
+ "IOB_IOEXP_INT_L",
+ "IOB_UID_LED_L",
+ "IOB_UID_BTN_L",
+ "IOB_SYS_RST_BTN_L",
+ "IOB_PWR_LED_L",
+ "IOB_PWR_BTN_L",
+ "IOB_PHY_RST",
+ "CPLD_JTAG_MUX_SEL",
+ "",
+ "",
+ "",
+ "",
+ "";
+ };
+};
+
+// I2C11
+// BMC FRU EEPROM
+// BMC Temp Sensor
+&i2c10 {
+ status = "okay";
+ clock-frequency = <400000>;
+ // BMC FRU EEPROM - 256 bytes
+ eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <8>;
+ };
+};
+
+// I2C12
+&i2c11 {
+ status = "disabled";
+};
+
+// I2C13
+&i2c12 {
+ status = "disabled";
+};
+
+// I2C14
+// Module 0 UPHY3 SMBus
+&i2c13 {
+ status = "disabled";
+};
+
+// I2C15
+// Module 1 UPHY3 SMBus
+&i2c14 {
+ status = "okay";
+ clock-frequency = <100000>;
+ multi-master;
+ i2c-scl-clk-low-timeout-us = <32000>;
+
+ //E1.S drive slot 0-3
+ i2c-switch@77 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x77>;
+ i2c-mux-idle-disconnect;
+
+ e1si2c0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ e1si2c1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ e1si2c2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ e1si2c3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+// I2C16
+&i2c15 {
+ status = "okay";
+ clock-frequency = <100000>;
+ multi-master;
+ i2c-scl-clk-low-timeout-us = <32000>;
+
+ //E1.S drive slot 4-7
+ i2c-switch@77 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x77>;
+ i2c-mux-idle-disconnect;
+
+ e1si2c4: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ e1si2c5: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ e1si2c6: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ e1si2c7: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&rng {
+ status = "okay";
+};
+
+&gpio0 {
+ gpio-line-names =
+
+ /* gpio-line-names are the combination of <signal>-<I/O> , "" is
+ * the placeholder for the unused pins
+ */
+
+ /* 208 (26*8) 3.3V GPIOs */
+
+ /*A0-A7*/ "", "", "", "", "", "", "", "",
+ /*B0-B7*/ "", "", "", "", "", "", "", "",
+ /*C0-C7*/ "SGPIO_I2C_MUX_SEL-O", "", "", "", "", "", "", "",
+ /*D0-D7*/ "", "", "", "UART1_MUX_SEL-O", "", "FPGA_PEX_RST_L-O", "", "",
+ /*E0-E7*/
+ "RTL8221_PHY_RST_L-O",
+ "RTL8211_PHY_INT_L-I",
+ "",
+ "UART3_MUX_SEL-O",
+ "", "", "",
+ "SGPIO_BMC_EN-O",
+ /*F0-F7*/ "", "", "", "", "", "", "", "",
+ /*G0-G7*/ "", "", "", "", "", "", "", "",
+ /*H0-H7*/ "", "", "", "", "", "", "", "",
+ /*I0-I7*/ "", "", "", "", "", "QSPI2_RST_L-O", "GLOBAL_WP_BMC-O", "BMC_DDR4_TEN-O",
+ /*J0-J7*/ "", "", "", "", "", "", "", "",
+ /*K0-K7*/ "", "", "", "", "", "", "", "",
+ /*L0-L7*/ "", "", "", "", "", "", "", "",
+ /*M0-M7*/
+ "PCIE_EP_RST_EN-O",
+ "BMC_FRU_WP-O",
+ "HMC_RESET_L-O",
+ "STBY_POWER_EN-O",
+ "STBY_POWER_PG-I",
+ "PCIE_EP_RST_L-O",
+ "", "",
+ /*N0-N7*/ "", "", "", "", "", "", "", "",
+ /*O0-O7*/ "", "", "", "", "", "", "", "",
+ /*P0-P7*/ "", "", "", "", "", "", "", "",
+ /*Q0-Q7*/ "", "", "", "", "", "", "", "",
+ /*R0-R7*/ "", "", "", "", "", "", "", "",
+ /*S0-S7*/ "", "", "", "", "", "", "", "",
+ /*T0-T7*/ "", "", "", "", "", "", "", "",
+ /*U0-U7*/ "", "", "", "", "", "", "", "",
+ /*V0-V7*/ "AP_EROT_REQ-O", "EROT_AP_GNT-I", "", "","PCB_TEMP_ALERT-I", "","", "",
+ /*W0-W7*/ "", "", "", "", "", "", "", "",
+ /*X0-X7*/ "", "", "TPM_MUX_SEL-O", "", "", "", "", "",
+ /*Y0-Y7*/ "", "", "", "EMMC_RST-O", "","", "", "",
+ /*Z0-Z7*/ "BMC_READY-O","", "", "", "", "", "", "";
+};
+
+&gpio1 {
+ /* 36 1.8V GPIOs */
+ gpio-line-names =
+ /*A0-A7*/ "", "", "", "", "", "", "", "",
+ /*B0-B7*/ "", "", "", "", "", "", "IO_EXPANDER_INT_L-I","",
+ /*C0-C7*/ "", "", "", "", "", "", "", "",
+ /*D0-D7*/ "", "", "", "", "", "", "SPI_HOST_TPM_RST_L-O", "SPI_BMC_FPGA_INT_L-I",
+ /*E0-E7*/ "", "", "", "", "", "", "", "";
+};
+
+// EMMC group that excludes WP pin
+&pinctrl {
+ pinctrl_emmcg5_default: emmcg5_default {
+ function = "EMMC";
+ groups = "EMMCG5";
+ };
+};