| Message ID | fe0fb54d4c7b99fb148954c1c9a8b1902c2b7b9c.1606828668.git.stefan@agner.ch (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v2,1/5] arm64: dts: meson: g12b: odroid-n2: fix PHY deassert timing requirements | expand |
On Tue, Dec 1, 2020 at 2:21 PM Stefan Agner <stefan@agner.ch> wrote: > > According to the datasheet (Rev. 1.9) the RTL8211F requires at least > 72ms "for internal circuits settling time" before accessing the PHY > egisters. This fixes an issue seen on ODROID-C2 where the Ethernet > link doesn't come up when using ip link set down/up: > [ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down > [ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36) > [ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma > [ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed > [ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed > > Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings") > Signed-off-by: Stefan Agner <stefan@agner.ch> with the "registers" typo above fixed: Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts index 7be3e354093b..de27beafe9db 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts @@ -165,7 +165,7 @@ eth_phy0: ethernet-phy@0 { reg = <0>; reset-assert-us = <10000>; - reset-deassert-us = <30000>; + reset-deassert-us = <80000>; reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; interrupt-parent = <&gpio_intc>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts index 70fcfb7b0683..50de1d01e565 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts @@ -200,7 +200,7 @@ eth_phy0: ethernet-phy@0 { reg = <0>; reset-assert-us = <10000>; - reset-deassert-us = <30000>; + reset-deassert-us = <80000>; reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; interrupt-parent = <&gpio_intc>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi index 222ee8069cfa..9b0b81f191f1 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi @@ -126,7 +126,7 @@ eth_phy0: ethernet-phy@0 { reg = <0>; reset-assert-us = <10000>; - reset-deassert-us = <30000>; + reset-deassert-us = <80000>; reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; interrupt-parent = <&gpio_intc>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi index ad812854a107..a350fee1264d 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi @@ -147,7 +147,7 @@ eth_phy0: ethernet-phy@0 { reg = <0>; reset-assert-us = <10000>; - reset-deassert-us = <30000>; + reset-deassert-us = <80000>; reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; interrupt-parent = <&gpio_intc>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts index b08c4537f260..b2ab05c22090 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts @@ -82,7 +82,7 @@ external_phy: ethernet-phy@0 { /* External PHY reset is shared with internal PHY Led signal */ reset-assert-us = <10000>; - reset-deassert-us = <30000>; + reset-deassert-us = <80000>; reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; interrupt-parent = <&gpio_intc>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts index bff8ec2c1c70..e38d9e50caa7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts @@ -194,7 +194,7 @@ external_phy: ethernet-phy@0 { reg = <0>; reset-assert-us = <10000>; - reset-deassert-us = <30000>; + reset-deassert-us = <80000>; reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; interrupt-parent = <&gpio_intc>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts index 83eca3af44ce..dfa7a37a1281 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts @@ -112,7 +112,7 @@ external_phy: ethernet-phy@0 { max-speed = <1000>; reset-assert-us = <10000>; - reset-deassert-us = <30000>; + reset-deassert-us = <80000>; reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; }; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts index ea45ae0c71b7..8edbfe040805 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts @@ -64,7 +64,7 @@ external_phy: ethernet-phy@0 { /* External PHY reset is shared with internal PHY Led signal */ reset-assert-us = <10000>; - reset-deassert-us = <30000>; + reset-deassert-us = <80000>; reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; interrupt-parent = <&gpio_intc>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts index c89c9f846fb1..dde7cfe12cff 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts @@ -114,7 +114,7 @@ external_phy: ethernet-phy@0 { max-speed = <1000>; reset-assert-us = <10000>; - reset-deassert-us = <30000>; + reset-deassert-us = <80000>; reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; }; };
According to the datasheet (Rev. 1.9) the RTL8211F requires at least 72ms "for internal circuits settling time" before accessing the PHY egisters. This fixes an issue seen on ODROID-C2 where the Ethernet link doesn't come up when using ip link set down/up: [ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down [ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36) [ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma [ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed [ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings") Signed-off-by: Stefan Agner <stefan@agner.ch> --- arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 2 +- arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi | 2 +- arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts | 2 +- 9 files changed, 9 insertions(+), 9 deletions(-)