@@ -108,6 +108,111 @@ bus@ff800000 {
#size-cells = <1>;
ranges = <0 0xff800000 0x800000>;
+ watchdog@480 {
+ compatible = "brcm,bcm6345-wdt";
+ reg = <0x480 0x10>;
+ };
+
+ watchdog@4c0 {
+ compatible = "brcm,bcm6345-wdt";
+ reg = <0x4c0 0x10>;
+ status = "disabled";
+ };
+
+ /* GPIOs 0 .. 31 */
+ gpio0: gpio@500 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x500 0x04>, <0x520 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 32 .. 63 */
+ gpio1: gpio@504 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x504 0x04>, <0x524 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 64 .. 95 */
+ gpio2: gpio@508 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x508 0x04>, <0x528 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 96 .. 127 */
+ gpio3: gpio@50c {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x50c 0x04>, <0x52c 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 128 .. 159 */
+ gpio4: gpio@510 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x510 0x04>, <0x530 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 160 .. 191 */
+ gpio5: gpio@514 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x514 0x04>, <0x534 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 192 .. 223 */
+ gpio6: gpio@518 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x518 0x04>, <0x538 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 224 .. 255 */
+ gpio7: gpio@51c {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x51c 0x04>, <0x53c 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ rng@b80 {
+ compatible = "brcm,iproc-rng200";
+ reg = <0xb80 0x28>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ leds: led-controller@700 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "brcm,bcm63138-leds";
+ reg = <0x700 0xdc>;
+ status = "disabled";
+ };
+
hsspi: spi@1000 {
#address-cells = <1>;
#size-cells = <0>;
@@ -134,6 +239,19 @@ nandcs: nand@0 {
};
};
+ pl081_dma: dma-controller@11000 {
+ compatible = "arm,pl081", "arm,primecell";
+ // The magic B105F00D info is missing
+ arm,primecell-periphid = <0x00041081>;
+ reg = <0x11000 0x1000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ memcpy-burst-size = <256>;
+ memcpy-bus-width = <32>;
+ clocks = <&periph_clk>;
+ clock-names = "apb_pclk";
+ #dma-cells = <2>;
+ };
+
uart0: serial@12000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x12000 0x1000>;
All the BCMBCA SoCs share a set of peripherals at 0xff800000, albeit at slightly varying memory locations on the bus and with varying IRQ assignments. Add the first and second watchdog, GPIO, RNG, LED and DMA blocks for the BCM6878 based on the vendor files 6878_map_part.h and 6878_intr.h from the "bcmopen-consumer" code drop. This SoC has up to 256 possible GPIOs due to having 8 registers with 32 GPIOs in each available. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- arch/arm/boot/dts/broadcom/bcm6878.dtsi | 118 ++++++++++++++++++++++++++++++++ 1 file changed, 118 insertions(+)