mbox series

[v2,0/2] Add Devicetree support for USB controllers on QCS8300

Message ID 20241011074619.796580-1-quic_kriskura@quicinc.com (mailing list archive)
Headers show
Series Add Devicetree support for USB controllers on QCS8300 | expand

Message

Krishna Kurapati Oct. 11, 2024, 7:46 a.m. UTC
This series aims at enabling USB on QCS8300 which has 2 USB controllers.
The primary controller is SuperSpeed capable and secondary one is
High Speed only capable. Both the High Speed Phys are Femto phys and the
SuperSpeed Phy is a QMP Uni Phy.

Base DT Support has been added for both controllers while only one has
been enabled on Ride Platform. The primary controller has been configured
in device mode. The secondary controller will be enabled in host mode post
addition of SPMI Node which allows control over PMIC Gpios for providing
vbus to connected peripherals.

This series depends on the following series ACKed by upstream maintainers:
Base DT: https://lore.kernel.org/all/20240925-qcs8300_initial_dtsi-v2-0-494c40fa2a42@quicinc.com/

Bindings patches posted at:
https://lore.kernel.org/all/20241009195348.2649368-1-quic_kriskura@quicinc.com/

DTBS Check has been done on the patches.

Link to v1:
https://lore.kernel.org/all/20241009195636.2649952-1-quic_kriskura@quicinc.com/

Changes in v2:
Added quirk to use pipe clk as utmi clk for second controller.
Added wakeup source for second controller.
Modified commit text for DTS change.

Krishna Kurapati (2):
  arm64: dts: qcom: Add support for usb nodes on QCS8300
  arm64: dts: qcom: Enable USB controllers for QCS8300

 arch/arm64/boot/dts/qcom/qcs8300-ride.dts |  23 +++
 arch/arm64/boot/dts/qcom/qcs8300.dtsi     | 168 ++++++++++++++++++++++
 2 files changed, 191 insertions(+)

Comments

Krishna Kurapati Oct. 25, 2024, 5:17 a.m. UTC | #1
On 10/11/2024 1:16 PM, Krishna Kurapati wrote:
> This series aims at enabling USB on QCS8300 which has 2 USB controllers.
> The primary controller is SuperSpeed capable and secondary one is
> High Speed only capable. Both the High Speed Phys are Femto phys and the
> SuperSpeed Phy is a QMP Uni Phy.
> 
> Base DT Support has been added for both controllers while only one has
> been enabled on Ride Platform. The primary controller has been configured
> in device mode. The secondary controller will be enabled in host mode post
> addition of SPMI Node which allows control over PMIC Gpios for providing
> vbus to connected peripherals.
> 
> This series depends on the following series ACKed by upstream maintainers:
> Base DT: https://lore.kernel.org/all/20240925-qcs8300_initial_dtsi-v2-0-494c40fa2a42@quicinc.com/
> 
> Bindings patches posted at:
> https://lore.kernel.org/all/20241009195348.2649368-1-quic_kriskura@quicinc.com/
> 
> DTBS Check has been done on the patches.
> 

Gentle ping for review.

Regards,
Krishna,

> Link to v1:
> https://lore.kernel.org/all/20241009195636.2649952-1-quic_kriskura@quicinc.com/
> 
> Changes in v2:
> Added quirk to use pipe clk as utmi clk for second controller.
> Added wakeup source for second controller.
> Modified commit text for DTS change.
> 
> Krishna Kurapati (2):
>    arm64: dts: qcom: Add support for usb nodes on QCS8300
>    arm64: dts: qcom: Enable USB controllers for QCS8300
> 
>   arch/arm64/boot/dts/qcom/qcs8300-ride.dts |  23 +++
>   arch/arm64/boot/dts/qcom/qcs8300.dtsi     | 168 ++++++++++++++++++++++
>   2 files changed, 191 insertions(+)
>