| Message ID | e6230f49275e10e0cea625a8d806f3850ac2a29c.1573252696.git.leonard.crestez@nxp.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | PM / devfreq: Add dynamic scaling for imx8m ddr controller | expand |
On 19-11-09 00:39:52, Leonard Crestez wrote: > DRAM frequency switches are executed in firmware and can change the > configuration of the DRAM PLL outside linux. Mark these CLKs with > CLK_GET_RATE_NOCACHE so we always read back the PLL config registers and > recalculate rates. > > In current DRAM frequency tables on 8mm/8mn only the maximum frequency > uses the PLL so it's always configured in the same way. However reading > back the PLL configuration is the correct behavior and allows additional > setpoints in the future. > > Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> This one looks fine. Reviewed-by: Abel Vesa <abel.vesa@nxp.com> > --- > drivers/clk/imx/clk-imx8mm.c | 2 +- > drivers/clk/imx/clk-imx8mn.c | 2 +- > drivers/clk/imx/clk-pll14xx.c | 7 +++++++ > drivers/clk/imx/clk.h | 1 + > 4 files changed, 10 insertions(+), 2 deletions(-) > > diff --git a/drivers/clk/imx/clk-imx8mm.c b/drivers/clk/imx/clk-imx8mm.c > index c58f988191a5..d500bac3afa1 100644 > --- a/drivers/clk/imx/clk-imx8mm.c > +++ b/drivers/clk/imx/clk-imx8mm.c > @@ -326,11 +326,11 @@ static int imx8mm_clocks_probe(struct platform_device *pdev) > clks[IMX8MM_SYS_PLL3_REF_SEL] = imx_clk_mux("sys_pll3_ref_sel", base + 0x114, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels)); > > clks[IMX8MM_AUDIO_PLL1] = imx_clk_pll14xx("audio_pll1", "audio_pll1_ref_sel", base, &imx_1443x_pll); > clks[IMX8MM_AUDIO_PLL2] = imx_clk_pll14xx("audio_pll2", "audio_pll2_ref_sel", base + 0x14, &imx_1443x_pll); > clks[IMX8MM_VIDEO_PLL1] = imx_clk_pll14xx("video_pll1", "video_pll1_ref_sel", base + 0x28, &imx_1443x_pll); > - clks[IMX8MM_DRAM_PLL] = imx_clk_pll14xx("dram_pll", "dram_pll_ref_sel", base + 0x50, &imx_1443x_pll); > + clks[IMX8MM_DRAM_PLL] = imx_clk_pll14xx("dram_pll", "dram_pll_ref_sel", base + 0x50, &imx_1443x_dram_pll); > clks[IMX8MM_GPU_PLL] = imx_clk_pll14xx("gpu_pll", "gpu_pll_ref_sel", base + 0x64, &imx_1416x_pll); > clks[IMX8MM_VPU_PLL] = imx_clk_pll14xx("vpu_pll", "vpu_pll_ref_sel", base + 0x74, &imx_1416x_pll); > clks[IMX8MM_ARM_PLL] = imx_clk_pll14xx("arm_pll", "arm_pll_ref_sel", base + 0x84, &imx_1416x_pll); > clks[IMX8MM_SYS_PLL1] = imx_clk_fixed("sys_pll1", 800000000); > clks[IMX8MM_SYS_PLL2] = imx_clk_fixed("sys_pll2", 1000000000); > diff --git a/drivers/clk/imx/clk-imx8mn.c b/drivers/clk/imx/clk-imx8mn.c > index ca78cb1249a7..9c605ca1b631 100644 > --- a/drivers/clk/imx/clk-imx8mn.c > +++ b/drivers/clk/imx/clk-imx8mn.c > @@ -323,11 +323,11 @@ static int imx8mn_clocks_probe(struct platform_device *pdev) > clks[IMX8MN_SYS_PLL3_REF_SEL] = imx_clk_mux("sys_pll3_ref_sel", base + 0x114, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels)); > > clks[IMX8MN_AUDIO_PLL1] = imx_clk_pll14xx("audio_pll1", "audio_pll1_ref_sel", base, &imx_1443x_pll); > clks[IMX8MN_AUDIO_PLL2] = imx_clk_pll14xx("audio_pll2", "audio_pll2_ref_sel", base + 0x14, &imx_1443x_pll); > clks[IMX8MN_VIDEO_PLL1] = imx_clk_pll14xx("video_pll1", "video_pll1_ref_sel", base + 0x28, &imx_1443x_pll); > - clks[IMX8MN_DRAM_PLL] = imx_clk_pll14xx("dram_pll", "dram_pll_ref_sel", base + 0x50, &imx_1443x_pll); > + clks[IMX8MN_DRAM_PLL] = imx_clk_pll14xx("dram_pll", "dram_pll_ref_sel", base + 0x50, &imx_1443x_dram_pll); > clks[IMX8MN_GPU_PLL] = imx_clk_pll14xx("gpu_pll", "gpu_pll_ref_sel", base + 0x64, &imx_1416x_pll); > clks[IMX8MN_VPU_PLL] = imx_clk_pll14xx("vpu_pll", "vpu_pll_ref_sel", base + 0x74, &imx_1416x_pll); > clks[IMX8MN_ARM_PLL] = imx_clk_pll14xx("arm_pll", "arm_pll_ref_sel", base + 0x84, &imx_1416x_pll); > clks[IMX8MN_SYS_PLL1] = imx_clk_fixed("sys_pll1", 800000000); > clks[IMX8MN_SYS_PLL2] = imx_clk_fixed("sys_pll2", 1000000000); > diff --git a/drivers/clk/imx/clk-pll14xx.c b/drivers/clk/imx/clk-pll14xx.c > index 5c458199060a..a6d31a7262ef 100644 > --- a/drivers/clk/imx/clk-pll14xx.c > +++ b/drivers/clk/imx/clk-pll14xx.c > @@ -65,10 +65,17 @@ struct imx_pll14xx_clk imx_1443x_pll = { > .type = PLL_1443X, > .rate_table = imx_pll1443x_tbl, > .rate_count = ARRAY_SIZE(imx_pll1443x_tbl), > }; > > +struct imx_pll14xx_clk imx_1443x_dram_pll = { > + .type = PLL_1443X, > + .rate_table = imx_pll1443x_tbl, > + .rate_count = ARRAY_SIZE(imx_pll1443x_tbl), > + .flags = CLK_GET_RATE_NOCACHE, > +}; > + > struct imx_pll14xx_clk imx_1416x_pll = { > .type = PLL_1416X, > .rate_table = imx_pll1416x_tbl, > .rate_count = ARRAY_SIZE(imx_pll1416x_tbl), > }; > diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h > index bc5bb6ac8636..81122c9ab842 100644 > --- a/drivers/clk/imx/clk.h > +++ b/drivers/clk/imx/clk.h > @@ -50,10 +50,11 @@ struct imx_pll14xx_clk { > int flags; > }; > > extern struct imx_pll14xx_clk imx_1416x_pll; > extern struct imx_pll14xx_clk imx_1443x_pll; > +extern struct imx_pll14xx_clk imx_1443x_dram_pll; > > #define imx_clk_cpu(name, parent_name, div, mux, pll, step) \ > imx_clk_hw_cpu(name, parent_name, div, mux, pll, step)->clk > > #define clk_register_gate2(dev, name, parent_name, flags, reg, bit_idx, \ > -- > 2.17.1 >
diff --git a/drivers/clk/imx/clk-imx8mm.c b/drivers/clk/imx/clk-imx8mm.c index c58f988191a5..d500bac3afa1 100644 --- a/drivers/clk/imx/clk-imx8mm.c +++ b/drivers/clk/imx/clk-imx8mm.c @@ -326,11 +326,11 @@ static int imx8mm_clocks_probe(struct platform_device *pdev) clks[IMX8MM_SYS_PLL3_REF_SEL] = imx_clk_mux("sys_pll3_ref_sel", base + 0x114, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels)); clks[IMX8MM_AUDIO_PLL1] = imx_clk_pll14xx("audio_pll1", "audio_pll1_ref_sel", base, &imx_1443x_pll); clks[IMX8MM_AUDIO_PLL2] = imx_clk_pll14xx("audio_pll2", "audio_pll2_ref_sel", base + 0x14, &imx_1443x_pll); clks[IMX8MM_VIDEO_PLL1] = imx_clk_pll14xx("video_pll1", "video_pll1_ref_sel", base + 0x28, &imx_1443x_pll); - clks[IMX8MM_DRAM_PLL] = imx_clk_pll14xx("dram_pll", "dram_pll_ref_sel", base + 0x50, &imx_1443x_pll); + clks[IMX8MM_DRAM_PLL] = imx_clk_pll14xx("dram_pll", "dram_pll_ref_sel", base + 0x50, &imx_1443x_dram_pll); clks[IMX8MM_GPU_PLL] = imx_clk_pll14xx("gpu_pll", "gpu_pll_ref_sel", base + 0x64, &imx_1416x_pll); clks[IMX8MM_VPU_PLL] = imx_clk_pll14xx("vpu_pll", "vpu_pll_ref_sel", base + 0x74, &imx_1416x_pll); clks[IMX8MM_ARM_PLL] = imx_clk_pll14xx("arm_pll", "arm_pll_ref_sel", base + 0x84, &imx_1416x_pll); clks[IMX8MM_SYS_PLL1] = imx_clk_fixed("sys_pll1", 800000000); clks[IMX8MM_SYS_PLL2] = imx_clk_fixed("sys_pll2", 1000000000); diff --git a/drivers/clk/imx/clk-imx8mn.c b/drivers/clk/imx/clk-imx8mn.c index ca78cb1249a7..9c605ca1b631 100644 --- a/drivers/clk/imx/clk-imx8mn.c +++ b/drivers/clk/imx/clk-imx8mn.c @@ -323,11 +323,11 @@ static int imx8mn_clocks_probe(struct platform_device *pdev) clks[IMX8MN_SYS_PLL3_REF_SEL] = imx_clk_mux("sys_pll3_ref_sel", base + 0x114, 0, 2, pll_ref_sels, ARRAY_SIZE(pll_ref_sels)); clks[IMX8MN_AUDIO_PLL1] = imx_clk_pll14xx("audio_pll1", "audio_pll1_ref_sel", base, &imx_1443x_pll); clks[IMX8MN_AUDIO_PLL2] = imx_clk_pll14xx("audio_pll2", "audio_pll2_ref_sel", base + 0x14, &imx_1443x_pll); clks[IMX8MN_VIDEO_PLL1] = imx_clk_pll14xx("video_pll1", "video_pll1_ref_sel", base + 0x28, &imx_1443x_pll); - clks[IMX8MN_DRAM_PLL] = imx_clk_pll14xx("dram_pll", "dram_pll_ref_sel", base + 0x50, &imx_1443x_pll); + clks[IMX8MN_DRAM_PLL] = imx_clk_pll14xx("dram_pll", "dram_pll_ref_sel", base + 0x50, &imx_1443x_dram_pll); clks[IMX8MN_GPU_PLL] = imx_clk_pll14xx("gpu_pll", "gpu_pll_ref_sel", base + 0x64, &imx_1416x_pll); clks[IMX8MN_VPU_PLL] = imx_clk_pll14xx("vpu_pll", "vpu_pll_ref_sel", base + 0x74, &imx_1416x_pll); clks[IMX8MN_ARM_PLL] = imx_clk_pll14xx("arm_pll", "arm_pll_ref_sel", base + 0x84, &imx_1416x_pll); clks[IMX8MN_SYS_PLL1] = imx_clk_fixed("sys_pll1", 800000000); clks[IMX8MN_SYS_PLL2] = imx_clk_fixed("sys_pll2", 1000000000); diff --git a/drivers/clk/imx/clk-pll14xx.c b/drivers/clk/imx/clk-pll14xx.c index 5c458199060a..a6d31a7262ef 100644 --- a/drivers/clk/imx/clk-pll14xx.c +++ b/drivers/clk/imx/clk-pll14xx.c @@ -65,10 +65,17 @@ struct imx_pll14xx_clk imx_1443x_pll = { .type = PLL_1443X, .rate_table = imx_pll1443x_tbl, .rate_count = ARRAY_SIZE(imx_pll1443x_tbl), }; +struct imx_pll14xx_clk imx_1443x_dram_pll = { + .type = PLL_1443X, + .rate_table = imx_pll1443x_tbl, + .rate_count = ARRAY_SIZE(imx_pll1443x_tbl), + .flags = CLK_GET_RATE_NOCACHE, +}; + struct imx_pll14xx_clk imx_1416x_pll = { .type = PLL_1416X, .rate_table = imx_pll1416x_tbl, .rate_count = ARRAY_SIZE(imx_pll1416x_tbl), }; diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h index bc5bb6ac8636..81122c9ab842 100644 --- a/drivers/clk/imx/clk.h +++ b/drivers/clk/imx/clk.h @@ -50,10 +50,11 @@ struct imx_pll14xx_clk { int flags; }; extern struct imx_pll14xx_clk imx_1416x_pll; extern struct imx_pll14xx_clk imx_1443x_pll; +extern struct imx_pll14xx_clk imx_1443x_dram_pll; #define imx_clk_cpu(name, parent_name, div, mux, pll, step) \ imx_clk_hw_cpu(name, parent_name, div, mux, pll, step)->clk #define clk_register_gate2(dev, name, parent_name, flags, reg, bit_idx, \
DRAM frequency switches are executed in firmware and can change the configuration of the DRAM PLL outside linux. Mark these CLKs with CLK_GET_RATE_NOCACHE so we always read back the PLL config registers and recalculate rates. In current DRAM frequency tables on 8mm/8mn only the maximum frequency uses the PLL so it's always configured in the same way. However reading back the PLL configuration is the correct behavior and allows additional setpoints in the future. Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> --- drivers/clk/imx/clk-imx8mm.c | 2 +- drivers/clk/imx/clk-imx8mn.c | 2 +- drivers/clk/imx/clk-pll14xx.c | 7 +++++++ drivers/clk/imx/clk.h | 1 + 4 files changed, 10 insertions(+), 2 deletions(-)