| Message ID | BANLkTimRB8z16wjyH1fuXbiybQuaJL4Qug@mail.gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Tue, 31 May 2011, Daniel Drake wrote: > On 31 May 2011 21:33, Per Forlin <per.forlin@linaro.org> wrote: > > Daniel Drake reported an issue in the libertas sdio client that was > > triggered by the sdio_single_irq functionality. His SDIO device seems to > > raise an interrupt even though there are no bits set in the CCCR_INTx > > register. This behaviour is not supported by the sdio_single_irq feature nor > > the SDIO spec. The purpose of the sdio_single_irq feature is to avoid the > > overhead of checking the CCCR_INTx registers, this result in no error > > handling of the case if there is a pending IRQ with none CCCR_INTx bits set. > > Thanks a lot for diagnosing this and nice work on figuring out the > root cause presumably without even having access to the hardware! > > I've looked further, based on your findings, and have found that you > are correct. During initialisation, exactly one interrupt is received > with CCCR_INTx=0. Previously the mmc stack threw this interrupt away, > after the optimization it now calls into libertas before it is ready > to handle interrupts, leading to the crash. From that point, all other > interrupts that come in are "normal". > > This is definitely a weird hardware issue, and it would annoy me for > this hardware to cause a second generic mmc layer feature be disabled > by default! And actually it is not much work to harden up the libertas > driver to be able to accept that spurious IRQ, and during the process > of fixing that it actually made the spurious IRQ go away completely. > > Patch attached. > > So, I vote for that we work around this little hardware issue in the > libertas driver, and leave this optimization enabled by default until > we find a hardware issue that is more difficult to workaround. I can > take on submission of the libertas patch. > > Thoughts? This is definitively the best approach. Thanks for fixing the root cause. Nicolas
diff --git a/drivers/net/wireless/libertas/if_sdio.c b/drivers/net/wireless/libertas/if_sdio.c index a7b5cb0..224e985 100644 --- a/drivers/net/wireless/libertas/if_sdio.c +++ b/drivers/net/wireless/libertas/if_sdio.c @@ -907,7 +907,7 @@ static void if_sdio_interrupt(struct sdio_func *func) card = sdio_get_drvdata(func); cause = sdio_readb(card->func, IF_SDIO_H_INT_STATUS, &ret); - if (ret) + if (ret || !cause) goto out; lbs_deb_sdio("interrupt: 0x%X\n", (unsigned)cause); @@ -1008,10 +1008,6 @@ static int if_sdio_probe(struct sdio_func *func, if (ret) goto release; - ret = sdio_claim_irq(func, if_sdio_interrupt); - if (ret) - goto disable; - /* For 1-bit transfers to the 8686 model, we need to enable the * interrupt flag in the CCCR register. Set the MMC_QUIRK_LENIENT_FN0 * bit to allow access to non-vendor registers. */ @@ -1083,6 +1079,21 @@ static int if_sdio_probe(struct sdio_func *func, card->rx_unit = 0; /* + * Set up the interrupt handler late. + * + * If we set it up earlier, the (buggy) hardware generates a spurious + * interrupt, even before the interrupt has been enabled, with + * CCCR_INTx = 0. + * + * We register the interrupt handler late so that we can handle any + * spurious interrupts, and also to avoid generation of that known + * spurious interrupt in the first place. + */ + ret = sdio_claim_irq(func, if_sdio_interrupt); + if (ret) + goto disable; + + /* * Enable interrupts now that everything is set up */ sdio_writeb(func, 0x0f, IF_SDIO_H_INT_MASK, &ret);