From patchwork Wed Jan 11 17:19:08 2017 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Gregory CLEMENT X-Patchwork-Id: 9510779 Return-Path: Received: from mail.wl.linuxfoundation.org (pdx-wl-mail.web.codeaurora.org [172.30.200.125]) by pdx-korg-patchwork.web.codeaurora.org (Postfix) with ESMTP id 636AB601E7 for ; Wed, 11 Jan 2017 17:28:00 +0000 (UTC) Received: from mail.wl.linuxfoundation.org (localhost [127.0.0.1]) by mail.wl.linuxfoundation.org (Postfix) with ESMTP id 6618B28615 for ; Wed, 11 Jan 2017 17:28:00 +0000 (UTC) Received: by mail.wl.linuxfoundation.org (Postfix, from userid 486) id 5A36928626; Wed, 11 Jan 2017 17:28:00 +0000 (UTC) X-Spam-Checker-Version: SpamAssassin 3.3.1 (2010-03-16) on pdx-wl-mail.web.codeaurora.org X-Spam-Level: X-Spam-Status: No, score=-4.2 required=2.0 tests=BAYES_00, RCVD_IN_DNSWL_MED autolearn=unavailable version=3.3.1 Received: from bombadil.infradead.org (bombadil.infradead.org [198.137.202.9]) (using TLSv1.2 with cipher AES256-GCM-SHA384 (256/256 bits)) (No client certificate requested) by mail.wl.linuxfoundation.org (Postfix) with ESMTPS id B148928615 for ; Wed, 11 Jan 2017 17:27:59 +0000 (UTC) Received: from localhost ([127.0.0.1] helo=bombadil.infradead.org) by bombadil.infradead.org with esmtp (Exim 4.87 #1 (Red Hat Linux)) id 1cRMgm-0008SO-81; Wed, 11 Jan 2017 17:27:56 +0000 Received: from mail.free-electrons.com ([62.4.15.54]) by bombadil.infradead.org with esmtp (Exim 4.87 #1 (Red Hat Linux)) id 1cRMZz-0000lR-8j for linux-arm-kernel@lists.infradead.org; Wed, 11 Jan 2017 17:21:03 +0000 Received: by mail.free-electrons.com (Postfix, from userid 110) id DCB4A20790; Wed, 11 Jan 2017 18:20:13 +0100 (CET) Received: from localhost (83.146.29.93.rev.sfr.net [93.29.146.83]) by mail.free-electrons.com (Postfix) with ESMTPSA id A1859203FA; Wed, 11 Jan 2017 18:20:13 +0100 (CET) From: Gregory CLEMENT To: Ulf Hansson , Adrian Hunter , linux-mmc@vger.kernel.org Subject: [PATCH v5 05/12] dt: bindings: Add bindings for Marvell Xenon SD Host Controller Date: Wed, 11 Jan 2017 18:19:08 +0100 Message-Id: <89c95d0084da6ad7132caa54ca66eb619d8a5090.1484154449.git-series.gregory.clement@free-electrons.com> X-Mailer: git-send-email 2.11.0 In-Reply-To: References: In-Reply-To: References: X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3 X-CRM114-CacheID: sfid-20170111_092056_199811_085FC68F X-CRM114-Status: GOOD ( 19.66 ) X-BeenThere: linux-arm-kernel@lists.infradead.org X-Mailman-Version: 2.1.21 Precedence: list List-Id: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Cc: Jimmy Xu , Andrew Lunn , Mike Turquette , Nadav Haklai , Ziji Hu , Victor Gu , Doug Jones , linux-clk@vger.kernel.org, Jisheng Zhang , Yehuda Yitschak , Marcin Wojtas , Kostya Porotchkin , Hanna Hawa , Sebastian Hesselbarth , devicetree@vger.kernel.org, Jason Cooper , Rob Herring , Ryan Gao , Gregory CLEMENT , "Wei\(SOCP\) Liu" , linux-arm-kernel@lists.infradead.org, Thomas Petazzoni , Stephen Boyd , linux-kernel@vger.kernel.org, Wilson Ding MIME-Version: 1.0 Sender: "linux-arm-kernel" Errors-To: linux-arm-kernel-bounces+patchwork-linux-arm=patchwork.kernel.org@lists.infradead.org X-Virus-Scanned: ClamAV using ClamSMTP From: Hu Ziji Marvell Xenon SDHC can support eMMC/SD/SDIO. Add Xenon-specific properties. Also add properties for Xenon PHY setting. Signed-off-by: Hu Ziji Signed-off-by: Gregory CLEMENT Acked-by: Rob Herring --- Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt | 197 +++++++- 1 file changed, 197 insertions(+) create mode 100644 Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt diff --git a/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt new file mode 100644 index 000000000000..a3876d2cc616 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt @@ -0,0 +1,197 @@ +Marvell Xenon SDHCI Controller device tree bindings +This file documents differences between the core mmc properties +described by mmc.txt and the properties used by the Xenon implementation. + +Multiple SDHCs might be put into a single Xenon IP, to save size and cost. +Each SDHC is independent and owns independent resources, such as register sets, +clock and PHY. +Each SDHC should have an independent device tree node. + +Required Properties: +- compatible: should be one of the following + - "marvell,armada-3700-sdhci": For controllers on Armada-3700 SoC. + Must provide a second register area and marvell,pad-type. + - "marvell,armada-8k-sdhci": For controllers on Armada 7K/8K SoC + +- clocks: + Array of clocks required for SDHC. + Require at least input clock for Xenon IP core. + +- clock-names: + Array of names corresponding to clocks property. + The input clock for Xenon IP core should be named as "core". + +- reg: + * For "marvell,armada-3700-sdhci", two register areas. + The first one for Xenon IP register. The second one for the Armada 3700 SoC + PHY PAD Voltage Control register. + Please follow the examples with compatible "marvell,armada-3700-sdhci" + in below. + Please also check property marvell,pad-type in below. + + * For other compatible strings, one register area for Xenon IP. + +Optional Properties: +- mmccard: + mmccard child node must be provided when current SDHC is for eMMC. + Xenon SDHC often can support both SD and eMMC. This child node indicates that + current SDHC is for eMMC card. Thus Xenon eMMC specific configuration and + operations can be enabled prior to eMMC init sequence. + Please refer to Documentation/devicetree/bindings/mmc/mmc-card.txt. + This child node should not be set if current Xenon SDHC is for SD/SDIO. + +- bus-width: + When 8-bit data bus width is in use for eMMC, this property should be + explicitly provided and set as 8. + It is optional when data bus width is 4-bit or 1-bit. + +- mmc-ddr-1_8v: + Select this property when eMMC HS DDR is supported on SDHC side. + +- mmc-hs400-1_8v: + Select this property when eMMC HS400 is supported on SDHC side. + +- no-1-8-v: + Select this property when 1.8V signaling voltage supply is unavailable. + When this property is enabled, both mmc-ddr-1_8v and mmc-hs400-1_8v should be + cleared. + +- marvell,xenon-sdhc-id: + Indicate the corresponding bit index of current SDHC in + SDHC System Operation Control Register Bit[7:0]. + Set/clear the corresponding bit to enable/disable current SDHC. + If Xenon IP contains only one SDHC, this property is optional. + +- marvell,xenon-phy-type: + Xenon support mutilple types of PHYs. + To select eMMC 5.1 PHY, set: + marvell,xenon-phy-type = "emmc 5.1 phy" + eMMC 5.1 PHY is the default choice if this property is not provided. + To select eMMC 5.0 PHY, set: + marvell,xenon-phy-type = "emmc 5.0 phy" + + All those types of PHYs can support eMMC, SD and SDIO. + Please note that this property only presents the type of PHY. + It doesn't stand for the entire SDHC type or property. + For example, "emmc 5.1 phy" doesn't mean that this Xenon SDHC only supports + eMMC 5.1. + +- marvell,xenon-phy-znr: + Set PHY ZNR value. + Only available for eMMC PHY 5.1 and eMMC PHY 5.0. + Valid range = [0:0x1F]. + ZNR is set as 0xF by default if this property is not provided. + +- marvell,xenon-phy-zpr: + Set PHY ZPR value. + Only available for eMMC PHY 5.1 and eMMC PHY 5.0. + Valid range = [0:0x1F]. + ZPR is set as 0xF by default if this property is not provided. + +- marvell,xenon-phy-nr-success-tun: + Set the number of required consecutive successful sampling points used to + identify a valid sampling window, in tuning process. + Valid range = [1:7]. + Set as 0x4 by default if this property is not provided. + +- marvell,xenon-phy-tun-step-divider: + Set the divider for calculating TUN_STEP. + Set as 64 by default if this property is not provided. + +- marvell,xenon-phy-slow-mode: + If this property is selected, transfers will bypass PHY. + Only available when bus frequency lower than 55MHz in SDR mde. + Disabled by default. Please only try this property if timing issues always + occur with PHY enabled in eMMC HS SDR, SD SDR12, SD SDR25, SD SDR50 mode. + +- marvell,xenon-tun-count: + Xenon SDHC SoC usually doesn't provide re-tuning counter in + Capabilities Register 3 Bit[11:8]. + This property provides the re-tuning counter. + If this property is not set, default re-tuning counter will + be set as 0x9 in driver. + +- marvell,pad-type: + Type of Armada 3700 SoC PHY PAD Voltage Controller register. + Only valid when "marvell,armada-3700-sdhci" is selected. + Two types: "sd" and "fixed-1-8v". + If "sd" is slected, SoC PHY PAD is set as 3.3V at the beginning and is + switched to 1.8V when SD in UHS-I. + If "fixed-1-8v" is slected, SoC PHY PAD is fixed 1.8V, such as for eMMC. + Please follow the examples with compatible "marvell,armada-3700-sdhci" + in below. + +Example: +- For eMMC: + + sdhci@aa0000 { + compatible = "marvell,armada-8k-sdhci"; + reg = <0xaa0000 0x1000>; + interrupts = + clocks = <&emmc_clk>; + clock-names = "core"; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs400-1_8v; + marvell,xenon-sdhc-id = <0>; + marvell,xenon-phy-type = "emmc 5.1 phy"; + marvell,xenon-tun-count = <11>; + + #address-cells = <1>; + #size-cells = <0>; + mmccard: mmccard@0 { + compatible = "mmc-card"; + reg = <0>; + }; + }; + +- For SD/SDIO: + + sdhci@ab0000 { + compatible = "marvell,armada-8k-sdhci"; + reg = <0xab0000 0x1000>; + interrupts = + vqmmc-supply = <&sd_regulator>; + clocks = <&sdclk>; + clock-names = "core"; + bus-width = <4>; + marvell,xenon-tun-count = <9>; + }; + +- For eMMC with compatible "marvell,armada-3700-sdhci": + + sdhci@aa0000 { + compatible = "marvell,armada-3700-sdhci"; + reg = <0xaa0000 0x1000>, + ; + interrupts = + clocks = <&emmcclk>; + clock-names = "core"; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs400-1_8v; + + marvell,pad-type = "fixed-1-8v"; + + #address-cells = <1>; + #size-cells = <0>; + mmccard: mmccard@0 { + compatible = "mmc-card"; + reg = <0>; + }; + }; + +- For SD/SDIO with compatible "marvell,armada-3700-sdhci": + + sdhci@ab0000 { + compatible = "marvell,armada-3700-sdhci"; + reg = <0xab0000 0x1000>, + ; + interrupts = + vqmmc-supply = <&sd_regulator>; + clocks = <&sdclk>; + clock-names = "core"; + bus-width = <4>; + + marvell,pad-type = "sd"; + };