@@ -136,6 +136,20 @@ static struct pxa2xx_udc_mach_info udc_info __initdata = {
// no D+ pullup; lubbock can't connect/disconnect in software
};
+/* GPIOs for SA1111 PCMCIA */
+static struct gpiod_lookup_table sa1111_pcmcia_gpio_table = {
+ .dev_id = "1800",
+ .table = {
+ { "sa1111", 0, "a0vpp", GPIO_ACTIVE_HIGH },
+ { "sa1111", 1, "a1vpp", GPIO_ACTIVE_HIGH },
+ { "sa1111", 2, "a0vcc", GPIO_ACTIVE_HIGH },
+ { "sa1111", 3, "a1vcc", GPIO_ACTIVE_HIGH },
+ { "lubbock", 14, "b0vcc", GPIO_ACTIVE_HIGH },
+ { "lubbock", 15, "b1vcc", GPIO_ACTIVE_HIGH },
+ { },
+ },
+};
+
static struct resource sa1111_resources[] = {
[0] = {
.start = 0x10000000,
@@ -475,6 +489,8 @@ static void __init lubbock_init(void)
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
+ gpiod_add_lookup_table(&sa1111_pcmcia_gpio_table);
+
clk_add_alias("SA1111_CLK", NULL, "GPIO11_CLK", NULL);
pxa_set_udc_info(&udc_info);
pxa_set_fb_info(NULL, &sharp_lm8v31);
@@ -195,6 +195,7 @@ config PCMCIA_SA1111
select PCMCIA_SA11XX_BASE if ARCH_SA1100
select PCMCIA_PXA2XX if ARCH_LUBBOCK && SA1111
select PCMCIA_MAX1600 if ASSABET_NEPONSET
+ select PCMCIA_MAX1600 if ARCH_LUBBOCK && SA1111
help
Say Y here to include support for SA1111-based PCMCIA or CF
sockets, found on the Jornada 720, Graphicsmaster and other
@@ -24,20 +24,33 @@
#include <mach/hardware.h>
#include <asm/hardware/sa1111.h>
#include <asm/mach-types.h>
-#include <mach/lubbock.h>
#include "sa1111_generic.h"
+#include "max1600.h"
+
+static int lubbock_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+ struct sa1111_pcmcia_socket *s = to_skt(skt);
+ struct max1600 *m;
+ int ret;
+
+ ret = max1600_init(skt->socket.dev.parent, &m,
+ skt->nr ? MAX1600_CHAN_B : MAX1600_CHAN_A,
+ MAX1600_CODE_HIGH);
+ if (ret == 0)
+ s->driver_data = m;
+
+ return ret;
+}
static int
lubbock_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
const socket_state_t *state)
{
struct sa1111_pcmcia_socket *s = to_skt(skt);
- unsigned int pa_dwr_mask, pa_dwr_set, misc_mask, misc_set;
+ struct max1600 *m = s->driver_data;
int ret = 0;
- pa_dwr_mask = pa_dwr_set = misc_mask = misc_set = 0;
-
/* Lubbock uses the Maxim MAX1602, with the following connections:
*
* Socket 0 (PCMCIA):
@@ -71,74 +84,7 @@ lubbock_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
again:
switch (skt->nr) {
case 0:
- pa_dwr_mask = GPIO_A0 | GPIO_A1 | GPIO_A2 | GPIO_A3;
-
- switch (state->Vcc) {
- case 0: /* Hi-Z */
- break;
-
- case 33: /* VY */
- pa_dwr_set |= GPIO_A3;
- break;
-
- case 50: /* VX */
- pa_dwr_set |= GPIO_A2;
- break;
-
- default:
- printk(KERN_ERR "%s(): unrecognized Vcc %u\n",
- __func__, state->Vcc);
- ret = -1;
- }
-
- switch (state->Vpp) {
- case 0: /* Hi-Z */
- break;
-
- case 120: /* 12IN */
- pa_dwr_set |= GPIO_A1;
- break;
-
- default: /* VCC */
- if (state->Vpp == state->Vcc)
- pa_dwr_set |= GPIO_A0;
- else {
- printk(KERN_ERR "%s(): unrecognized Vpp %u\n",
- __func__, state->Vpp);
- ret = -1;
- break;
- }
- }
- break;
-
case 1:
- misc_mask = (1 << 15) | (1 << 14);
-
- switch (state->Vcc) {
- case 0: /* Hi-Z */
- break;
-
- case 33: /* VY */
- misc_set |= 1 << 15;
- break;
-
- case 50: /* VX */
- misc_set |= 1 << 14;
- break;
-
- default:
- printk(KERN_ERR "%s(): unrecognized Vcc %u\n",
- __func__, state->Vcc);
- ret = -1;
- break;
- }
-
- if (state->Vpp != state->Vcc && state->Vpp != 0) {
- printk(KERN_ERR "%s(): CF slot cannot support Vpp %u\n",
- __func__, state->Vpp);
- ret = -1;
- break;
- }
break;
default:
@@ -147,11 +93,8 @@ lubbock_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
if (ret == 0)
ret = sa1111_pcmcia_configure_socket(skt, state);
-
- if (ret == 0) {
- lubbock_set_misc_wr(misc_mask, misc_set);
- sa1111_set_io(s->dev, pa_dwr_mask, pa_dwr_set);
- }
+ if (ret == 0)
+ ret = max1600_configure(m, state->Vcc, state->Vpp);
#if 1
if (ret == 0 && state->Vcc == 33) {
@@ -175,8 +118,7 @@ lubbock_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
/*
* Switch to 5V, Configure socket with 5V voltage
*/
- lubbock_set_misc_wr(misc_mask, 0);
- sa1111_set_io(s->dev, pa_dwr_mask, 0);
+ max1600_configure(m, 0, 0);
/*
* It takes about 100ms to turn off Vcc.
@@ -201,6 +143,7 @@ lubbock_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
static struct pcmcia_low_level lubbock_pcmcia_ops = {
.owner = THIS_MODULE,
+ .hw_init = lubbock_pcmcia_hw_init,
.configure_socket = lubbock_pcmcia_configure_socket,
.first = 0,
.nr = 2,
@@ -213,17 +156,6 @@ int pcmcia_lubbock_init(struct sa1111_dev *sadev)
int ret = -ENODEV;
if (machine_is_lubbock()) {
- /*
- * Set GPIO_A<3:0> to be outputs for the MAX1600,
- * and switch to standby mode.
- */
- sa1111_set_io_dir(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0, 0);
- sa1111_set_io(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0);
- sa1111_set_sleep_io(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0);
-
- /* Set CF Socket 1 power to standby mode. */
- lubbock_set_misc_wr((1 << 15) | (1 << 14), 0);
-
pxa2xx_drv_pcmcia_ops(&lubbock_pcmcia_ops);
pxa2xx_configure_sockets(&sadev->dev);
ret = sa1111_pcmcia_add(sadev, &lubbock_pcmcia_ops,
As Lubbock now provides GPIOs via gpiolib for controlling the socket power, we can use the MAX1600 driver. Switch Lubbock to use this driver, which simplifies the code. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> --- arch/arm/mach-pxa/lubbock.c | 16 ++++++ drivers/pcmcia/Kconfig | 1 + drivers/pcmcia/sa1111_lubbock.c | 110 ++++++++-------------------------------- 3 files changed, 38 insertions(+), 89 deletions(-)