| Message ID | CAOMqctRS6sEcQ9sy7dqX_TH4gsRiywCN1nUJiQtXAa7NtoboOw@mail.gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 22 May 2016 at 18:41, Michal Suchanek <hramrach@gmail.com> wrote: > Hello, > > The debugfs output shows that spi2 is reparented under pll5 and the > pll5 frequency remains unchanged. > > The request to get a 2GHz clock for spi is fulfilled on best-effort > basis by giving the 864MHz pll5 clock which should theoretically > result in 432MHz SPI clock. > > On 22 May 2016 at 16:58, Chen-Yu Tsai <wens@csie.org> wrote: >> Hi, >> >> On Sun, May 22, 2016 at 10:18 PM, Michal Suchanek <hramrach@gmail.com> wrote: >>> Hello, >>> >>> I tried running a spidev test program on linux 4.6 and I uncovered a >>> problem with the sunxi clk framework. >>> >>> Basically the system would lock up after running the test program. >>> >>> Digging deeper I found that it locks up with commit >>> [47284e3e0f3c427c93f8583549b6c938e8a18015] spi: sun4i: allow transfers >>> to set transmission speed >>> >>> This exposes a problem with the test program. I try to set the SPI >>> sped to 1MHz but at other place the speed is multiplied by 1000 to >>> save typing zeros so the actual requested speed is 1GHz. This commit >>> probably allows that request to propagate leading to the observed >>> system lockup. >>> >>> Given the parents OSC24M, pll6 and pll5 one of pll6 and pll5 is >>> probably set up at 2GHz (or both in turn because due to some rounding >>> neither goes fully up to 2GHz resulting in 864000000 SPI clock). Then >>> the system locks up. >> >> IIRC the mod clock does not propagate rate changes up the tree. >> But some output from the debugfs would be helpful. See below. >> >>> >>> I can limit the speed in the SPI driver which is rated at 100MHz in >>> SoC manual (giving 200MHz pll) but the clk driver should probably >>> limit the clock setting to sane speeds itself. >>> >>> I am not familiar with the sunxi-clk code and it has unfortunately no >>> debug prints which would show what is programmed to what speed. >> >> You can use /sys/kernel/debug/clk/clk_summary, provided you have >> debugfs built in and mounted. > > root@a10s:~/spidisp# ./spitest -d -s 1000000 /dev/spidev2.0 > Debug mode. > /dev/spidev2.0: spi mode 0x0, 8 bits per word, 1000000000 Hz max > Sending 00 > clock enable_cnt prepare_cnt rate > accuracy phase > ---------------------------------------------------------------------------------------- > osc32k 0 0 32768 > 0 0 > osc24M 6 6 24000000 > 0 0 > ir0 0 0 24000000 > 0 0 > spi2 0 0 24000000 > 0 0 > spi1 0 0 24000000 > 0 0 > spi0 0 0 24000000 > 0 0 > ... > spi_master spi2: spi2.0: timeout transferring 1 bytes@1000000000Hz for > 100(100)ms > spidev spi2.0: SPI transfer failed: -110 > spi_master spi2: failed to transfer one message from queue > ... > pll5 1 1 864000000 > 0 0 > pll5_other 0 0 864000000 > 0 0 > pll5_ddr 1 1 432000000 > 0 0 > ... > xfer: Connection timed out > buffer size: 1, result -110 > buffer size: 1, result -110, Connection timed out > Sending > clock enable_cnt prepare_cnt rate > accuracy phase > ---------------------------------------------------------------------------------------- > osc32k 0 0 32768 > 0 0 > osc24M 6 6 24000000 > 0 0 > ir0 0 0 24000000 > 0 0 > spi1 0 0 24000000 > 0 0 > spi0 0 0 24000000 > 0 0 > ss 0 0 24000000 > 0 0 > ... > pll5 1 1 864000000 > 0 0 > pll5_other 0 0 864000000 > 0 0 > spi2 0 0 864000000 > 0 0 > pll5_ddr 1 1 432000000 > 0 0 > ... > maximum buffer size: 0 > Sending 9f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > ... > pll5 1 1 864000000 > 0 0 > pll5_other 0 0 864000000 > 0 0 > spi2 0 0 864000000 > 0 0 > pll5_ddr 1 1 432000000 > 0 0 > pll4 0 0 384000000 > 0 0 > pll2-prediv 0 > > The system locks up here before finishing the output from debugfs and > actually starting the transfer printed above. > Actually the serial console speed is limited so the system might be doing something else already while transferring this debug output. Thanks Michal
--- clk1.txt 2016-05-22 18:38:24.890906037 +0200 +++ clk2.txt 2016-05-22 18:38:15.891003130 +0200 @@ -3,7 +3,6 @@ osc32k 0 0 32768 0 0 osc24M 6 6 24000000 0 0 ir0 0 0 24000000 0 0 - spi2 0 0 24000000