mbox series

[v7,0/1] dma: qcom: bam_dma: Add support to initialize interconnect path

Message ID 20220921030649.1436434-1-bhupesh.sharma@linaro.org (mailing list archive)
Headers show
Series dma: qcom: bam_dma: Add support to initialize interconnect path | expand

Message

Bhupesh Sharma Sept. 21, 2022, 3:06 a.m. UTC
Changes since v6:
=================
- v6 can be seen here: https://lore.kernel.org/linux-arm-msm/30756e6f-952f-ccf2-b493-e515ba4f0a64@linaro.org/
- As per Krzysztof's suggestion on v6, clubbed the crypto driver and
  dt-bindings changes together. Now the overall v5 patchset into 3
  separate patchsets, one each for the following areas to allow easier
  review and handling from the maintainer:
        arm-msm, crypto and dma
- This patch targets the dma tree specifically.

Changes since v5:
=================
- v5 can be seen here: https://lore.kernel.org/lkml/20211110105922.217895-1-bhupesh.sharma@linaro.org/
- As per Bjorn's suggestion on irc, broke down the patchset into 4
  separate patchsets, one each for the following areas to allow easier
  review and handling from the maintainer:
        arm-msm, crypto, dma and devicetree
- Addressed Rob's, Vladimir's and Bjorn's review comments received on
  v5.
- Added Tested-by from Jordan received on the v5.

Changes since v4:
=================
- v4 for sm8250 can be seen here: https://lore.kernel.org/linux-arm-msm/20211013105541.68045-1-bhupesh.sharma@linaro.org/
- v1 for sm8150 qce enablement can be seen here: https://lore.kernel.org/linux-arm-msm/20211013165823.88123-1-bhupesh.sharma@linaro.org/
- Merged the sm8150 and sm8250 enablement patches in the same patchset,
  as per suggestions from Bjorn.
- Dropped a couple of patches from v4, as these have been picked by
  Bjorn already via his tree.
- Addressed review comments from Vladimir, Thara and Rob.
- Collect Reviewed-by from Rob and Thara on some of the patches from the
  v4 patchset.

Changes since v3:
=================
- v3 can be seen here: https://lore.kernel.org/linux-arm-msm/20210519143700.27392-1-bhupesh.sharma@linaro.org/
- Dropped a couple of patches from v3, on basis of the review comments:
   ~ [PATCH 13/17] crypto: qce: core: Make clocks optional
   ~ [PATCH 15/17] crypto: qce: Convert the device found dev_dbg() to dev_info()
- Addressed review comments from Thara, Rob and Stephan Gerhold.
- Collect Reviewed-by from Rob and Thara on some of the patches from the
  v3 patchset.

Changes since v2:
=================
- v2 can be seen here: https://lore.kernel.org/dmaengine/20210505213731.538612-1-bhupesh.sharma@linaro.org/
- Drop a couple of patches from v1, which tried to address the defered
  probing of qce driver in case bam dma driver is not yet probed.
  Replace it instead with a single (simpler) patch [PATCH 16/17].
- Convert bam dma and qce crypto dt-bindings to YAML.
- Addressed review comments from Thara, Bjorn, Vinod and Rob.

Changes since v1:
=================
- v1 can be seen here: https://lore.kernel.org/linux-arm-msm/20210310052503.3618486-1-bhupesh.sharma@linaro.org/
- v1 did not work well as reported earlier by Dmitry, so v2 contains the following
  changes/fixes:
  ~ Enable the interconnect path b/w BAM DMA and main memory first
    before trying to access the BAM DMA registers.
  ~ Enable the interconnect path b/w qce crytpo and main memory first
    before trying to access the qce crypto registers.
  ~ Make sure to document the required and optional properties for both
    BAM DMA and qce crypto drivers.
  ~ Add a few debug related print messages in case the qce crypto driver
    passes or fails to probe.
  ~ Convert the qce crypto driver probe to a defered one in case the BAM DMA
    or the interconnect driver(s) (needed on specific Qualcomm parts) are not
    yet probed.

BAM dma engine associated with certain Qualcomm Snapdragon hardware blocks requires
relevant interconnect pieces be initialized prior to the dma engine initialization.
For e.g. crypto bam dma engine on sm8250. 

Such requirement is passed on to the bam dma driver from dt via the "interconnects"
property. Add support in bam_dma driver to check whether the interconnect
path is accessible/enabled prior to attempting driver intializations.

If interconnects are not yet setup, defer the BAM DMA driver probe().

Tested on sm8150-mtp, sa8155p-adp, sm8250-mtp and RB5 boards.

Cc: vkoul@kernel.org
Cc: thara.gopinath@gmail.com
Cc: andersson@kernel.org
Tested-by: Jordan Crouse <jorcrous@amazon.com>

Thara Gopinath (1):
  dma: qcom: bam_dma: Add support to initialize interconnect path

 drivers/dma/qcom/bam_dma.c | 10 ++++++++++
 1 file changed, 10 insertions(+)