@@ -617,25 +617,15 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
/* Set up the bus widths to the maximum */
bd.srcbus.buswidth = bd.srcbus.maxwidth;
bd.dstbus.buswidth = bd.dstbus.maxwidth;
- dev_vdbg(&pl08x->adev->dev,
- "%s source bus is %d bytes wide, dest bus is %d bytes wide\n",
- __func__, bd.srcbus.buswidth, bd.dstbus.buswidth);
-
/*
* Bytes transferred == tsize * MIN(buswidths), not max(buswidths)
*/
max_bytes_per_lli = min(bd.srcbus.buswidth, bd.dstbus.buswidth) *
PL080_CONTROL_TRANSFER_SIZE_MASK;
- dev_vdbg(&pl08x->adev->dev,
- "%s max bytes per lli = %zu\n",
- __func__, max_bytes_per_lli);
/* We need to count this down to zero */
bd.remainder = txd->len;
- dev_vdbg(&pl08x->adev->dev,
- "%s remainder = %zu\n",
- __func__, bd.remainder);
/*
* Choose bus to align to
@@ -644,6 +634,16 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
*/
pl08x_choose_master_bus(&bd, &mbus, &sbus, cctl);
+ dev_vdbg(&pl08x->adev->dev, "src=0x%08x%s/%u dst=0x%08x%s/%u len=%zu llimax=%zu\n",
+ bd.srcbus.addr, cctl & PL080_CONTROL_SRC_INCR ? "+" : "",
+ bd.srcbus.buswidth,
+ bd.dstbus.addr, cctl & PL080_CONTROL_DST_INCR ? "+" : "",
+ bd.dstbus.buswidth,
+ bd.remainder, max_bytes_per_lli);
+ dev_vdbg(&pl08x->adev->dev, "mbus=%s sbus=%s\n",
+ mbus == &bd.srcbus ? "src" : "dst",
+ sbus == &bd.srcbus ? "src" : "dst");
+
if (txd->len < mbus->buswidth) {
/* Less than a bus width available - send as single bytes */
while (bd.remainder) {
@@ -835,15 +835,14 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
{
int i;
+ dev_vdbg(&pl08x->adev->dev,
+ "%-3s %-9s %-10s %-10s %-10s %s\n",
+ "lli", "", "csrc", "cdst", "clli", "cctl");
for (i = 0; i < num_llis; i++) {
dev_vdbg(&pl08x->adev->dev,
- "lli %d @%p: csrc=0x%08x, cdst=0x%08x, cctl=0x%08x, clli=0x%08x\n",
- i,
- &llis_va[i],
- llis_va[i].src,
- llis_va[i].dst,
- llis_va[i].cctl,
- llis_va[i].lli
+ "%3d @%p: 0x%08x 0x%08x 0x%08x 0x%08x\n",
+ i, &llis_va[i], llis_va[i].src,
+ llis_va[i].dst, llis_va[i].lli, llis_va[i].cctl
);
}
}
Clean up debugging when setting up the LLI list. This reduces the amount of output while preserving the information, and makes it easier to read. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> --- drivers/dma/amba-pl08x.c | 33 ++++++++++++++++----------------- 1 files changed, 16 insertions(+), 17 deletions(-)