| Message ID | a19d0a70aacaf4c3517a226bf32ea49db3542da4.1674500205.git.geert+renesas@glider.be (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: dts: renesas: r8a779g0/white-hawk: Add CAN-FD support | expand |
Hello! On 1/23/23 10:06 PM, Geert Uytterhoeven wrote: > Enable confirmed-working CAN-FD channels 0 and 1 on the White-Hawk > development board: > - Channel 0 uses an NXP TJR1443AT CAN transceiver, which is be enabled Is be enabled? :-) > through a GPIO, > - Channels 1-7 use Microchip MCP2558FD-H/SN CAN transceivers (not > mounted for channels 4-7), which do not need explicit description, > but channels 2-3 do not seem to work. > > Inspired by a patch in the BSP by Kazuya Mizuguch. > > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> [...] MBR, Sergey
diff --git a/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk.dts b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk.dts index 04a2b6b83e743f32..eff1ef6e2cc83aba 100644 --- a/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk.dts +++ b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk.dts @@ -13,6 +13,33 @@ / { model = "Renesas White Hawk CPU and Breakout boards based on r8a779g0"; compatible = "renesas,white-hawk-breakout", "renesas,white-hawk-cpu", "renesas,r8a779g0"; + + can_transceiver0: can-phy0 { + compatible = "nxp,tjr1443"; + #phy-cells = <0>; + enable-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + max-bitrate = <5000000>; + }; +}; + +&can_clk { + clock-frequency = <40000000>; +}; + +&canfd { + pinctrl-0 = <&canfd0_pins>, <&canfd1_pins>, <&can_clk_pins>; + pinctrl-names = "default"; + + status = "okay"; + + channel0 { + status = "okay"; + phys = <&can_transceiver0>; + }; + + channel1 { + status = "okay"; + }; }; &i2c0 { @@ -23,3 +50,20 @@ eeprom@51 { pagesize = <8>; }; }; + +&pfc { + can_clk_pins: can-clk { + groups = "can_clk"; + function = "can_clk"; + }; + + canfd0_pins: canfd0 { + groups = "canfd0_data"; + function = "canfd0"; + }; + + canfd1_pins: canfd1 { + groups = "canfd1_data"; + function = "canfd1"; + }; +};
Enable confirmed-working CAN-FD channels 0 and 1 on the White-Hawk development board: - Channel 0 uses an NXP TJR1443AT CAN transceiver, which is be enabled through a GPIO, - Channels 1-7 use Microchip MCP2558FD-H/SN CAN transceivers (not mounted for channels 4-7), which do not need explicit description, but channels 2-3 do not seem to work. Inspired by a patch in the BSP by Kazuya Mizuguch. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- This depends on "[PATCH 2/2] phy: phy-can-transceiver: Add support for NXP TJR1443" https://lore.kernel.org/all/0bfa1e4c43632e49c9512b4e7daa970545545dcf.1674037830.git.geert+renesas@glider.be Changed compared to the BSP: - Add can_clk, - Add missing can_transceiver0, - Disable channels 2-7. Tested using cansend, candump, and canfdtest. - Channel 2 does not work: "bus-off" error message. - Channel 3 does not work: - Using cansend on another interface, and candump on can3 shows that nothing is received. However, my scope does see the data on the bus, and it is not sent repeatedly, hence it must have been acked by the receiver. - Using canfdtest on can3 gives: can3: Message ID mismatch! expected: 0078: [8] 01 02 03 04 05 06 07 08 received: 0077: [8] 00 01 02 03 04 05 06 07 Note that describing a plain gpio-hog instead of can_transceiver0 is not sufficient, as the enable signal must not be asserted before initialization of the CAN-FD controller, --- .../boot/dts/renesas/r8a779g0-white-hawk.dts | 44 +++++++++++++++++++ 1 file changed, 44 insertions(+)