| Message ID | 20240627193013.1800-1-raymondhackley@protonmail.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | ARM: dts: qcom-msm8226-samsung-ms013g: Add initial device tree | expand |
On Thu, 27 Jun 2024 19:30:30 +0000, Raymond Hackley wrote: > Samsung Galaxy Grand 2 is a phone based on MSM8226. It's similar to the > other Samsung devices based on MSM8226 with only a few minor differences. > > The device trees contain initial support with: > - GPIO keys > - Regulator haptic > - SDHCI (internal and external storage) > - UART (on USB connector via the TI TSU6721 MUIC) > - Regulators > - Touchscreen > - Accelerometer > > --- > v2: Adjust l3, l15, l22 and l27 regulator voltages. Sort nodes. > Set regulator-allow-set-load for vqmmc supplies. > > > > My bot found new DTB warnings on the .dts files added or changed in this series. Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade New warnings running 'make CHECK_DTBS=y qcom/qcom-msm8226-samsung-ms013g.dtb' for 20240627193013.1800-1-raymondhackley@protonmail.com: arch/arm/boot/dts/qcom/qcom-msm8226-samsung-ms013g.dtb: syscon@f9011000: compatible: 'anyOf' conditional failed, one must be fixed: ['syscon'] is too short 'syscon' is not one of ['al,alpine-sysfabric-service', 'allwinner,sun8i-a83t-system-controller', 'allwinner,sun8i-h3-system-controller', 'allwinner,sun8i-v3s-system-controller', 'allwinner,sun50i-a64-system-controller', 'altr,l3regs', 'altr,sdr-ctl', 'amd,pensando-elba-syscon', 'amlogic,meson-mx-assist', 'amlogic,meson-mx-bootrom', 'amlogic,meson8-analog-top', 'amlogic,meson8b-analog-top', 'amlogic,meson8-pmu', 'amlogic,meson8b-pmu', 'apm,xgene-csw', 'apm,xgene-efuse', 'apm,xgene-mcb', 'apm,xgene-rb', 'apm,xgene-scu', 'atmel,sama5d2-sfrbu', 'atmel,sama5d3-nfc-io', 'atmel,sama5d3-sfrbu', 'atmel,sama5d4-sfrbu', 'axis,artpec6-syscon', 'brcm,cru-clkset', 'brcm,sr-cdru', 'brcm,sr-mhb', 'cirrus,ep7209-syscon1', 'cirrus,ep7209-syscon2', 'cirrus,ep7209-syscon3', 'cnxt,cx92755-uc', 'freecom,fsg-cs2-system-controller', 'fsl,imx93-aonmix-ns-syscfg', 'fsl,imx93-wakeupmix-syscfg', 'fsl,ls1088a-reset', 'fsl,vf610-anatop', 'fsl,vf610-mscm-cpucfg', 'hisilicon,dsa-subctrl', 'hisilicon,hi6220-sramctrl', 'hisilicon,hip04-ppe', 'hisilicon,pcie-sas-subctrl', 'hisilicon,peri-subctrl', 'hpe,gxp-sysreg', 'intel,lgm-syscon', 'loongson,ls1b-syscon', 'loongson,ls1c-syscon', 'lsi,axxia-syscon', 'marvell,armada-3700-cpu-misc', 'marvell,armada-3700-nb-pm', 'marvell,armada-3700-avs', 'marvell,armada-3700-usb2-host-misc', 'marvell,dove-global-config', 'mediatek,mt2701-pctl-a-syscfg', 'mediatek,mt2712-pctl-a-syscfg', 'mediatek,mt6397-pctl-pmic-syscfg', 'mediatek,mt8135-pctl-a-syscfg', 'mediatek,mt8135-pctl-b-syscfg', 'mediatek,mt8173-pctl-a-syscfg', 'mediatek,mt8365-syscfg', 'microchip,lan966x-cpu-syscon', 'microchip,sam9x60-sfr', 'microchip,sama7g5-ddr3phy', 'microchip,sparx5-cpu-syscon', 'mscc,ocelot-cpu-syscon', 'mstar,msc313-pmsleep', 'nuvoton,ma35d1-sys', 'nuvoton,wpcm450-shm', 'rockchip,px30-qos', 'rockchip,rk3036-qos', 'rockchip,rk3066-qos', 'rockchip,rk3128-qos', 'rockchip,rk3228-qos', 'rockchip,rk3288-qos', 'rockchip,rk3368-qos', 'rockchip,rk3399-qos', 'rockchip,rk3568-qos', 'rockchip,rk3588-qos', 'rockchip,rv1126-qos', 'st,spear1340-misc', 'stericsson,nomadik-pmu', 'starfive,jh7100-sysmain', 'ti,am62-opp-efuse-table', 'ti,am62-usb-phy-ctrl', 'ti,am625-dss-oldi-io-ctrl', 'ti,am62p-cpsw-mac-efuse', 'ti,am654-dss-oldi-io-ctrl', 'ti,am654-serdes-ctrl', 'ti,j784s4-pcie-ctrl', 'ti,keystone-pllctrl'] from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
Samsung Galaxy Grand 2 is a phone based on MSM8226. It's similar to the other Samsung devices based on MSM8226 with only a few minor differences. The device trees contain initial support with: - GPIO keys - Regulator haptic - SDHCI (internal and external storage) - UART (on USB connector via the TI TSU6721 MUIC) - Regulators - Touchscreen - Accelerometer --- v2: Adjust l3, l15, l22 and l27 regulator voltages. Sort nodes. Set regulator-allow-set-load for vqmmc supplies.