diff mbox

[RESEND,v2,1/7] ARM: dts: vf610: Add USB PHY and controller

Message ID 240a6eadc0050de82af3e174a999f67e0ca27afa.1408391385.git.stefan@agner.ch (mailing list archive)
State New, archived
Headers show

Commit Message

Stefan Agner Aug. 18, 2014, 8:07 p.m. UTC
This adds USB PHY and USB controller nodes. Vybrid SoCs have two
independent USB cores which each supports DR (dual role). However,
real OTG is not supported since the OTG ID pin is not available.

The PHYs are located within the anadig register range, hence we need
to change the length of the anadig registers.

Signed-off-by: Stefan Agner <stefan@agner.ch>
---
 arch/arm/boot/dts/vf610.dtsi | 46 +++++++++++++++++++++++++++++++++++++++++---
 1 file changed, 43 insertions(+), 3 deletions(-)
diff mbox

Patch

diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi
index 6a6190c..f36acb5 100644
--- a/arch/arm/boot/dts/vf610.dtsi
+++ b/arch/arm/boot/dts/vf610.dtsi
@@ -25,6 +25,8 @@ 
 		gpio2 = &gpio3;
 		gpio3 = &gpio4;
 		gpio4 = &gpio5;
+		usbphy0 = &usbphy0;
+		usbphy1 = &usbphy1;
 	};
 
 	cpus {
@@ -285,9 +287,25 @@ 
 				gpio-ranges = <&iomuxc 0 128 7>;
 			};
 
-			anatop@40050000 {
-				compatible = "fsl,vf610-anatop";
-				reg = <0x40050000 0x1000>;
+			anatop: anatop@40050000 {
+				compatible = "fsl,vf610-anatop", "syscon";
+				reg = <0x40050000 0x400>;
+			};
+
+			usbphy0: usbphy@40050800 {
+				compatible = "fsl,vf610-usbphy";
+				reg = <0x40050800 0x400>;
+				interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks VF610_CLK_USBPHY0>;
+				fsl,anatop = <&anatop>;
+			};
+
+			usbphy1: usbphy@40050c00 {
+				compatible = "fsl,vf610-usbphy";
+				reg = <0x40050c00 0x400>;
+				interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks VF610_CLK_USBPHY1>;
+				fsl,anatop = <&anatop>;
 			};
 
 			i2c0: i2c@40066000 {
@@ -309,6 +327,18 @@ 
 				reg = <0x4006b000 0x1000>;
 				#clock-cells = <1>;
 			};
+
+			usbdev0: usb@40034000 {
+				compatible = "fsl,vf610-usb", "fsl,imx27-usb";
+				reg = <0x40034000 0x800>;
+				interrupts = <0 75 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks VF610_CLK_USBC0>;
+				fsl,usbphy = <&usbphy0>;
+				dr_mode = "peripheral";
+				status = "disabled";
+			};
+
+
 		};
 
 		aips1: aips-bus@40080000 {
@@ -371,6 +401,16 @@ 
 				status = "disabled";
 			};
 
+			usbh1: usb@400b4000 {
+				compatible = "fsl,vf610-usb", "fsl,imx27-usb";
+				reg = <0x400b4000 0x800>;
+				interrupts = <0 76 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks VF610_CLK_USBC1>;
+				fsl,usbphy = <&usbphy1>;
+				dr_mode = "host";
+				status = "disabled";
+			};
+
 			ftm: ftm@400b8000 {
 				compatible = "fsl,ftm-timer";
 				reg = <0x400b8000 0x1000 0x400b9000 0x1000>;