@@ -12,6 +12,7 @@
*/
#include <linux/init.h>
+#include <linux/gpio/machine.h>
#include <linux/kernel.h>
#include <linux/platform_data/sa11x0-serial.h>
#include <linux/mtd/mtd.h>
@@ -99,8 +100,30 @@ static void __init nanoengine_map_io(void)
Ser2HSCR0 = 0;
}
+static struct gpiod_lookup_table nanoengine_pcmcia0_gpio_table = {
+ .dev_id = "sa11x0-pcmcia.0",
+ .table = {
+ GPIO_LOOKUP("gpio", 11, "ready", GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP("gpio", 13, "detect", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio", 15, "reset", GPIO_ACTIVE_HIGH),
+ { },
+ },
+};
+
+static struct gpiod_lookup_table nanoengine_pcmcia1_gpio_table = {
+ .dev_id = "sa11x0-pcmcia.1",
+ .table = {
+ GPIO_LOOKUP("gpio", 12, "ready", GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP("gpio", 14, "detect", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio", 16, "reset", GPIO_ACTIVE_HIGH),
+ { },
+ },
+};
+
static void __init nanoengine_init(void)
{
+ sa11x0_register_pcmcia(0, &nanoengine_pcmcia0_gpio_table);
+ sa11x0_register_pcmcia(1, &nanoengine_pcmcia1_gpio_table);
sa11x0_register_mtd(&nanoengine_flash_data, nanoengine_flash_resources,
ARRAY_SIZE(nanoengine_flash_resources));
}
@@ -118,9 +118,6 @@ static int (*sa11x0_pcmcia_legacy_hw_init[])(struct device *dev) = {
#if defined(CONFIG_SA1100_H3100) || defined(CONFIG_SA1100_H3600)
pcmcia_h3600_init,
#endif
-#ifdef CONFIG_SA1100_NANOENGINE
- pcmcia_nanoengine_init,
-#endif
#ifdef CONFIG_SA1100_SHANNON
pcmcia_shannon_init,
#endif
@@ -11,7 +11,6 @@ extern int pcmcia_freebird_init(struct device *);
extern int pcmcia_gcplus_init(struct device *);
extern int pcmcia_graphicsmaster_init(struct device *);
extern int pcmcia_h3600_init(struct device *);
-extern int pcmcia_nanoengine_init(struct device *);
extern int pcmcia_pangolin_init(struct device *);
extern int pcmcia_pfs168_init(struct device *);
extern int pcmcia_shannon_init(struct device *);
deleted file mode 100644
@@ -1,133 +0,0 @@
-/*
- * drivers/pcmcia/sa1100_nanoengine.c
- *
- * PCMCIA implementation routines for BSI nanoEngine.
- *
- * In order to have a fully functional pcmcia subsystem in a BSE nanoEngine
- * board you should carefully read this:
- * http://cambuca.ldhs.cetuc.puc-rio.br/nanoengine/
- *
- * Copyright (C) 2010 Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
- *
- * Based on original work for kernel 2.4 by
- * Miguel Freitas <miguel@cpti.cetuc.puc-rio.br>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-#include <linux/device.h>
-#include <linux/errno.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/signal.h>
-
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/nanoengine.h>
-
-#include "sa1100_generic.h"
-
-struct nanoengine_pins {
- unsigned output_pins;
- unsigned clear_outputs;
- int gpio_rst;
- int gpio_cd;
- int gpio_rdy;
-};
-
-static struct nanoengine_pins nano_skts[] = {
- {
- .gpio_rst = GPIO_PC_RESET0,
- .gpio_cd = GPIO_PC_CD0,
- .gpio_rdy = GPIO_PC_READY0,
- }, {
- .gpio_rst = GPIO_PC_RESET1,
- .gpio_cd = GPIO_PC_CD1,
- .gpio_rdy = GPIO_PC_READY1,
- }
-};
-
-unsigned num_nano_pcmcia_sockets = ARRAY_SIZE(nano_skts);
-
-static int nanoengine_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
-{
- unsigned i = skt->nr;
- int ret;
-
- if (i >= num_nano_pcmcia_sockets)
- return -ENXIO;
-
- ret = gpio_request_one(nano_skts[i].gpio_rst, GPIOF_OUT_INIT_LOW,
- i ? "PC RST1" : "PC RST0");
- if (ret)
- return ret;
-
- skt->stat[SOC_STAT_CD].gpio = nano_skts[i].gpio_cd;
- skt->stat[SOC_STAT_CD].name = i ? "PC CD1" : "PC CD0";
- skt->stat[SOC_STAT_RDY].gpio = nano_skts[i].gpio_rdy;
- skt->stat[SOC_STAT_RDY].name = i ? "PC RDY1" : "PC RDY0";
-
- return 0;
-}
-
-static void nanoengine_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
-{
- gpio_free(nano_skts[skt->nr].gpio_rst);
-}
-
-static int nanoengine_pcmcia_configure_socket(
- struct soc_pcmcia_socket *skt, const socket_state_t *state)
-{
- unsigned i = skt->nr;
-
- if (i >= num_nano_pcmcia_sockets)
- return -ENXIO;
-
- gpio_set_value(nano_skts[skt->nr].gpio_rst, !!(state->flags & SS_RESET));
-
- return 0;
-}
-
-static void nanoengine_pcmcia_socket_state(
- struct soc_pcmcia_socket *skt, struct pcmcia_state *state)
-{
- unsigned i = skt->nr;
-
- if (i >= num_nano_pcmcia_sockets)
- return;
-
- state->bvd1 = 1;
- state->bvd2 = 1;
- state->vs_3v = 1; /* Can only apply 3.3V */
- state->vs_Xv = 0;
-}
-
-static struct pcmcia_low_level nanoengine_pcmcia_ops = {
- .owner = THIS_MODULE,
-
- .hw_init = nanoengine_pcmcia_hw_init,
- .hw_shutdown = nanoengine_pcmcia_hw_shutdown,
-
- .configure_socket = nanoengine_pcmcia_configure_socket,
- .socket_state = nanoengine_pcmcia_socket_state,
-};
-
-int pcmcia_nanoengine_init(struct device *dev)
-{
- int ret = -ENODEV;
-
- if (machine_is_nanoengine())
- ret = sa11xx_drv_pcmcia_probe(
- dev, &nanoengine_pcmcia_ops, 0, 2);
-
- return ret;
-}
-
Convert nanoengine to use the generic CF socket support. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> --- arch/arm/mach-sa1100/nanoengine.c | 23 +++++++ drivers/pcmcia/sa1100_generic.c | 3 - drivers/pcmcia/sa1100_generic.h | 1 - drivers/pcmcia/sa1100_nanoengine.c | 133 ------------------------------------- 4 files changed, 23 insertions(+), 137 deletions(-) delete mode 100644 drivers/pcmcia/sa1100_nanoengine.c