| Message ID | 6bd3249a5f8ecd8af376145781c3f4345f198bdd.1565789825.git.baruch@tkos.co.il (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v3,1/2] arm64: dts: fsl: add support for Hummingboard Pulse | expand |
On Wed, Aug 14, 2019 at 04:37:04PM +0300, Baruch Siach wrote: > From: Jon Nettleton <jon@solid-run.com> > > The SolidRun Hummingboard Pulse carrier board carries the SolidRun > i.MX8MQ based SOM. > > Notably missing is PCIe support that depends on analog PLLOUT clock. > Current imx clk driver does not support this clock. > > Signed-off-by: Jon Nettleton <jon@solid-run.com> > Signed-off-by: Baruch Siach <baruch@tkos.co.il> > --- > v3: > Fix SD card power regulator enable gpio > Address Marco's comments: > - Reorder pinctrl properties > - Move imx8mq.dtsi include to the SOM .dtsi > - Add reg_ prefix to regulator labels > - Add pinctrl node to SD card regulator gpio > - Add label to SPI flash node > > v2: Address Fabio's comments: > - Remove redundant node nesting > - Fix comments style > - Use mainline DT bindings in UART and USB type C > - Fix node names > - Move &iomuxc to the end of file > --- > arch/arm64/boot/dts/freescale/Makefile | 1 + > .../freescale/imx8mq-hummingboard-pulse.dts | 256 +++++++++++++++ > .../boot/dts/freescale/imx8mq-sr-som.dtsi | 309 ++++++++++++++++++ > 3 files changed, 566 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi > > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile > index c043aca66572..6833b23e2dd2 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb > > dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb > diff --git a/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts b/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts > new file mode 100644 > index 000000000000..4beb3c456448 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts > @@ -0,0 +1,256 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > +/* > + * Copyright (C) 2018 Jon Nettleton <jon@solid-run.com> > + */ > + > +/dts-v1/; > + > +#include "dt-bindings/usb/pd.h" > +#include "imx8mq-sr-som.dtsi" > + > +/ { > + model = "SolidRun i.MX8MQ HummingBoard Pulse"; > + compatible = "solidrun,hummingboard-pulse", "fsl,imx8mq"; > + > + chosen { > + stdout-path = &uart1; > + }; > + > + reg_usdhc2_vmmc: regulator-usdhc2-vmmc { > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc2_vmmc>; > + regulator-name = "VSD_3V3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio1 13 GPIO_ACTIVE_LOW>; > + }; > + > + reg_v_5v0: regulator-v-5v0 { > + compatible = "regulator-fixed"; > + regulator-name = "v_5v0"; > + regulator-max-microvolt = <5000000>; > + regulator-min-microvolt = <5000000>; > + regulator-always-on; > + }; > +}; > + > +&i2c2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + clock-frequency = <100000>; > + status = "okay"; > + > + typec_ptn5100: usb-typec@50 { > + compatible = "nxp,ptn5110"; > + reg = <0x50>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_typec>; > + interrupt-parent = <&gpio1>; > + interrupts = <6 IRQ_TYPE_LEVEL_LOW>; > + > + connector { > + compatible = "usb-c-connector"; > + label = "USB-C"; > + data-role = "dual"; > + power-role = "dual"; > + try-power-role = "sink"; > + source-pdos = <PDO_FIXED(5000, 2000, ^ > + PDO_FIXED_USB_COMM | > + PDO_FIXED_SUSPEND | > + PDO_FIXED_EXTPOWER)>; It'd be nice to have the lines align with column marked with ^ above. > + sink-pdos = <PDO_FIXED(5000, 2000, ^ > + PDO_FIXED_USB_COMM | > + PDO_FIXED_SUSPEND | > + PDO_FIXED_EXTPOWER) > + PDO_FIXED(9000, 2000, It'd be nice to have it align with column marked with ^ above. > + PDO_FIXED_USB_COMM | > + PDO_FIXED_SUSPEND | > + PDO_FIXED_EXTPOWER)>; > + op-sink-microwatt = <9000000>; > + > + port { > + typec1_dr_sw: endpoint { > + remote-endpoint = <&usb1_drd_sw>; > + }; > + }; > + }; > + }; > +}; > + > +&i2c3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + clock-frequency = <100000>; > + status = "okay"; > + > + rtc@69 { > + compatible = "abracon,ab1805"; > + reg = <0x69>; > + abracon,tc-diode = "schottky"; > + abracon,tc-resistor = <3>; > + }; > +}; > + > +&uart2 { /* J35 header */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2>; > + assigned-clocks = <&clk IMX8MQ_CLK_UART2>; > + assigned-clock-parents = <&clk IMX8MQ_CLK_25M>; > + status = "okay"; > +}; > + > +&uart3 { /* Mikrobus */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + assigned-clocks = <&clk IMX8MQ_CLK_UART3>; > + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; > + uart-has-rtscts; > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; > + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; > + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; > + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; > + vmmc-supply = <®_usdhc2_vmmc>; > + status = "okay"; > +}; > + > +&usb_dwc3_0 { > + status = "okay"; > + dr_mode = "otg"; We usually put 'status' line at end of property list, so please flip them. > + > + port { > + usb1_drd_sw: endpoint { > + remote-endpoint = <&typec1_dr_sw>; > + }; > + }; > +}; > + > +&usb_dwc3_1 { > + status = "okay"; > + dr_mode = "host"; > +}; > + > +&usb3_phy0 { > + status = "okay"; > +}; > + > +&usb3_phy1 { > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog>; > + > + pinctrl_hog: hoggrp { > + fsl,pins = < > + /* MikroBus Analog */ > + MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x41 > + /* MikroBus Reset */ > + MX8MQ_IOMUXC_SAI2_RXD0_GPIO4_IO23 0x41 > + /* > + * The following 2 pins need to be commented out and > + * reconfigured to enable RTS/CTS on UART3 > + */ > + /* MikroBus PWM */ > + MX8MQ_IOMUXC_ECSPI1_MISO_GPIO5_IO8 0x41 > + /* MikroBus INT */ > + MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x41 > + >; > + }; > + > + pinctrl_i2c2: i2c2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f > + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f > + >; > + }; > + > + pinctrl_i2c3: i2c3grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f > + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f > + >; > + }; > + > + pinctrl_typec: typecgrp { > + fsl,pins = < > + MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x16 > + MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x17059 > + >; > + }; > + > + pinctrl_uart2: uart2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49 > + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49 > + >; > + }; > + > + pinctrl_uart3: uart3grp { > + fsl,pins = < > + MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49 > + MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49 > + /* > + * These pins are by default GPIO on the Mikro Bus > + * Header. To use RTS/CTS on UART3 comment them out > + * of the hoggrp and enable them here > + */ > + /* MX8MQ_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x49 */ > + /* MX8MQ_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x49 */ > + >; > + }; > + > + pinctrl_usdhc2_gpio: usdhc2grpgpio { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41 > + >; > + }; > + > + pinctrl_usdhc2_vmmc: usdhc2vmmcgpio { > + fsl,pins = < > + MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x41 > + >; > + }; > + > + pinctrl_usdhc2: usdhc2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83 > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3 > + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 > + >; > + }; > + > + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd > + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 > + >; > + }; > + > + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xdf > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xdf > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xdf > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xdf > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xdf > + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 > + >; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi > new file mode 100644 > index 000000000000..cd22d085d6c7 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi > @@ -0,0 +1,309 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > +/* > + * Copyright (C) 2018 Jon Nettleton <jon@solid-run.com> > + */ > + > +#include "imx8mq.dtsi" > + > +/ { > + reg_vdd_3v3: regulator-vdd-3v3 { > + compatible = "regulator-fixed"; > + regulator-always-on; > + regulator-name = "vdd_3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > +}; > + > +&pgc_gpu{ > + power-supply = <&sw1a_reg>; > +}; > + > +&fec1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_fec1>; > + phy-mode = "rgmii-id"; > + phy-handle = <ðphy0>; > + phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; > + phy-reset-duration = <2>; > + fsl,magic-packet; > + status = "okay"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy0: ethernet-phy@4 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <4>; > + }; > + }; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + clock-frequency = <400000>; > + status = "okay"; > + > + pmic: pmic@8 { > + compatible = "fsl,pfuze100"; > + reg = <0x08>; > + > + regulators { > + sw1a_reg: sw1ab { > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1875000>; > + }; > + > + sw1c_reg: sw1c { > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1875000>; > + }; > + > + sw2_reg: sw2 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + sw3a_reg: sw3ab { > + regulator-min-microvolt = <400000>; > + regulator-max-microvolt = <1975000>; > + regulator-always-on; > + }; > + > + sw4_reg: sw4 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + swbst_reg: swbst { > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5150000>; > + }; > + > + snvs_reg: vsnvs { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <3000000>; > + regulator-always-on; > + }; > + > + vref_reg: vrefddr { > + regulator-always-on; > + }; > + > + vgen1_reg: vgen1 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1550000>; > + }; > + > + vgen2_reg: vgen2 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1550000>; > + regulator-always-on; > + }; > + > + vgen3_reg: vgen3 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen4_reg: vgen4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen5_reg: vgen5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen6_reg: vgen6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + }; > + }; > +}; > + > +&qspi0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_qspi>; > + status = "okay"; > + > + /* SPI flash; not assembled by default */ > + spi_flash: flash@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + reg = <0>; > + compatible = "micron,n25q256a", "jedec,spi-nor"; > + spi-max-frequency = <29000000>; > + status = "disabled"; > + }; > +}; > + > +&uart1 { /* console */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + assigned-clocks = <&clk IMX8MQ_CLK_UART1>; > + assigned-clock-parents = <&clk IMX8MQ_CLK_25M>; > + assigned-clock-rates = <25000000>; > + status = "okay"; > +}; > + > +&uart4 { /* ublox BT */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart4>; > + assigned-clocks = <&clk IMX8MQ_CLK_UART4>; > + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; > + assigned-clock-rates = <80000000>; > + status = "okay"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; > + bus-width = <8>; > + non-removable; > + status = "okay"; > +}; > + > +&pgc_vpu { This one is out of alphabetical order. Shawn > + power-supply = <&sw1c_reg>; > +}; > + > +&wdog1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_wdog>; > + fsl,ext-reset-output; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl_fec1: fec1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3 > + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23 > + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f > + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f > + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f > + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f > + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 > + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 > + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 > + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 > + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f > + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 > + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 > + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f > + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 > + >; > + }; > + > + pinctrl_i2c1: i2c1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f > + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f > + >; > + }; > + > + pinctrl_pcie0: pcie0grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x74 > + MX8MQ_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x16 > + MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x16 > + >; > + }; > + > + pinctrl_qspi: qspigrp { > + fsl,pins = < > + MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82 > + MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 > + MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 > + MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 > + MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 > + MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 > + > + >; > + }; > + > + pinctrl_uart1: uart1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49 > + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49 > + MX8MQ_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 > + >; > + }; > + > + pinctrl_uart4: uart4grp { > + fsl,pins = < > + MX8MQ_IOMUXC_UART4_TXD_UART4_DCE_TX 0x49 > + MX8MQ_IOMUXC_UART4_RXD_UART4_DCE_RX 0x49 > + MX8MQ_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 > + >; > + }; > + > + pinctrl_usdhc1: usdhc1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 > + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 > + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 > + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 > + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 > + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83 > + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 > + >; > + }; > + > + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { > + fsl,pins = < > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd > + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd > + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd > + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd > + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd > + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d > + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 > + >; > + }; > + > + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { > + fsl,pins = < > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf > + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf > + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf > + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf > + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf > + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f > + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 > + >; > + }; > + > + pinctrl_wdog: wdoggrp { > + fsl,pins = < > + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 > + >; > + }; > +}; > -- > 2.20.1 >
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index c043aca66572..6833b23e2dd2 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts b/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts new file mode 100644 index 000000000000..4beb3c456448 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts @@ -0,0 +1,256 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2018 Jon Nettleton <jon@solid-run.com> + */ + +/dts-v1/; + +#include "dt-bindings/usb/pd.h" +#include "imx8mq-sr-som.dtsi" + +/ { + model = "SolidRun i.MX8MQ HummingBoard Pulse"; + compatible = "solidrun,hummingboard-pulse", "fsl,imx8mq"; + + chosen { + stdout-path = &uart1; + }; + + reg_usdhc2_vmmc: regulator-usdhc2-vmmc { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2_vmmc>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; + + reg_v_5v0: regulator-v-5v0 { + compatible = "regulator-fixed"; + regulator-name = "v_5v0"; + regulator-max-microvolt = <5000000>; + regulator-min-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <100000>; + status = "okay"; + + typec_ptn5100: usb-typec@50 { + compatible = "nxp,ptn5110"; + reg = <0x50>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_typec>; + interrupt-parent = <&gpio1>; + interrupts = <6 IRQ_TYPE_LEVEL_LOW>; + + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 2000, + PDO_FIXED_USB_COMM | + PDO_FIXED_SUSPEND | + PDO_FIXED_EXTPOWER)>; + sink-pdos = <PDO_FIXED(5000, 2000, + PDO_FIXED_USB_COMM | + PDO_FIXED_SUSPEND | + PDO_FIXED_EXTPOWER) + PDO_FIXED(9000, 2000, + PDO_FIXED_USB_COMM | + PDO_FIXED_SUSPEND | + PDO_FIXED_EXTPOWER)>; + op-sink-microwatt = <9000000>; + + port { + typec1_dr_sw: endpoint { + remote-endpoint = <&usb1_drd_sw>; + }; + }; + }; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clock-frequency = <100000>; + status = "okay"; + + rtc@69 { + compatible = "abracon,ab1805"; + reg = <0x69>; + abracon,tc-diode = "schottky"; + abracon,tc-resistor = <3>; + }; +}; + +&uart2 { /* J35 header */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + assigned-clocks = <&clk IMX8MQ_CLK_UART2>; + assigned-clock-parents = <&clk IMX8MQ_CLK_25M>; + status = "okay"; +}; + +&uart3 { /* Mikrobus */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + assigned-clocks = <&clk IMX8MQ_CLK_UART3>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; + uart-has-rtscts; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; + +&usb_dwc3_0 { + status = "okay"; + dr_mode = "otg"; + + port { + usb1_drd_sw: endpoint { + remote-endpoint = <&typec1_dr_sw>; + }; + }; +}; + +&usb_dwc3_1 { + status = "okay"; + dr_mode = "host"; +}; + +&usb3_phy0 { + status = "okay"; +}; + +&usb3_phy1 { + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* MikroBus Analog */ + MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x41 + /* MikroBus Reset */ + MX8MQ_IOMUXC_SAI2_RXD0_GPIO4_IO23 0x41 + /* + * The following 2 pins need to be commented out and + * reconfigured to enable RTS/CTS on UART3 + */ + /* MikroBus PWM */ + MX8MQ_IOMUXC_ECSPI1_MISO_GPIO5_IO8 0x41 + /* MikroBus INT */ + MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x41 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f + >; + }; + + pinctrl_typec: typecgrp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x16 + MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x17059 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49 + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49 + MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49 + /* + * These pins are by default GPIO on the Mikro Bus + * Header. To use RTS/CTS on UART3 comment them out + * of the hoggrp and enable them here + */ + /* MX8MQ_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x49 */ + /* MX8MQ_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x49 */ + >; + }; + + pinctrl_usdhc2_gpio: usdhc2grpgpio { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41 + >; + }; + + pinctrl_usdhc2_vmmc: usdhc2vmmcgpio { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x41 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83 + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3 + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xdf + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xdf + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xdf + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xdf + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xdf + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi new file mode 100644 index 000000000000..cd22d085d6c7 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi @@ -0,0 +1,309 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2018 Jon Nettleton <jon@solid-run.com> + */ + +#include "imx8mq.dtsi" + +/ { + reg_vdd_3v3: regulator-vdd-3v3 { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-name = "vdd_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&pgc_gpu{ + power-supply = <&sw1a_reg>; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + phy-reset-duration = <2>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clock-frequency = <400000>; + status = "okay"; + + pmic: pmic@8 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + sw3a_reg: sw3ab { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + regulator-always-on; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; +}; + +&qspi0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi>; + status = "okay"; + + /* SPI flash; not assembled by default */ + spi_flash: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + compatible = "micron,n25q256a", "jedec,spi-nor"; + spi-max-frequency = <29000000>; + status = "disabled"; + }; +}; + +&uart1 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + assigned-clocks = <&clk IMX8MQ_CLK_UART1>; + assigned-clock-parents = <&clk IMX8MQ_CLK_25M>; + assigned-clock-rates = <25000000>; + status = "okay"; +}; + +&uart4 { /* ublox BT */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + assigned-clocks = <&clk IMX8MQ_CLK_UART4>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; + assigned-clock-rates = <80000000>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&pgc_vpu { + power-supply = <&sw1c_reg>; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23 + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f + >; + }; + + pinctrl_pcie0: pcie0grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x74 + MX8MQ_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x16 + MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x16 + >; + }; + + pinctrl_qspi: qspigrp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82 + MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 + MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 + MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 + MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 + MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 + + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49 + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49 + MX8MQ_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MQ_IOMUXC_UART4_TXD_UART4_DCE_TX 0x49 + MX8MQ_IOMUXC_UART4_RXD_UART4_DCE_RX 0x49 + MX8MQ_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83 + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +};